Accusplit AE2740 Instructions

SETTING UP YOUR PEDOMETER 

To record your distance accurately, you will need to 

set your stride length. 

Finding Your Stride Length:

 Your stride length is the 

length of one of your steps, measured from “toe to 

toe.” To measure, walk 10 steps with your normal 

stride and measure the TOTAL DISTANCE from the 

toe of your starting step to the toe of your 10

th

 step 

(see diagram below). Divide the TOTAL DISTANCE 

by 10, and multiply the decimal portion by 12 to find 

your stride length in feet and inches. Example: If you 

walk 23 feet in 10 steps, your stride length is 2.3 feet. 

Multiply 0.3 x 12 = 4. Your stride length is 2 feet, 4 

inches.

Setting Your Stride Length: 

Repeatedly press the red 

MODE button until indicator points to “DIST.” Press 

the blue SET button once to enter setting mode. 

Display will shift to show stride, in feet and inches. 

Press and hold down the blue SET button to increase 

stride length. Press the red MODE button to exit 

setting mode. 

Note:

 Pressing the white RESET button resets  

stride length to 2' 0". 

AE2740 Pedometer

INSTRUCTIONS

ACCUSPLIT

, Inc.  •  3090 Independence Drive, Suite 148  •  Livermore, CA 94551 USA

800-935-1996  •  925-290-1900  •  FAX 925-290-1930  •

www.ACCUSPLIT

.com  •  support@ACCUSPLI

T

.com

Attaching the Leash:

 Attach the pedometer to the 

leash by looping the leash through the pedometer 

leash slot. Next, loop the leash through the metal 

clip, then clasp the waistband of your clothing  

with the pedometer belt clip. You can also use a  

safety pin to fasten the leash to your clothing, loop 

the leash through your belt or belt loop, or use a 

badge holder. 

VIEWING YOUR RESULTS

Once you put on your pedometer with the cover 

closed, it will automatically begin to record your 

steps, distance, and activity time. Repeatedly 

press the red MODE button to cycle through the 

pedometer modes: 

STEP 

→

 DISTANCE 

→

 ACTIVITY TIMER 

→

 STEP

RESETTING YOUR PEDOMETER

Most people prefer to reset step and distance daily. 

To reset: From STEP, DISTANCE, or ACTIVITY TIMER  

mode, press and hold the white RESET button for at 

least 2 seconds.

CHANGING UNITS (English vs. Metric)

The Pedometer can display either in English units 

(inches, miles, and pounds - this is the default), or in 

Metric units (cm, km, and kg). To change between 

display modes, push and hold the red MODE button 

for 5 seconds, until you see all display indicators 

momentarily come on. You can check to see which 

system of units you are using by repeatedly pressing 

the red MODE button until it displays either MI or KM 

when showing Distance traveled.

REPLACING THE BATTERY

When the display starts to dim or goes blank, it is 

time to replace the battery. Your pedometer uses one 

Type L1142 (LR43) 1.5 volt silver oxide battery.  

To replace:

1.  Insert a coin into the slot on the front of the  

  case, and twist counterclockwise to loosen  

  the battery door.

2.  Remove battery door and take out the old  

  battery. Replace it with a new battery. The  

  battery’s positive (+) terminal should be  

  FACE UP while you put it into the pedometer.

3.  Put the battery door back on and twist the  

  coin clockwise to tighten.

Congratulations on taking the first step to wellness 

with your purchase of an ACCUSPLIT pedometer. 

It’s easy to set up your new pedometer. 

Just follow the steps below, and start walking!

10 steps

 970-077

First, loop the

pedometer leash slot

Next, loop the metal 

clip, then clasp clothing

Or, loop a  

badge holder,  

then put into pocket

(Badge holder  

not included)

Or, loop a belt or belt loop

Red: 

MODE

9789

STEP

DIST

▶

Blue: 

SET

White: 

RESET 

DISPLAY MODES 

•

  STEP: 

STEP

 mode shows your step count 

since last reset, up to 1,000,000 steps.

•

  DIST: 

DIS

T

ANCE mode shows distance 

walked or jogged since last reset.

•

◯

: 

ACTIVITY 

TIMER MODE

shows 

total activity time in minutes and 

seconds since last reset.

The timer 

runs automatically whenever steps 

are being recorded.

HOW TO OPEN YOUR PEDOMETER

See diagrams at right.

The cover must be closed  

for the pedometer to work.

ACCUS

PLIT

ALLIANC

E

 1520

A

CCU

STEP

10000.ORG   

RESET

ACTIVITY

PEDOME

TER

STEP

0

68440

WEARING YOUR PEDOMETER

Gently slide the pedometer onto your belt or the 

top edge of your pants or skirt. It should fit snugly 

and level, above one knee. The strong steel clip 

makes it easy.

Note:

 The pedometer should be as vertical as 

possible. Walkers with larger stomachs may find it 

helpful to wear the pedometer farther back on the 

body, toward one hip. 

The cover must be closed for the pedometer to 

work. 

To avoid losing or dropping your pedometer, use 

the included leash and clip to fasten the pedom-

eter securely to your clothing.

yes

no

3-STEP DELAY FILTER

ACCUSPLIT has added a “3 step delay” filter to this pedometer, to weed out false steps caused 

by tapping the foot, sitting down, etc. The filter is set to “3 steps,” meaning that the unit will wait 

to start counting steps until more than three steps have been recorded. When you are beginning 

a walk, the display will not show any steps for a few seconds. After the unit has sensed four 

steps, the display will register all of those steps at once, and keep counting from that point.