ECCI Trackstar 6000 Series Owner's Manual - page 17

Manual is about: ECCI Trackstar 6000 Series USB HD Ultra driving system

Summary of Trackstar 6000 Series

  • Page 1

    Extreme competition controls inc. - ecci trackstar 6000 series - usb hd ultra - owners manual (edition 3.0 - july 2005) index 1.0 wheel unit setup and adjustment 2.0 pedal unit setup and adjustment 4.0 connecting to your computer 5.0 accessory expansion port 6.0 pot replacement and pot setup trackst...

  • Page 2

    Steering wheel trackstar shift paddle set button center retaining ring button figure 1 - wheel unit components steering unit chassis table mounting bracket figure 2 - wheel unit assembly steering wheel table mounting bracket central chassis structural plate bracket tensioning bolt tensioning pivot t...

  • Page 3

    Trackstar figure 3 - table bracket installation chassis tube bolts bracket mount screw holes figure 4 - table edge mounting and adjustment monitor monitor shelf with 8+ 6 in. 8” m in . Hex key central structural plate inches of clearance remove 2 nuts rear leg adjustment screws elevation of rear leg...

  • Page 4

    Trackstar before and during installation of the wheel make sure that the switch wires are routed through these slots. The wheel screws should be tightened only after verifying the correct position of these wires figure 5 - wheel and paddle set installation center logo steering unit button wheel moun...

  • Page 5

    Figure 6 - steering unit layout figure 7 - usb hd-ultra r6000.1 board layout potentiometer header usb terminal header system logic chips digital button header jumper j-1 4 - button mode 8 - button mode mounting screws trackstar steering potentiometer hi-def usb circuit board accessory expansion port...

  • Page 6

    Trackstar pot cartridge pedal arms pedal pads figure 8 - pedal unit components base assembly pedal frame assembly diagonal struts base assembly figure 9 - assembled pedal unit - side view pivot a pedal tension adjusters angle adjustment pivot b slot pivot c pivot bolts, nuts & washers heel rest heel...

  • Page 7

    Trackstar figure 10 - pedal frame / base assembly pivot a pivot b step 1 step 2 figure 11 - pivot a - two pedal unit bolt installation step 1 step 3 step 2 step 4 pedal frame finger tight only pivot d figure 12 - pivot d - bolts adjustment screws figure 13 - heel rest step 1 pedal frame struts step ...

  • Page 8

    Trackstar figure 14 - removing the pot cartridge 1 3 5 2 4 6 step 1 8 3 5 pmb pivot bolt pot cartridge & pmb exploded view rear view step 3 pmb cam plate pot cartridge pmb cam plate pot cartridge pmb pivot bushing 7 8 6 step 2 pmb spring bracket 9 9 7 step 4 1 2 4 pot cartridge 3.4 steering spring r...

  • Page 9

    Rotation from center 0 240 -240 r es is ta n c e fo r c e 0 m a x minimum preload rotation from center 0 240 -240 r es is ta n c e fo r c e 0 m a x maximum preload outer middle inner 140 lb. 173 lb. 197 lb. 197 lb. 24 lb. 57 lb. 116 lb. 2.0 turns max preload 2.0 turns max preload 2.5 turns max prelo...

  • Page 10

    Trackstar figure 15 - pmb ii pressure brake system pedal pads pivot c main pressure preload adjustment screw and locknut view from left side of brake pedal adjustment screw brake pedal arm rear spring seat and locknut pmb cam plate and mounting bolt main pressure spring slotted black disc pmb cam pl...

  • Page 11

    Figure 18 - pedal potentiometer wire connections [hi-def] gas pedal pot all potentiometers viewed from back side direction of pot rotation a c b cable ground attachment p o t t er m in a ls direction of pot rotation f d e clutch pedal pot direction of pot rotation g i i h brake pedal pot (non-pmb un...

  • Page 12

    240 degrees travel 200 degrees travel 180 degrees travel 220 degrees travel figure 22 - upper lower preload adjuster upper spring seat monopoint spring assembly lower spring retainer cam follower roller resistance cam hex key trackstar monopoint ii monopoint ii spring retention details preload lock ...

  • Page 13

    Linked mode emulates a simple two-axis joystick. Some titles will only run in this mode. Steering acts on the joystick x-axis and gas and brake pedals work in opposite directions on the ‘y-axis’. Linked mode is simple to activate. 1. Disconnect the usb plug from the computer and wait ten seconds. 2....

  • Page 14

    1. Now finish calibrating the remaining controls and go to into your simulation program. If the program uses the windows direct-x calibration information directly, no further calibration is required, just go out on the track and drive. 2. If the program requires its own calibration (i.E. Nascar 2003...

  • Page 15

    Flds figure 26 - fluid damped steering system figure 27 - damping adjustment options drive belt drive pulley damper pulley damper belt tensioning slots flds rotary fluid damper standard light lightest resistance cam, follower arm, and spring assembly removed damper pulley from this view for clarity ...

  • Page 16

    Figure 29 - pedal potentiometer replacement trackstar figure 28 - steering potentiometer replacement steering pot pot bracket screws pot mounting bracket pot retaining nut and lock washer steering pot connector rear chassis plate steering shaft terminus steering shaft clamping screw pot shaft clampi...

  • Page 17

    1. Begin by removing the pmb pivot bolt that holds the cam plate onto the shaft [step 1]. You will need two 9/16-inch wrenches to do this. Remove the cam plate, spring, and hardware. Pot cartridge removal is next. 2. Next remove the screws attaching the pmb spring bracket [step 2]. Once this is remo...

  • Page 18

    9 8 5 4 3 7 1 2 6 figure 30 - db-9 port pin-outs common #5 button #2 button #4 button #3 button #1 common #1 common #3 common #2 common #4 trackstar trackstar figure 31 - button accessory panel electrical schematic db-9 connector figure 3 - switch connection illustration with detail button #1 button...