Access LORADO Installation Instructions And Owner's Manual

Manual is about: Roll-Up Cover

Summary of LORADO

  • Page 1

    1 thank you for purchasing access ® lorado ® roll-up cover. Aci ® manufactured this cover with pride using superior quality materials and workmanship. With proper care, your cover will provide years of service and enjoyment. Notice to installer: it is recommended instructions are read before install...

  • Page 2: Installation Instructions:

    2 a. Position side rail with weather strip against inside lip of box. Push rail forward until it touches front of box. End of rail with strike goes to rear. 1. Installing cover side rails top of rail should be flush with top side of box at front nylon strike to rear note on bed liners: with an under...

  • Page 3

    2 3 this surface of rail should be level after clamps are tightened and even with top of tailgate or tailgate protector height of tailgate with protector adjust clamps up or down until they hold rail level when tightened 2nd clamp see note for 4th clamp 3rd clamp 1. Installing cover side rails (cont...

  • Page 4: 2: Apply Element Seal

    4 note: for best adhesion, air and surface temperature should be above 60 0 f. A. Clean underside of rail with alcohol pad included. Hold seal up to end of rail, make sure end of seal contacts edge of box. B. Mark leg of seal and cut notch in seal. Rail edge of box mark for cutting rear seal rail a....

  • Page 5

    4 5 c. Peel paper back, align and adhere seal at end of rail. D. Edge seal installed. Rail edge of box rear seal trim excess seal c. D. 3: apply rear seal (continued) a. The cover comes pre-rolled in its normal open position for ease of installation. Set pre-rolled cover on tailgate with front bar f...

  • Page 6

    6 c. Hold bolt at top and tighten nut under side rail. Repeat procedure for right tension adjuster. Center front bar between rails until space is equal at both ends tab goes under - then tighten bolt 5. Mounting cover to side rails a. Set rolled up cover on rails at front of box (behind cab) with fr...

  • Page 7

    6 7 a. Unroll cover and place rear bar into strikes on side rails. Press down on bar to close (20-30 lbs pressure). The cover fabric may be tight. Over time, under tension, it will conform to its hardware and loosen slightly. If bar is too hard to push down, adjust tensioners equally as needed to cl...

  • Page 8: To Close

    8 release retainer straps at front and using both hands, roll cover to rear of box. Alongside of box, seal cover edges with hook and loop seal- ing system the full length of cover on both sides. Pull with one hand and seal with other hand. Position roll-up bar against strikes. Push down on bar until...

  • Page 9: Strap Adjustment

    8 9 premium storage straps front bar xt-dial tm tension adjuster front element seal tm rail clamps 6–most short boxes 8–long boxes left side rail rear seal autolatch tm ii dual locking system on rear bar right side rail rear bar support bows to tighten storage strap, pull back on top layer of strap ...

  • Page 10: Troubleshooting

    10 autolatch tm ii doesn’t engage check side rails for height and level. (refer to step 1f) inspect latches for jammed or broken parts. Problem solution troubleshooting cover too loose turn both tension adjusters counter clockwise to move front bar forward. (refer to step 6c, see arrows next to adju...

  • Page 11: Inspection And Maintenance

    11 11 • inspection and much of the maintenance can be done by the operator. It may be necessary to review the installation and operating instructions. • periodically inspect the cover assembly and the condition of all parts. Check for loose bolts and parts, tighten if needed. Test the operation to e...

  • Page 12

    12 access ® and lorado ® are registered united states trademarks of agri-cover, inc. For aci patent information, please visit: http://www.Agricover.Com/patents/ phone 866-630-8726 8:00 am - 5:00 pm cst monday through friday except holidays access - a division of agri-cover, inc. 062016 pn 50219_7 pr...