3Com SSII ADV RPS Y-CABLE TYPE 2 Safety Information
Installing the Cable
The SuperStack II Advanced RPS and its
modules may be hot-connected to SuperStack
II units.
Connecting Cables
Before attaching the cables, check that the
power demand of the product does not
exceed the capacity of the Power Module you
are connecting. This information is given in the
Power Module user guide
(DUA1607-4AAA0X), your Advanced RPS
Chassis user guide (DUA1607-0AAA0X) and
the product user guide. If you are unable to
find the information or are unsure, please
contact your supplier.
Redundancy
Use a standard Type 2 DC cable (as supplied
with your power module) to provide managed
redundancy connecting the outlet of the Type
2A Power Module to the RPS socket on the
rear of the SuperStack device. The device you
are connecting must be one with the
auto-enable feature present for this
redundancy.
Full Redundancy
Use the Type 2 ‘Y’ cable to provide full
redundancy (resilience) connecting one short
lead to each of the two Type 2A Power
Module outlets installed in the RPS chassis and
the long lead to the RPS socket on the rear of
the SuperStack device.
After installing the cable, this guide should be
stored with your other 3Com user guides.
Fault Diagnosis
The LEDs on the front of the Advanced RPS
Chassis provide simple at-a-glance fault
diagnosis of the installed Power Modules.
If you suspect a problem:
■
Check that you have allowed at least five
seconds for the Power Module to warm
up.
■
Check the status of the LEDs on the front
panel of the chassis, as described in the
SuperStack II Advanced RPS User Guide,
part number DUA1607-0AAA0X.
■
Ensure the Power Module is correctly
installed in the Chassis.
■
Check the RPS cables are correctly engaged
and locked.
If you cannot rectify the fault, contact your
supplier, giving the following information:
■
the product number.
■
the Power Module serial number.
■
a brief description of the fault.
Your supplier will advise you on your next
course of action.
DISCLAIMER
Information in this document is subject to change without notice and
does not represent a commitment on the part of 3Com Technologies.
3Com Technologies reserves the right to revise or change this document
without obligation of 3Com Technologies to notify any person of the
revisions or changes. Information contained in this document is believed
to be accurate at the time of publication but no liability whatsoever can
be accepted by 3Com Technologies arising out of any use of this
information.
This document, or any part of it, must not be copied or reproduced on
any medium without the prior consent of 3Com Technologies.
In the unlikely event that this product is found to be damaged on arrival,
or fails to function once installed, you should contact your distributor or
reseller for advice.
ACKNOWLEDGEMENTS
3Com and SuperStack are registered trademarks of 3Com Corporation.
Registered trademarks are registered in the United States, and may or
may not be registered in other countries.
Other brand and product names may be registered trademarks or
trademarks of their respective holders.
Part Number: DUA1607-8AAA02
Revision: 00
Issued: August 2000
© 2000 3Com Technologies
S
UPER
S
TACK
®
II A
DVANCED
RPS
T
YPE
2 ‘Y’ C
ABLE
(3C16078)
U
SER
G
UIDE
Introduction
The SuperStack
®
II Advanced Redundant Power
System (ARPS) provides redundant power
supplies to products in the 3Com SuperStack II
range. These optional Type 2 Advanced RPS ‘Y’
cables (3C16078) are required to connect the
DC power from Type 2A or Type 2 Power
Modules to a SuperStack device when you need
resilience. This cable allows you to hot-swap a
module while maintaining the power supply to
your network unit.
For more general information and warranty
details for these products, please refer to
SuperStack II Advanced RPS User Guide
(DUA1607-0AAA0X).
This guide is written for the installation
engineer and the network administrator who
manages and maintains the network.
Technical Information
Physical
Length
0.92 metre (36 in)
Weight
1050 g (2.3 lb)
Safety Information
Please read the following safety
information before installing the cable.
Installation of this cable should be carried out
by qualified personnel only.
You must not attempt to connect the cable to
any non-RPS power outlet. Damage will result
to both the RPS and the SuperStack II product if
you do.
L’Information de Sécurité
Veullez lire les instructions de sécurité
suivantes avant d’installer le cable.
L’ installation du cable doit être faite
uniquement par un personnel qualifé.
Vous ne devez en aucun cas connecter le cable
à une entrée non RPS. Il en resulterait des
dommages prejudiciales aux produits RPS et
SuperStack II.
Sicherheitsinformationen
Lesen sie vor Einbau des Kabels die
folgende Sicherheitsinformationen.
Der Ein- und Ausbau des Kabels sollte nur
durch Fachpersonal erfolgen.
Verbinden sie das Kabel nur mit dem
vorgesehenen RPS Ausgang. Bei nicht
Beachtung wird der RPS und der SuperStack II
beshädigt.
!
!
!