B&K MZ-128 Reference Sheet

POWER

POWER

1

1

2

2

3

3

4

4

7

7

5

5

8

8

0

0

6

6

9

9

ENTER

ENTER

IN 8

IN 8

TUNE-

TUNE-

SAVE

SAVE

MENU

MENU

EXIT

EXIT

LOUD

LOUD

OFF

OFF

MUTE

MUTE

IN 9

IN 9

+10

+10

AM

AM

M

M

T+

T+

S+

S+

FM

FM

V+

V+

T-

T-

S-

S-

B

& K Components, Ltd.

Model MZ-128

SEL

SEL

ENTER

ENTER

VOLUME

VOLUME

PRESET

PRESET

ON/OFF

ON/OFF

B+

B+

B-

B-

Õ

®

°

¯

ZONE

ZONE

VIDEO +

VIDEO +

BASS

BASS

TREBLE

TREBLE

SOURCE

SOURCE

ST/M

ST/M

LOUDNESS

LOUDNESS

DEDICATED

DEDICATED

D-IN

D-IN

TUNE+

TUNE+

STA-

STA-

STA+

STA+

UP

UP

DOWN

DOWN

L

E

F

T

L

E

F

T

R

 I

G

H

T

R

 I

G

H

T

B

&

K CT Series MZ-128 Remote Controller Reference Sheet

The MZ-128 Remote Controller has multiple useful functions:

1) The MZ-128 Remote Controller may be used to control and setup a CT610/310/600. 

2) The 

learning keypads etc...

3) The 

 may be set to source 

code sets 000-128

     and 999.

MZ-128 may be used as a source of IR for use in programming 

MZ-128

the B

&

K IR functions listed below, for 

Setup the MZ-128 to use a discrete B

&

K code set:

1) Install 4 AAA batteries into the remote. Observe polarity.

2) Press and hold the B

&

K and MUTE buttons simultaneously for two seconds. The LED will 

    light up solid red and stay illuminated.

3) Firmly press the desired B

&

K three digit code set. Always use three digits (i.e. 0-1-1 default

    for Zone A)                                                    

4) Press the B

&

K button again to confirm setup. The red LED will blink three times when the IR 

CODE SET 000-128

MZ-128 BUTTON

B

&

K IR FUNCTION

MZ-128 BUTTON

B

&

K IR FUNCTION

[POWER STATE]

[TUNER]

B&K

POWER ON

AM

SELECT THE AM BAND

POWER

POWER TOGGLE

FM

SELECT THE FM BAND 

OFF

POWER OFF

TUNE +

TUNE FREQUENCY UP

TUNE -

TUNE FREQUENCY DOWN

[VOLUME]

STA +

TUNER FAV PRESET UP

MUTE

MUTE TOGGLE

STA -

TUNER FAV PRESET DOWN

VOLUME 

MASTER VOL UP

M

STEREO / MONO 

VOLUME 

MASTER VOL DOWN

[NAVIGATION]

[TONE CONTROL]

MENU

MENU UP/DOWN LEVEL

B+

BASS UP

LEFT 

LEFT OR BALANCE (L)

B-

BASS DOWN

RIGHT 

RIGHT OR BALANCE (R)

T+

TREBLE UP

SEL/ENTER

SELECT OR ENTER

T-

TREBLE DOWN

UP

UP

LOUD

LOUDNESS TOGGLE

DOWN

DOWN

SAVE

SAVE

[INPUT SOURCE]

EXIT

TOTAL EXIT FROM ALL MENUS

S+

SOURCE UP

ZONE

ZONE SELECT

S-

SOURCE DOWN

V+

VIDEO SOURCE UP

[NUMERIC]

D-IN

ZONE DEDICATED IN

    0

    0

AM

TUNER AM

    1

    1

FM

TUNER FM

    2

    2

IN 1 

IN 1 OR [V1]

    3

    3

IN 2 

IN 2 OR [V2]

    4

    4

IN 3 

IN 3 OR [TV]

    5

    5

IN 4 

IN 4 OR [DVD]

    6

    6

IN 5 

IN 5 OR [CD]

    7

    7

IN 6 

IN 6 OR [SAT]

    8

    8

IN 7 

IN 7 OR [TAPE]

    9

    9

IN 8 

IN 8 OR [V4]

+10

+10

IN 9 

IN 9 OR [V5]

[FAVORITE PRESET]

PRESET   

FAVORITE PRESET UP

PRESET   

FAVORITE PRESET DN

CODE SET 999

MZ-128 BUTTON

B

&

K IR FUNCTION

[B

&

K ALL COMMANDS]

ON/B

&

K/POWER ALL B

&

K POWER ON

OFF

ALL B

&

K POWER OFF

VOLUME ALL 

B

&

K VOLUME UP

VOLUME ALL 

B

&

K VOLUME DOWN

0

ALL B

&

K VOLUME    0 DB

2

ALL B

&

K VOLUME -20 DB

4

ALL B

&

K VOLUME -40 DB

6

ALL B

&

K VOLUME -60 DB

MUTE

ALL B

&

K MUTE TOGGLE

B

& K

B

&

K

MZ-128 Default Factory Code-Set is: 0-0-0 Whole House Control

Code-Set 128 Simply Explained

Code-Set 128 is a special code-set which 

allows individual control of the Hardware Zone 

that the IR Data is received by. It will not function 

when received by the unit’s front panel. I.e., Two 

keypads are plugged into Zone A & B’s Control 

I/O Ports, when the remote comes into IR view 

of the keypad in Zone A, the 128 Code-set 

remote will only control Zone A, when in Zone A. 

Take that same remote into Zone B and it will

only control Zone B.