Gamma 600 Owner's Manual

Summary of 600

  • Page 1

    600 / 600fc owner's manual issue 2 / version e - dec. 10, 1997 progression copyright 1997 gamma sports - all rights reserved provided by www.Gssalliance.Com.

  • Page 2: Limited Warranty

    1 table of contents page 1 ................................................................................................ Warranty page 2 ................................................................................................... Features page 3 ...............................................

  • Page 3

    2 features drop weight tensioner w/ 8lb. To 90lb. Range and permanently engraved weight scale professional six point mounting system w/ l-shaped frame shoulder clamps - accomodates all racquets without adapters patented parallel jaw rotating ratchet gripper w/ diamond dust coated gripping surfaces -...

  • Page 4

    3 assembly instructions installing the turntable the turntable is located under the foam packing in the bottom of the shipping carton. Insert the center post of the turntable into the bushing of the stringing machine base. Engaging the drop weight bar stop the stringing machine is shipped with the d...

  • Page 5

    4 mounting the frame adjusting the frame support posts place the racquet frame over the center posts and onto the frame support. Loosen the lever lock bolt on one support post. Slide the post outward until the center support of the racquet support slide is positioned near the inside surface of the r...

  • Page 6

    5 stringing the frame the drop weight is of a two piece design. When assembled, it will accomodate ten- sions from 20 lbs. To 90 lbs. For tensions from 8 to 20 lbs., remove the 5mm bolt on the face of the drop weight, and use the smaller portion of the weight as described above. Note: tensions above...

  • Page 7

    6 stringing the frame gripping the string while holding the tension bar slightly above horizontal, wrap the free string clockwise around the gripper drum once and position between the gripper jaw. Gently turn the gripper clockwise while squeezing the jaws together until all slack in the string is re...

  • Page 8

    7 stringing the frame clamping the string clamp the tensioned string to the next adja- cent string using the second string clamp. Release the string from the gripper by raising the tension arm. Repeat the procedure for all of the remaining main strings and tie off following the racquet manufacturers...

  • Page 9

    8 pathfinder awl the gamma 600 includes the new pathfinder stringing awl which creates a pathway between or around strings to make inserting a string through tight gromets easier and quicker. Insert the awl through the grommet hole in the same manner as for traditional awls. The pathfinder awl must ...

  • Page 10

    9 fixed clamp upgrade fixed clamp installation to install the clamps, remove the winged lock knob to separate the knob from the lower guide bushing. Be careful not to lose the radial thrust bearing components located in the center recess of the knob. Align the clamp base with the clamp slot of the t...

  • Page 11

    10 fixed clamp operation fixed clamp operation the fixed clamps for the gamma 600 are of a dual action design. The string clamp and the clamp base operate independently of one another. To clamp a string, lift the clamp head and place the string between the jaws. Depress the clamp head lever to secur...

  • Page 12

    11 maintenance your gamma 600 stringing machine is adjusted for optimum performance at the factory and needs no further adjustments before use. After extensive use however, the machine may need minor adjusments as follows : adjusting the turntable bushings there are two adjustment points on the mach...

  • Page 13

    12 parts list part # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 17 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 39a description aluminum base base cover tray pad turntable bushing rubber feet cap screw foot nut bushing set screw washer winder stand turntable turntable pin post lock lever washer...

  • Page 14

    13 exploded parts view.

  • Page 15

    14 mounting stand parts 143 140 141 145 144 part # 9 13 14 15 21 22 23 24 140 description washer - m8 post locking lever washer - m10 support post frame support slide badminton adapter tennis adapter support slide knob mtng. Stand top plate part # 141 142 143 144 145 146 147 148 description mtng. St...