B.H.M E-ROAD User Manual - page 4

Manual is about: ELECTRIC BICYCLE

Summary of E-ROAD

  • Page 1

    1 user guide electric bicycle e-road thank you for your purchase of your new e-road to insure that you are fully satisfied with your new electric bike for the longest possible time, we invite you to take knowledge of this user guide .It will give you all the necessary information for the maintenance...

  • Page 2

    2 the 21st century will be the one to resolve the problem between the development of means of transportation and the downgrade of the quality of life. The electric bicycles are means of transportations that are clean and contribute in the upgrade of the quality of life for all. The e-road is a produ...

  • Page 3

    3 technical characteristic dimensions (lxlxh) 1645x620x1010mm wheel base 1130mm net weight (without battery) 143lb maximum speed 20 mph max loading weight 125kg battery life ~35 miles pedaling speed 4 mph battery capacity 14ah voltage 48v motor power 500w threshold protection for weak voltage 42v±0,...

  • Page 4

    4 front light handle bars rear view mirror commando dash board front basket front fork blinker ignition switch helmet hook front wheel frame pedal crank stand shock absorber foot peg protection cover expansion brake blinking signal light brake light electric motor seat battery compartment under the ...

  • Page 5: Attentio

    5 pedals installation step initial step piece actions intermediary state or final attentio n 1 crank align the wholes of the crank with the fixation support 2 bolt fasten the crank to its support with the bolt that is planned for this effect, screw bolt very tightly 3 cap place cap on top of bolt.. ...

  • Page 6

    6 installation of front basket or facade step initial state actions 1 unscrew the 2 top screws with the help of a phillips screw driver, keep screws on the side. Locate the 4 fixation points. 2 take basket out of packaging and open as shown in the picture on left .You will then be able to locate the...

  • Page 7

    7 installation of steering (handle bars) step initial state actions 1 remove plastic cover to access steering column. 2 remove handle bars from its packaging and place on steering column as is shown in the picture opposite .Coincide all the wholes and insert the fixation bolt. 3 tighten bolt and put...

  • Page 8: Operation

    8 operation safety tips 1) we strongly recommend to attentively read this user guide before using your e-road so as to really understand the way it functions. 2) please respect the codes of the road (laws) and ride on appropriate roads. 3) your electric e-road rides faster than a conventional bike, ...

  • Page 9

    9 the commands high beam switch: controlee who allows switching between high beams and head lights. Turning signals : push on the switch right or left to signal right or left, press on middle of switch to turn signal off. Light switch: position lights off position dashboard light on position lights ...

  • Page 10

    10 before taking the road. 1) check tire pressure (2.0 bars in front and 2.2 bars in back) 2) check battery level. 3) check braking system efficiency and if motor shuts off when brakes are applied. Ignition: 1) insert the key and turn it to the symbol on ( ), the dashboard lights up and the motor is...

  • Page 11

    11 use and maintenance of the battery battery characteristics: reference voltage capacity dimensions weight (lbs) l l h 6-dzm-12 48v 14ah 152±3 98±2 94±2 9810 your e-road is equipped with a lead-acid battery completely waterproof, which has these advantages: 1) low self discharge 2) leak proof struc...

  • Page 12

    12 use of the battery charger: battery charger characteristic entrance voltage time of charge current of charge alternate current 100-250v, 50/60hz 48v 6-8 hours 1,6a±0,2a how to charge the battery: 1. Lift open the seat to access the battery 2. Disconnect the main power cable ,and 3. Connect the ex...

  • Page 13

    13 during the charging, the charger blows out some heat. Do not cover or put it next to flammable materials. The charging process has to be in a dry and aired out place in order to dissipate the heat. If the charger doesn’t stop charging after 10 hours, stop charging and call customer service. Use o...

  • Page 14

    14 brakes and chain adjusting back brake adjusting tighten the adjusting bolt until the leeway of the lever of the back break is about 10 to 20 mm. Attention: after the adjusting done, the back wheel should be able to spin freely. Front brake adjusting tighten the adjusting bolt to get a firmer resp...

  • Page 15

    15 maintenance the following maintenances have to be done as regularly as possible, general rule, once a week: 1) clean the surface of the motor and of the entire e-road. 2) verify the motor and the pod of connection. 3) check the fixation of each element, retighten the screws if necessary. Regular ...

  • Page 16

    16 repair symptom possible causes solution ignition on ,and the display board doesn’t turn on 1. Mischarge of the battery 2. The fuse has melted 3. The niemen is defective 4. Wrong connection of dashboard 5. Low battery charge 1. Clean the battery terminal 2. Change the fuse 3. Change the neiman 4. ...

  • Page 17

    17 connector controller..