Gallo Tech GStarter I Operation & Installation Manual

Manual is about: Push Button Start & Alarm System With 2 Remote Key FOBs

Summary of GStarter I

  • Page 1

    © copyright gallo technologies . All right reserved - 1 - 52008 operation & installation manual for: push button start & alarm system with 2 remote key fobs disclaimer: this installation manual is designed for the installer or individual with an existing understanding of automotive electrical system...

  • Page 2

    © copyright gallo technologies . All right reserved - 2 - 52008 the has been designed to function in any vehicle (carbureted, fuel injected, diesel, automatic or manual transmission, and locking or non-locking steering column.) if your vehicle has a factory installed security system with or without ...

  • Page 3

    © copyright gallo technologies . All right reserved - 3 - 52008  data bus systems 2003 and newer gm trucks/suv’s, ‘96-04 jeep grand cherokee data bus systems send low current “data messages” to the door lock controllers on a network in order to lock and unlock the vehicle. To install aftermarket sy...

  • Page 4

    © copyright gallo technologies . All right reserved - 4 - 52008 c.) lock only by remote:  when the ignition key is on, pressing will lock the doors and the system will remain in the disarmed mode. Siren button: car-locating/anti-hijack a.) car locating  when the system is armed, holding this butto...

  • Page 5

    © copyright gallo technologies . All right reserved - 5 - 52008 lock/unlock siren chirp: if this option is set to disable the siren will not chirp when locking and unlocking the doors. Two pulse locking / unlocking: when pressing or the electrical pulse sent to the door locking/unlocking mechanism c...

  • Page 6

    © copyright gallo technologies . All right reserved - 6 - 52008 table 1: function option chart parking lights flash 3 times or 1 time to indicate the function state “engine start” button off/on n th times function to set parking lights flash 3 times parking lights flash 1 time 1 time * valet mode di...

  • Page 7

    © copyright gallo technologies . All right reserved - 7 - 52008 when installing as a stand alone “engine start” only configuration, the only wires that must be connected are those marked with an ( * ) see fig. 1 for location and identification of control module connectors. 4 pin wire harness (engine...

  • Page 8

    © copyright gallo technologies . All right reserved - 8 - 52008 figure 1 c1, r1/r2: 4 pin wire harness and relay pair (engine start circuit) figure 2 6 pin wire harness (door lock/unlock circuit) used for “engine start with alarm” configuration only determine the door locking/unlocking circuitry tha...

  • Page 9

    © copyright gallo technologies . All right reserved - 9 - 52008 year diagrams can be found on our web site at www.Gallotech.Com) if the trigger wire is 0v when the lock/unlock switch is depressed then you have a neg. (-) trigger (fig. 4). If the trigger wire is +12v when depressing the lock/unlock s...

  • Page 10

    © copyright gallo technologies . All right reserved - 10 - 52008 figure 6 figure 7 7 pin wire harness (parking lights, siren, foot brake and door trigger circuit) note: connect c3: red, c3: pink and c3: black wires for stand alone “engine start” only configuration. Connect all wires when installing ...

  • Page 11

    © copyright gallo technologies . All right reserved - 11 - 52008 c3: 7 pin wiring harness diagram figure 8 3 pin wire harness (engine start button) the engine start button can be surface mounted in a convenient location on the dash or can be mounted using the supplied adjustable bracket for mounting...

  • Page 12

    © copyright gallo technologies . All right reserved - 12 - 52008 engine cranks but will not start: check ignition switch wiring. The ign 1 wire must not be cut. The only wires connected to this wire should be the red start input +12 v from connector c1 and the c3 pink wire. Some vehicles require 2 s...