Ecomax 402 Installation And Operation Instructions Manual

Manual is about: Glass and Dishwashers

Summary of 402

  • Page 1

    Starting from serial no.: glass and dishwashers installation and operation instructions (original instructions) rev. 05.10.2015 8663 4000 ecomax 402/452/502 (incl. Australian 452-90/502).

  • Page 2: Important Notes

    2 05.10.2015 ba-21907-006-en en important notes use in accordance with regulations the machine is technical work equipment for express use in the work place. The machine is exclusively to be used to wash ware such as plates, cups, glasses, cutlery, trays etc. Do not use for electrically heated cooki...

  • Page 3: Contents

    Ba-21907-006-en 05.10.2015 3 en contents page 1. Installation ...........................................................4 1.1. Location .............................................................................................4 1.2. Electrical connection.............................................

  • Page 4: Installation

    4 05.10.2015 ba-21907-006-en en 1. Installation 1.1. Location low temperatures during transport/stocking may lead to dam- age of water containing components. Before installing the machine it should be exposed to normal room temperature (min. 15°c) for 24h. – rear wall clearance not required. – level...

  • Page 5: 1. Installation

    Ba-21907-006-en 05.10.2015 5 en 1.3. Water connection attention: property damage the use of old hose sets for connection to the water supply facility can cause water damage. The included connection hose must be used for connection to the water supply facility. Old hose sets cannot be reused. Connect...

  • Page 6: Controls

    En 6 05.10.2015 ba-21907-006-en 1 8 3 5 4 7 6 2 2 70 65 60 55 50 45 85 80 75 70 65 60 2. Controls ➀ machine on/stop button pushing this button switches the machine on. The led lights up − flashing = machine is filling and heating − permanent = machine is ready in case of operating error or faults, i...

  • Page 7: Start-Up

    Ba-21907-006-en 05.10.2015 7 en 3. Start-up attention: the maximum suction head of the dosing pumps is 1.5 m. Do not confuse the containers. Use only detergent and rinse aid for commercial applications. Please pay attention to the manufacturer’s safety instructions. Changing the chemical products re...

  • Page 8: 3. Start-Up

    8 05.10.2015 ba-21907-006-en en 3.3. Priming the suction hoses attention: the machine has to be switched off. – open the door. – push program buttons ➁ simultaneously. • leds light up. • in display ➇ , the leds 1 and 11−20 illuminate (dependent on basic setting). – push program button “1” repeatedly...

  • Page 9: 3. Start-Up

    Ba-21907-006-en 05.10.2015 9 en 3.4. Softener (optional) note: for the first run, the softener has to be filled with regenera- tion salt and potable water. Attention: filling the salt reservoir with cleaning agent will damage the water softener. – open the door. – unscrew the softener lid and fill t...

  • Page 10: Operation

    10 05.10.2015 ba-21907-006-en en 4.1. Preparation – check correct position of wash/rinse arms, strainer and overflow pipe. – open shut-off valve. – switch on main switch or put the plug in. – check level of detergent and rinse aid containers. – close door and push the on button ➀ • tank will be fill...

  • Page 11: 4. Operation

    Ba-21907-006-en 05.10.2015 11 en 4. Operation 4.2. Run – machine without doser: cleaner enter into the tank. – put rack into the machine and close the door . – start the program by pressing the desired program button 1 or 2. Button "1" = short cycle button "2" = standard cycle • the program button l...

  • Page 12

    12 05.10.2015 ba-21907-006-en en 5. Switch-off and cleaning the machine 5.1. Switch-off – versions with overflow pipe: remove – close the door. – push and hold (min. 3 seconds) the drain button ➂ • led lights up. The self-cleaning cycle will be started and the machine interior is cleaned automatical...

  • Page 13: Settings

    Ba-21907-006-en 05.10.2015 13 en 6.1. Open setting menu attention: the machine has to be switched off. – open the door. If the door is closed or if no button is pressed for 30 seconds, the indicator automatically switches off and the new settings will be saved.Therefore the setting procedure can be ...

  • Page 14: 6. Settings

    14 05.10.2015 ba-21907-006-en en 6.4. Adjustment of water hardness note: to enter the menu for setting the softener, see section 6.1. (previous page). Note: – with optional softener only. – to adjust the softener to the local water hardness (obtain details from local water authority: – push program ...

  • Page 15: Frost Prevention

    Ba-21907-006-en 05.10.2015 15 en this should be carried out by service personnel! In case of frost or longer operation pauses (e.G. For seasonal operations) the machine must be completely drained. Reset for operation according to section 3. 7. Frost prevention.

  • Page 16: Maintenance

    16 05.10.2015 ba-21907-006-en en in order to maintain the warranty, as well as a permanently safe, efficient, and trouble-free operation of the machine, the required maintenance must be carried out by authorized service technicians. For this reason, we recommend the conclusion of an inspection and m...

  • Page 17: Troubleshooting Guide

    Ba-21907-006-en 05.10.2015 17 en 9.1. Poor wash result type of failure possible cause remedy washware are not clean. Wash arms stiff (you should be able to turn them easily by hand). Take out wash arms and clean them thoroughly. Check water outlet from machine to wash arms is clear. Wash arm nozzles...

  • Page 18: Troubleshooting Guide

    18 05.10.2015 ba-21907-006-en en 9.2. Other faults type of failures possible cause remedy glasses are totally or partially cloudy surface of glasses is rough and porous, this is called glass corrosion this is not caused by a malfunction on the machine. Replace with new glasses. Glass breakages. Use ...

  • Page 19

    Ba-21907-006-en 05.10.2015 19 en.

  • Page 20

    20 05.10.2015 ba-21907-006-en hobart gmbh robert-bosch-str. 17 77656 offenburg tel. +49(0)781.600-0 fax +49(0)781.600-23 19 e-mail: info@hobart.De internet: www.Hobart.De as continued product improvement is a policy of hobart, specifications are subject to change without notice. Printed in germany.