A & T International CL82101 Quick Start Manual - page 2
Telephone operation
Operation
Steps
Making a call
Press
PHONE or /SPEA E
SPEA E -> Enter the telephone
number.
On-hook dialing
(predialing)
Enter the telephone number -> Press
PHONE or
/SPEA E
SPEA E to call.
Answering a call Press PHONE or /SPEA E
SPEA E , or press any dialing keys
(
0-9, TONE or #).
Ending a call
Press
OFF or return the handset to the telephone base
or charger.
Speakerphone
During a call, press
/SPEA E
SPEA E to switch between
handsfree speakerphone and normal handset use.
Redial
Press
EDIAL repeatedly to select the desired entry ->
PHONE or /SPEA E
SPEA E to call.
Volume control
Press
VOLUMEq to decrease or press VOLUMEp to
increase the listening volume during a call.
Call waiting
(Requires subscription
from telephone
service provider)
Press
FLASH to put current call on hold and to take the
new call; press again to switch back and forth between
calls.
Caller ID
This product supports caller ID services offered by most telephone service providers.
The telephone stores caller ID information for the last 50 incoming calls in the
telephone base. This information is common to all handsets.
Missed call indicator
When a handset is in idle mode and has new or missed calls, its screen shows
XX Missed calls.
You can erase the missed call indicator either by reviewing the call log one by
one, or by pressing and holding
CANCEL on the handset in idle mode.
Review and dial a number in the call log
1.
CID in idle mode-> q or pto scroll through the list.
2.
PHONE or /SPEA E to call when the desired entry is displayed.
Caller ID announce
When this feature is on and you have an incoming call, the handset and/or
base speaks “Call from...” and the name of the caller based on the directory
or caller ID information. You can turn this feature off for the base or each
individual handset, or both.
1.
MENU -> q or p
->
Settings -> SELECT.
2. q or p ->
Caller ID annc -> SELECT.
3. q or p to choose
HANDSET or BASE -> SELECT.
4. q or p to choose
On or Off -> SELECT.
Directory
The directory can store up to 50 entries, which are shared by all system handsets.
Operation
Steps
Adding an entry
1.
MENU.
2. q or p
-> Directory -> SELECT.
3. q or p
-> Add contact -> SELECT.
4. Enter a telephone number up to 30 digits ->
SELECT.
5.
Enter a name up to 15 characters -> SELECT.
Searching/dialing
an entry
1.
DI in idle mode.
2. Press q or p
to browse through the directory, orpress
the dialing keys (
0-9) to start a name search.
3. Press
PHONE or /SPEA E to call.
Answering system
About answering system and voicemail
Your telephone has separate indicators for two different types of voice messages:
those left on the built-in answering system and those left at your telephone
service provider’s voicemail. To listen to messages recorded on the built-in
answering system, refer to the
Message playback section below; to listen to
voicemail, contact your telephone service provider for more information.
Turn answering system on/off
The answering system must be turned on to answer and record messages.
Press
/ANSWE ON on the telephone base to turn the built-in answering
system on or off.
When it is turned on, the
/ANSWE ON light on the telephone base turns on
and
ANS ON displays on the handset.
Message alert tone
When this feature is on, and there is at least one new message, the telephone
base beeps every 10 seconds.
1.
MENU
->
q or p
->
Answering sys -> SELECT.
2.
q or p-> Ans sys setup -> SELECT.
3.
q or p-> Msg alert tone -> SELECT.
4. q or p
-> On or Off -> SELECT.
Call screening
Use this feature to choose whether incoming messages can be heard over the
telephone base speaker when they are being recorded. If you turn call screening
on, you hear the incoming message. While monitoring an incoming message, you
can answer the call by pressing
PHONE or /SPEA E
SPEA E on the handset.
1.
MENU ->
q or p
->
Answering sys -> SELECT.
2.
q or p-> Ans sys setup -> SELECT.
3.
SELECT to select Call screening.
4. q or p
-> choose On or Off -> SELECT.
Message playback
Using the telephone base:
Press
/PLAY
when the telephone base is in idle mode.
Using a handset:
Press
MENU
twice when the handset is in idle mode.
Options during playback
Feature
On the telephone base
On a handset
Adjust playback volume
Press q
/VOL/p
Press q
VOLUME or
pVOLUME
Stop playback
Press
/STOP
Press
5
Skip to the next message
Press
/S IP
Press
6
Repeat the message
Press
/ EPEAT
Press
4
Play the previous message
Press
/ EPEAT twice
Press
4 twice
Delete the message
Press
X/DELETE
Press
DELETE
For more detailed instructions, please refer to the Abridged user’s manual
provided in your package, or for a full set of installation and operation
instructions, refer to the online
CL82101/CL82201/CL82301/CL82351/
CL82401/CL82451/CL82501/CL82551/CL82601 DECT 6.0 cordless
telephone/answering system with caller ID/call waiting Complete user’s
manual at
www.telephones.att.com/manuals
.
For customer service or product information, visit our website at
www.telephones.att.com
or call
1 (800) 222-3111
. In Canada, dial
1 (866) 288-4268
.
© 2010-2011 Advanced American Telephones. All Rights Reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219.
Printed in China. Issue 7 AT&T 09/11.