BAK PLANON Operating Manual

Other manuals for PLANON: Operating Instructions Manual
Manual is about: Overlap welding machine

Summary of PLANON

  • Page 1

    Bak thermoplastic welding technology ag 1 1 operating manual overlap welding machine type planon / planon digital this operating manual must be available to the operating personnel at all times. Read the operating instructions carefully before use and keep for further reference. Application the plan...

  • Page 2

    Bak thermoplastic welding technology ag 2 security warning danger of life when opening the tool as live components and connections are exposed. Unplug the tool before opening it. Danger of fire and explosion in case of incorrect use of the welding machine especially near combustible materials. Never...

  • Page 3

    Bak thermoplastic welding technology ag 3 the machine must not be used on inflammable subsurface (e.G. Housetops and floors made of wood) the tool must be protected from damp and wet because of its protection mark ip20. When using the machine on roofs and tables it could fall down because of its aut...

  • Page 4

    Bak thermoplastic welding technology ag 4 technical data planon tape/vandalism voltage v 120 230 120 230 frequency hz 50 / 60 power consumption w 2’700 3’400 2’700 3650 max. Power input a 22,5 15,0 22,5 16,0 temperature °c 20 – 600 drive m/min standard 0,6 – 12,5 / digital 0,0 – 12,5 max. Air flow (...

  • Page 5

    Bak thermoplastic welding technology ag 5 bring the welding machine into the right welding position. Outside edge of the overlap, outside edge of the pressure roller and outside edge of the guide roller must form a line (see image). Device description standard operating panel digital operating panel...

  • Page 6

    Bak thermoplastic welding technology ag 6 6. Welding temperature adjustment 6.A welding temperature adjustment 6.B reduce temperature 6.C increase temperature 7. Hot air system 8. Guide roller 9. Carrying handle 10. Weight (optional additional weight) 11. Lifting device 12. Pressure roller basic adj...

  • Page 7

    Bak thermoplastic welding technology ag 7 basic adjustments custom tape perform adjustments only in cold condition (danger of burns!). Nozzle adjustment loosen the screws on the bracket to change adjustments on the nozzle. See below drawings for the recommended adjustments. Nozzle adjustment guide r...

  • Page 8

    Bak thermoplastic welding technology ag 8 welding operating condition: maintain the maximal allowed impedance z max = 0.301 Ω + j 0,188 Ω . Consult your local electricity board if necessary. Check adjustment of the nozzle. The mains supply must conform to ice 60364 standard as well as to the nationa...

  • Page 9

    Bak thermoplastic welding technology ag 9 1.7. Insert the new heating element - observe marking, voltage and power rating 1.8. Slide on the mica tube 1.9. Slide on the gasket and position the boreholes 1.10. Slide on the nozzle and fix with 4 screws 1.11. Readjust the nozzle as described under basic...

  • Page 10

    Bak thermoplastic welding technology ag 10 service and repair the welding machine should be checked by an authorised service centre approx. Every 1000 operating hours. Repairs have to be carried out exclusively by bak authorised service centres. For repairs, please return the device appropriately pa...

  • Page 11

    Bak thermoplastic welding technology ag 11 assembly instructions for accessory no. 2: adjustment of the welding seam art.No. 5230155 art.No. 5230156 art.No. 5230157 overlap nozzle 20mm overlap nozzle 30mm overlap nozzle 40mm pressure roller 20mm pressure roller 30mm pressure roller 40mm required too...

  • Page 12

    Bak thermoplastic welding technology ag 12 assembly instructions for accessory no. 3: hem kit art.No. 5230109 hem kit 2 x screw m4x20mm required tools: allen key sw4/5, crosstip screwdriver 3.0. Adjustment of the hem kit: 3.1. Switch off the device 3.2. Unplug the tool 3.3. Adjust the hem width cons...

  • Page 13

    Bak thermoplastic welding technology ag 13 assembly instructions for accessory no. 4: keder accessory kit art.No. 5230192 art.No. 5230193 basis is here a planon overlap keder roller 30mm keder roller 40mm welding machine with 30mm or 40mm seam width!!! Required tools: allen key sw3/5, torx wrench t2...

  • Page 14

    Bak thermoplastic welding technology ag 14 assembly instructions for accessory no. 5: guide handle art.No. 5230077 guide handle allen screw m8x25 required tools: allen key sw6 5.0. Adjustment of the rand accessory kit: 5.1. Switch off the device 5.2. Unplug the tool 5.3. Lay the tool down to the sid...

  • Page 15

    Bak thermoplastic welding technology ag 15 spare parts drawings heating element and nozzle lifting device 5230043/5230044/5230045 5230169/5202010 6101760 5101270 5113269/5113267/5113270 5230054 5230112 5280284 5230036 5230055 5230037 5230097 5102503 5102504 5100985 5102236 5280221 5107716.

  • Page 16

    Bak thermoplastic welding technology ag 16 guide rollers art. No. Description quantity (parts) 5230043 overlap welding nozzle 20 mm 1 5230044 overlap welding nozzle 30 mm 1 5230045 overlap welding nozzle 40 mm 1 5202010 rounded head screw m4x12, torx 1 5230169 rounded head screw m4x16, torx 3 610176...

  • Page 17

    Bak thermoplastic welding technology ag 17 deutsch eg-konformitätserklärung herz-gmbh, a-6141 schönberg/austria, bestätigt, dass das nachfolgende produkt in der von uns in verkehr gebrachten ausführung die anforderung der folgenden richtlinie(n) erfüllt. Bezeichnung des gerätes : schweissautomat typ...

  • Page 18

    Bak thermoplastic welding technology ag 18 lietivi ų atitikties deklaracija herz-gmbh, a-6141 schönberg/austria, mes patvirtiname, kad šio produkto modelis, paleistas į apyvart ą , pilnutinai atitinka sekan č ias eb direktyvas. Į rankio aprašymas : suvirinimo į renginia tipas : planon direktyvos : e...

  • Page 19

    Bak thermoplastic welding technology ag 19 norsk deklaration av samsvarsmåling fra herz-gmbh, a-6141 schönberg, bekrefter at denne modellen av vårt solgte produkt oppfyller kravene i følgende ef- direktiver. Beskrivelse av verktøyet : sveiseapparat typ : planon direktivene : emc-direktivet 2004/108/...

  • Page 20

    Bak thermoplastic welding technology ag 20