Summary of W-Thermo
Page 1
Thermostat instruction manual 23.1º.
Page 2: About This Manual
Info@a-touch.In.Th www.A-touch.In.Th about this manual thank you for choosing a-touch solutions. The first chapters of this manual will show you how to configure your unit to operate correctly with your climatization system. Later you will learn how to operate it on a daily basis. At the end you wil...
Page 3: Configuration
Info@a-touch.In.Th www.A-touch.In.Th the a-touch thermostat is a unit that the following basic features: - selectable cycle for summer (cooling) and winter (heating) - programmable temperature schedule independent for winter and summer - temperature scheduling with 3 on periods for each day of the w...
Page 4
Info@a-touch.In.Th www.A-touch.In.Th schedule you may define a temperature schedule for the unit to operate automatically. However, you can switch this schedule off without having to clear it (for example, when you go on vacation). Press key (enter): - the display shows the actual mode. Now change w...
Page 5
Info@a-touch.In.Th www.A-touch.In.Th confirm by pressing key (enter): - the display jumps to the next menu item. Adjust date and time the thermostat needs a clock so that the schedule may run. If the units are interconnected with the bus, then adjusting time in one unit adjusts the time on all the u...
Page 6
Info@a-touch.In.Th www.A-touch.In.Th confirm by pressing key (enter): - now you can adjust the starting hours of the first period. Change with key (up) or (down) confirm by pressing key (enter): - now you can adjust the finishing hours of the first period. Change with key (up) or (down) confirm by p...
Page 7
Info@a-touch.In.Th www.A-touch.In.Th if for example the local unit controls a radiating floor, the heater unit should be local if you wish to heat only with it. You can choose to heat with the air conditioning if you select remote or even both if you want both to heat at the same time. The same appl...
Page 8
Info@a-touch.In.Th www.A-touch.In.Th - there will be no damage if the unit is operated with the wrong unit type selected, just you will not have the correct operation..
Page 9: Unit Operation
Info@a-touch.In.Th www.A-touch.In.Th unit operation switching on and off the thermostat has 4 modes: off, where the thermostat does not work at all, schedule is off auto off, where the thermostat runs the program you defined but is in an off period auto on, where the thermostat runs the program you ...
Page 10
Info@a-touch.In.Th www.A-touch.In.Th moment you change the temperature, then the new temperature is stored in all active periods, regardless of if they were different or not. To adjust the temperature, proceed as follows: press the key (up) to increase the temperature: - the target temperature is sh...
Page 11
Info@a-touch.In.Th www.A-touch.In.Th using 2 units with 1 thermostat as explained above, it is possible to use one thermostat to control 2 different climatization units. So that this is possible, the slave actuator (remote) must be associated with the master actuator (local) that is the unit that is...
Page 12: Integration With Domotics
Info@a-touch.In.Th www.A-touch.In.Th switching the second unit on and off if the heater or cooler unit selected is local or remote (operation with just one unit), it is possible to switch temporarily the mode to both without changing the cooler or heater unit in the configuration menu. To switch the...
Page 13
Info@a-touch.In.Th www.A-touch.In.Th - the scenario will select directly the mode as defined for the scenario, regardless of its starting mode. - you cannot change the temperature or the ventilation speed with a remote key. Associating a key to the thermostat the programming follows exactly the same...
Page 14
Info@a-touch.In.Th www.A-touch.In.Th if you need to temporarily operate the thermostat proceed as follows: press the keys (up) and (vent) together briefly: - the display layout changes to thermostat mode for 5 seconds. You can now operate the keys of the thermostat. Every press renews the 5 seconds ...