1. DL manuals
  2. FPV Model
  3. Drones
  4. X-RACER KL-EX90
  5. Installation Instructions Manual

FPV Model X-RACER KL-EX90 Installation Instructions Manual

Summary of X-RACER KL-EX90

  • Page 1

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com x-racer kl-ex90 installation instructions fpv model limited.

  • Page 2

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com step 1 ： check all the parts in case there’s any missing. 1 x kl-ex90 frame 4 x dragonfly mc1105 7500kv micro class racing motor 1 x flycolor raptor s-tower 1 x runcam micro swift fpv camera 1 x dranonfly5.8g25mw 48ch 8 (pairs) x ...

  • Page 3

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com step 2 ： the wire lengths that you need to keep after cutting. Please keep 35mm motor wires, including the heat shrinkable tubes, as well as 45mm 3-pin camera wires, 40mm vtx wires, 35mm led wires and 60mm power cables. See the pi...

  • Page 4

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com step 3: soldering on flight controller. Solder the pads that are circled in red..

  • Page 5

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com step 4: solder the power cables. Step 5: solder the 3-pin camera wires. Recommend to solder the wires through the flight controller and esc, so as to avoid the possible short circuit in hard crashes. After soldering:.

  • Page 6

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com step 6: solder the vtx wires. Take cautions to the three soldering pads: v+, cam and gnd. If not soldered correctly, the vtx may not work or be burned. Step 7: solder led wires. Before soldering, please make sure the temperature i...

  • Page 7

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com step 8: solder the led wires to flight controller. Step 9: add protective coating onto the vtx. It is not necessary. But adding a layer of protective coating will prevent the vtx from moisture ingress, while still easy for the use...

  • Page 8

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com step 10: solder the vtx to flight controller the vtx positive pole and camera use the same 5v pad. Step 11: solder the motor wires to esc’s you’ll just need to change the position of the three-phase of the first and fourth motors....

  • Page 9

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com step 12 ： install electronics onto the frame pay attention to the different types of screws. M2*10 scres are used to secure 3d printed parts and the top & bottom plate. M2*4 screws are used to secure the dragonfly motors. Each mot...

  • Page 10

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com pay attention to the negative and positive of vtx. The side with led needs to be facing up. Led taillight is secured inside the slot of 3d printed part, no extra screw glue needed..

  • Page 11

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com step 13: installing the frame install the led as below:.

  • Page 12

    Step 1 downlo basic s th por ma sy the m configu in sue. 14: betafl oad betaflig settings as fo he receiver t rt of fc, ac ake sure the stem confi maximum va uration can http:/ light conf ght app thr follows ： that uses sb tivate the op e configurat iguration alue of gy be up to du fp //www.Fpvmod f...

  • Page 13

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com.

  • Page 14

    14: re 2s roll pitch yaw tpa 0. 3s roll pitch yaw tpa 0.2 testing ecommen 450mah p 48 i 5 h p 53 i 55 p 67 i 5 12 450mah p 24 i 48 h p 35 i 50 p 70 i 48 2 g if the mot http:/ nded pid pid settin 50 d 29 5 d 27 8 d pid settin 8 d 18 d 23 d tor turns in fp //www.Fpvmod settings: ng: ng: n correct di p...

  • Page 15

    Fpv model limited http://www.Fpvmodel.Com e ‐ mail:sales@fpvmodel.Com step 15: install the propellers step 16: the build is done! Congratulations! You’ve sucessfully built your own micro racer and now you can start to enjoy the fpv with kl-ex90..