10-8 Video HD4SD Installation & User Manual - page 28

Manual is about: 4-Ch Dual SD HD MDVR

Summary of HD4SD

  • Page 1

    2016r1 installation / user manual 10-8 hd4sd 4-ch dual sd hd mdvr.

  • Page 2

    2 3 warranty & return information all products • three (3) year free replacement of any failed component. Car camera components 1. Call 1-888-788-1048 and ask for technical support. 2. Visit 10-8video.Com and click on the support section to request a rma. Shipping address 10-8 video llc 1423 huntsvi...

  • Page 3

    4 5 contents safety installation safety 6 avoid electric shock and fire 7 transport & handling 7 daily operation 7 product overview product description 8 features 8 specifications technical specifications 9 electrical specifications 11 system schematic introduction to mainframe 12 hardware: installa...

  • Page 4

    6 7 1. To extend the life of the product, install it in a place free of, or with minimal vibration. 2. To ensure proper heat dissipation, install the dvr in a well ventilated area (such as a trunk). Keep other objects at least 6 inches away. 3. Handle all components with care. Inspect regularly for ...

  • Page 5

    8 9 product overview specifications product description the 10-8 hd4sd is a dual sd card hd mdvr especially designed for use in vehicles. If features four (4) channels of d1/960h/720p video and audio recording and playback, four (4) channels of ahd 720p and one channel of ipc hd video via a full fra...

  • Page 6

    10 11 specifications technical specifications (continued) item parameter description alarm alarm input eight (8) alarm inputs. You can set the lower level alarm (1v or below) or upper level alarm (5v or above) alarm output one alarm output, the higher level of this output is up to 12v communication ...

  • Page 7

    12 13 system schematic note: actual camera appearance may vary from illustration. Introduction to mainframe fig. 1 dvr mainframe fig. 2 dvr mainframe schematic.

  • Page 8

    14 15 device and installation 1. Installation fig. 2 dvr remote fig. 3 electronic lock dvr remote control menu up left right down return to previous menu information enter/select 2 camera split screen cancel sd card info play pause stop fast forward rewind button function info check information quad...

  • Page 9

    16 17 hardware: installation fig. 4 sim and sd card insertion fig. 5 closing the protective cover the device will not power on unless the protective cover is closed and the electronic lock is in the locked position. Hardware installation caution: do not remove sd cards while the device is still on. ...

  • Page 10

    18 19 hardware: installation hardware installation fig. 6 mainframe dimensions and mounting hole positions gps wifi 4g the mdvr can be installed in any direction; there is no need for any part of the device to be pointed in a specific direction. Install the mdvr into a convenient location inside you...

  • Page 11

    20 21 hardware: installation hardware installation fig. 7 power supply connector cable this terminal is connected to the 6-pin power interface on the rear panel of the mdvr. See fig. 2 for its location. Dc12-5a 12v 55ah positive negative yellow acc 1. Check that the battery provides voltage between ...

  • Page 12

    22 23 hardware: installation hardware installation the over-speed alarm feature can be enabled by simply configuring settings via the setup menu alarm speed . A gps signal is required to produce a reading to trigger the alarm. Fig. 8 sensor i/o cable harness fig. 9 high level alarm block diagram +12...

  • Page 13

    24 25 dvr: setup dvr: setup software settings overview after the power supply is connected to the vehicle’s start circuit, ensure the device will automatically start when the vehicle is started. This verifies the power supply is properly connected to the peripherals. After the vehicle starts, the sy...

  • Page 14

    26 27 step 2: set date & time step 3: set vehicle info if gps timing mode is selected, the time will be updated at the “timing time”. You can select timing mode/ ignition mode. By default, ignition mode is used, where you can set the recording delay time after shutdown. The server will monitor and m...

  • Page 15

    28 29 dvr: setup (general) dvr: setup (general) press the “return” button to return to the general menu to enter the user setup menu and to enable the password feature. The original admin password is 888888. If the password is changed the password will be required when re-entering the system setup m...

  • Page 16

    30 31 dvr: setup (recording) dvr: setup (recording) software recording setup press the “return” button twice to return to the setup menu , where you can configure recording settings, including general settings, main code, sub-stream, recording schedule, mirror recording, sd recording and alarm recor...

  • Page 17

    32 33 dvr: setup (recording) dvr: setup (recording) this product is a hybrid hd vehicle mdvr allowing connections from various types of cameras. Table 1 shows interface definitions of various analog cameras. The standard interface is for ip cameras. A user must select a camera type according to the ...

  • Page 18

    34 35 press the “return” button to return to the record setup menu, then enter the s ub-stream settings interface. This setting is directly related to definition and fluidity of the video on the cms software. The higher the resolution, frame rate and bit rate are, the better looking the video will b...

  • Page 19

    36 37 press the “return” button to return to the setup menu, and select the alarm setup interface. Here you can set the sensor, speed, acceleration, temperature, motion detection, linkage settings and other alarm modes. The alarm feature can only be used when an external sensor is connected. Differe...

  • Page 20

    38 39 dvr: setup (alarm) dvr: setup (alarm) press the “return” button to return to the alarm setup menu , and then select the speed setup interface. If the temperature alarm feature is enabled, this information can be transmitted to the central cms system. Press the “return” button to return to the ...

  • Page 21

    40 41 dvr: setup (alarm) dvr: setup (alarm) you can use your remote control within the detection area to select two points as a diagonal to define a detection area. Within the user defined area, when there is an object moving, the system will give an alarm when it is detected. A user can search moti...

  • Page 22

    42 43 1. Enabling or disabling of write metadata is used to check if related alarm information is written tot the video file. 2. To ensure your option changes are saved when you are done, move your cursor to the “save” button and then press the “enter” button. Dvr: setup (alarm) dvr: setup (alarm) p...

  • Page 23

    44 45 press the “return” button to return to the setup menu, and then select the tools icon. Then select the configuration icon to enter the configuration interface. Here you can import/export configuration settings through an sd card or reset to the mdvr to its factory settings. Step 1: configurati...

  • Page 24

    46 47 press the “return” button to return to the setup menu, and then select the tools icon. Then select the log icon to enter the log search interface. Step 3: log search software: configuration fig. 30 log search interface the calendar days with green backgrounds indicate that there is a log that ...

  • Page 25

    48 49 in quad view mode, you can either press the “info” button on your remote control or enter the setup menu to display the system information using the system info icon. Software: system information software: system information fig. 32 system information workflow system information this page left...

  • Page 26

    50 51 q: the mobile device does not output video. Q: the 10-8 hd4sd video interface is different from the camera input interface. Q: gps geographic position is not accurately displayed on map. A: a: a: a: 1. Check the power status of the device. If only one blue indicator led is lit, it indicates th...

  • Page 27

    52 53 a: a: 1. Check if the central registration server is powered on and online. Then check if the device number is used, thereby causing a conflict. Also check if the ip and port number are set correctly for the server center. 2. Check if the device reports information to the server via the built-...

  • Page 28

    54 55 appendix appendix reference tables 10-8 hd4sd memory space reference tools required for 10-8 hd4sd installation 1 2 3 4 5 6 7 8 video record space m/h d1 900 670 540 450 390 350 315 280 hd1 560 420 335 280 245 220 195 175 cif 350 260 210 175 150 135 120 110 960h 904 792 680 567 455 343 229 173...

  • Page 29

    56 57 appendix appendix revision history for: ___________________ (enter serial number here) revision upgrade/change description issue date revised by notes item power cord self tapping screws acc cable wire clips item tie straps electrical tape fire resistant cable housing 10-8 hd4sd additional par...