Summary of 6160EX
Page 1
6160ex keypad user instructions.
Page 2: Contents
2 contents glossary .....................................................................................3 introduction ...............................................................................4 day mode, full setting and unsetting .....................................5 part and night setting ...
Page 3: Alarm:
3 glossary the following terms will be used in this manual: alarm: a panel detection circuit has been tripped. Cancel: the action of stopping an alarm condition. Keyfob: a remote control device for setting and unsetting. Each fob will belong to a user. Keytag: a tag or card which can be used for set...
Page 4
4 introduction your galant panel has various system functions, which can be accessed by one of three methods: • type a user code at a keypad • press a button on an rf keyfob or • present a keytag to a proximity reader. The system can support up to 8 users. User 1 is assigned as the master user. Each...
Page 5: Full Setting The System
5 day mode, full setting and unsetting day mode is the normal mode for the system. In this state the display will be similar to that shown on the right, with the time and date. Full setting the system to full set the system (keypad) 1. Type your user code. 2. Press 1 (full) a constant exit tone will...
Page 6: To Unset The System (Keyfob)
6 unsetting the system from any set state to unset the system (keypad) 1. Proceed to the keypad via the approved route. A pulsed tone will indicate that the entry timer is counting down. 2. Type in your user code at the keypad before the expiry of the entry time. The tones will stop and the keypad w...
Page 7
7 part and night setting it is possible to set the system but leave certain detectors switched off. This is useful, for example, at night while the bedrooms are occupied, or when leaving pets within the premises. Your installer can set up these detectors. To part set the system, proceed exactly as f...
Page 8: Installer Resets
8 cancelling alarms if an alarm activation is in progress, whether the system is set or unset, proceed directly to the keypad and type in your user code. This will cancel the alarm condition and the display will show the source of the alarm. Typically, this will be the detection zone that caused the...
Page 9
9 viewing the event log the galant alarm panel has an event log history that records every event which occurs on the system. This includes setting, unsetting, alarm activations and fault conditions. To view the event log: 1. Type in your user code. 2. Press the # key then 0 (log). 3. The display wil...
Page 10
10 omitting zones from the system. To allow flexibility, you can temporarily disable individual detection zones. This is called ‘omitting’. Once a zone is omitted, it will be disabled for the duration of the next set period. When the panel is next unset, the zone will be enabled again. To omit any z...
Page 11
11 chime the chime function allows you to set up a zone to cause a chime tone to activate on the internal sounder and keypad, every time a particular zone is opened. This is particularly useful to warn if a door has been opened. To set up a zone for chime: 1. Type in your user code. 2. Press 9 (chim...
Page 12: Adding Keyfobs
12 adding and removing keyfobs. The keyfobs used on this system employ high security keeloq tm rolling code encryption to make them virtually impossible to duplicate. Adding keyfobs with the system in day mode at the keypad: 1. Enter master user code, 8 (code), and user number (1-8). 2. Wait for dou...
Page 13: Note:
13 6. After second double beep the card has been added successfully. Note: if at any time a triple bleep is heard, the learn procedure has failed. Removing keytags any keytag can be removed from the system as follows: 1. Enter master user code, 8 (code), and user number (1-8). 2. Wait a couple of se...
Page 14: Key Output
14 user descriptors each user code on the system can have a 6-character tag assigned. This tag or descriptor makes it easy to identify users who accessed the system when viewing the event log. User descriptors are entered in a similar way to entering sms text messages on mobile phones. To change the...
Page 15
15 testing the system a test function is available which allows a user to manually test the sensors and alarm sounders on the system. This test is carried out as follows: from normal day mode; 1. Type in the user code. 2. Press 5 (test) 3. The system will ring the outside bells for 5 seconds and swi...
Page 16: Keypad Display
16 system indications in addition to the displays shown previously, the following fault displays may appear on the keypad. If the fault cannot be rectified, please contact your installer, explaining the exact detail on the display. Keypad display meaning tamper zn:xx a tamper fault has occurred on t...
Page 17: Function Button
17 hotkeys hotkeys are key combinations on the keypad that can cause an instant alarm condition. Both keys must be pressed simultaneously to activate the alarm. Hotkeys can be enabled or disabled by your installer. The following hotkey functions are available: function button combination panic alarm...
Page 18: Zone Location
18 zone information zone location full part night 1 2 3 4 5 6 7 8 9 10 11 12 iu1-1233 rev 1.2.