Audio Note AN TT-1 Manual
Dear Customer,
Thank you for purchasing the Audio Note TT-1 turntable. A few minutes
reading these instructions will ensure maximum enjoyment and ease of
use.
1. Carefully unpack all parts and remove polythene bags etc.
2. Place turntable on a level flat surface free from vibration. A wall
mounted shelf or preferably an equipment stand would be ideal for this
purpose.
3. Remove transit screws to release the sprung sub-chassis. Remove the
armboard fastening bolts with the 3mm allen key provided. This will allow
easy installation of the chosen tonearm and cartridge. Install the tonearm
parallel with the edge of the armboard (although only an aesthetic
requirement) and in strict accordance with the manufacturer’s
instructions. Refit the armboard and tonearm to the turntable and
replace fastening bolts without fully tightening them. At this stage the
drive belt should be fitted around the small drive pulley and acrylic drive
hub, finally placing the platter onto the top of the hub. Notice the two
grooves in the drive pulley. The top groove is for 33rpm and the bottom
for 45rpm playback.
4. With the tonearm and platter in place the sprung sub-chassis can be
properly levelled. Making sure that the turntable plynth is level, adjust the
three chassis adjustment screws with the 4mm allen key provided. The
bottom edge of the platter should be 5mm above the plynth. Turn the
screws clockwise to raise the suspension and anti-clockwise to lower it.
At this stage affix the tonearm cable into the white clip at the back fo the
plynth, making sure the suspension can move freely up and down, then
tighten the armboard bolts. The final tonearm and cartridge alignment
adjustments can now be made.
5. Some tonearms have a separate earth lead which can be attached to
the earthing post. Other tonearms do not require this.
6. Do not remove the drive hub from the bearing assembly as a quantity
of oil and ball bearing have been fitted from the factory. A small syringe of
oil has been supplied in case of loss or spillage, of which only 2-3 drops
are required.
7. The attractive grey paint finish is extremely hard wearing and stable.
To keep up its visual appeal it should be dusted carefully with a clean,
soft paintbrush as required. For more stubborn marks or stains, a
degreasing fluid approved for painted surfaces on a sponge can be
used.
Thank you for taking a few minutes to read these
simple instructions and we wish you hours
of enjoyment and happy listening.
AN TT-1
Entry Level Analogue Products
Tonearm cable clamp
Earth post
Chassis adjustment screws
Specifications:
Motor:
Power Source:
Power Consumption:
Speeds:
Drive System:
Distance:
Dimensions:
(Spindle to arm-mount
centre)
24 Pole precision high torque
motor mounted on an anti-
vibration assembly.
240v 50Hz or 110v 60Hz
depending on destination
country.
3.3VA
33 & 45 rpm, Manual change
Precision moulded round
section rubber belt.
220mm
47 x 36 x 17cm including lid and
feet
Audio Note (UK) Ltd., 25 Montefiore Road, Hove, East Sussex BN3 1RD, United Kingdom
Tel: +44 (0)1273 220 511 Fax: +44 (0)1273 731 498 www.audionote.co.uk
Audio Note is the only high end hifi company to design and
manufacture complete analogue and digital systems in-house. Our
product range spans Cartridges, Tonearms, DACs, CD-Transports,
Amplifiers, Loudspeakers, Speaker stands and Cables plus a wide
range of carefully selected high quality components.
The same sonic assessment criteria are applied to each individual
component and therefore all our components will remain consistent
with each other regardless of price. We regard the system as a
where complimentary design parameters and their realisation result
in a level of emotional involvement and musical enjoyment
unobtainable in other systems.