-20ºc ÷ +55ºc 9 v dc ÷ 14 v dc sma antenna connector ip65 8 channels bnc video bnc video utp video 5,8 ghz 25 mw fm pal ntsc video: 10 channels 869 mhz 300 mw gfsk rs-485 data: operating manual warranty terms cam-9 wireless system for simultaneous transmission of video, audio and control for ptz cam...
Declaration of conformity i, the undersigned, representing the following company: camsat przemysław gralak ul. Ogrodowa 2a 86-050 solec kujawski hereby declare, with full responsibility, that the following device: cam-9 is approved for operation within the eu and conforms to the fundamental requirem...
Table of contents product features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 kit contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 recommendations . . . . . ...
4 product features the cam-9 kit is an integrated transmission system comprised of a module for video transmission and data transmission to and from industrial cameras in a single compact case . Kit contents the kit includes: 1 3 5 4 2 antenna side 1 . Video/audio transmitter (tx) with an ip65 anten...
5 recommendations 1 . Larger systems consisting of a few kits should be started up and set up one after another, i .E . The power supply should be connected to the next kit only after the previous kit has been set up precisely . 2 . It is recommended to install cam-9 receivers at least 7 m away from...
6 technical data dane audio-wideo frequency 869 mhz 5 .8 ghz number of operating channels 10 8/16* radio link modulation gfsk fm eirp radiated power 300 mw 25 mw receiver sensitivity −118 dbm@1200 bps / −114 dbm@9600 bps ≤ −85 dbm antenna connectors sma-rp f 50 Ω sma-rp f 50 Ω antenna characteristic...
7 [a] - 869 mhz antenna [b] - led display [c] - power diode [d] - link diode [e] - diode signalling data transmission [f] - rotary switch for setting video channels [g] - rotary switch for setting data channels [h] - set button [i] - enter button [j] - on/off switch for the 120 Ω terminator on the r...
8 switch settings installation 1 . Fasten the transmitter and receiver to a stable pole with the mounts. 2 . Screw the 869 mhz [a] antennas into sma antenna connectors at the top of the case . 3 . Connect the video cables with the coaxial cable [m], or the utp twisted pair cable [n] . 4 . Connect th...
9 basic settings operating the dip-switch switch 1 [j] – enables / disables the 120 Ω resistor (terminator) in parallel with the rs-485 interface terminals . This resistor should always be added at the end of every rs-485 line to avoid interference . In order to enable the resistor (rs-485 line term...
10 method for setting the transmission rate and data format 1 . In order to get to the settings, enter the device menu by holding the enter button [i] for three seconds (until appears on the display) . 2 . You can switch between the menu options ( , , ) by pressing the enter button [i] shortly . 3 ....
11 advanced settings in order to use the advanced options, devices operating at the same building should be paired together . All the cam-9 tx transmitters should be assigned to the cam-9 m rx receiver memory . Procedure for assigning transmitters to the receiver memory 1 . Select the option from th...
12 setting the video operating channel remotely in order to set the video transmission operating channel (for a specific transmitter) remotely from the cam-9 m rx receiver level, do the following: 1 . Select the option from the main menu . 2 . Select the identification number of the transmitter whos...
13 testing from the cam-9 tx transmitter level - if, after testing is completed, the display alternates between (ok) and the transmitter’s id number, it indicates a correct transmission . - if , appears on the display, it indicates a transmission error (check the connections and test again) . Testin...
14 general warranty terms camsat grants a 24 month warranty for the cam-9 transmission kit 1 . If the device is not be operating properly, make sure, before returning the device for servicing, that everything was done according to the operating manual . 2 . If the faulty device is returned or send i...
The warranty does not cover - mechanical damage of devices and failures occurring due to fortuitous events, such as: fire, power grid overvoltage, electrical discharges, power supply, effects of chemical substances. - damage occurring due to: improper handling of the device, using the device against...
Manufacturer: camsat gralak przemysław ul . Ogrodowa 2a 86-050 solec kujawski product offer and information: www.Camsat.Com service: service@camsat.Com.
