IAdea XDS-1060 User Manual - 6. Technical Data

Manual is about: IAdea Interactive Digital Signboard User's Manual

Summary of XDS-1060

  • Page 1

    Xds-1060/1062 user’s manual notes about model variants the xds-1060 and xds-1062 models are based on xds-1060 with the following differences: xds-1060 ethernet + wi-fi xds-1062 power over ethernet + wi-fi power over ethernet applies to xds-1062 only. All other aspects of operation are identical for ...

  • Page 2: Contents

    I contents xds-1060/1062 user’s manual 0 1. Introduction 1 1.1. Features 1 1.2. Package contents 1 1.3. Physical view and features 1 1.4. Installation 2 2. Configuring the xds-1060/1062 digital signboard 3 2.1. System connections 3 2.2. Basic settings 4 2.3. Connect the xds-1060/ 1062 to your networ...

  • Page 3: 1. Introduction

    1 1. Introduction this document describes the hardware and software operations of the xds-1060/1062 system set up, and frequently asked questions. 1.1. Features 10-inch widescreen lcd display and stereo speakers 4gb on-board flash local storage with sd card slot built-in motion sensors and 6 touch b...

  • Page 4

    2 1.4. Installation fix the display stand 1 put the supplied display stand onto the screw socket. 2 insert the two supplied screws. 3 fasten the screws. Fix the kensington lock 1 press kensington lock’s button and aim at the lock hole. 2 plug the lock into the lock hole, and then lose the button. Op...

  • Page 5

    3 2. Configuring the xds-1060/1062 digital signboard 2.1. System connections 1 attach the ac power adapter to power on the unit. After approximately 35 seconds booting animation will be displayed on screen as shown below : 2 player boot process takes approximately 60 seconds to complete. After boot ...

  • Page 6

    4 basic settings allow user to configure the 3 important settings to signage application – network, time zone and content. Each time user enter basic settings menu, signboard will start playback automatically after 15 seconds if user already set content services previously. Auto playback can be canc...

  • Page 7

    5 (fig. 2.3.3) 4 click on the station name to connect. If the network requires authentication, you will be asked to provide the password for access. (fig. 2.3.4) wired connection to use the wired ethernet connection, connect an ethernet cable and disable the wireless lan interface first 1 clickthe w...

  • Page 8

    6 static ip – manually assign network ip address 4 click the ethernet to make static ip configuration. (fig. 2.3.6) 2.4. Time zone settings 1 clickthe time zone , configuration menu will be launched. (fig. 2.4.1) 2 choose the correct time zone from available options. (fig. 2.4.2).

  • Page 9

    7 2.5. Content settings 1 click the set content button, configuration menu will be launched. (fig. 2.5.1) 2 input the content source url and click connect button, signboard will start playback immediately. (fig. 2.5.2) 2.6. Player information user can check the signboard’s basic information includin...

  • Page 10

    8 2 click on information. The definitions of the health status: green – normal. The device connects to the url server of the content source normally. Blue – local. The device plays the contents from the usb drive or sd card. Gray – disconnected. The device is in the disconnection state. (fig. 2.6.2)...

  • Page 11

    9 (fig. 2.8.1) 2.9. Content configuration – easyplay the feature easyplay allows the signboard to play the media contents from the usb flash drive (or sd card) directly. When easyplay is enabled, the signboard will play the contents from the usb drive (or sd card) only. If user wants to play the con...

  • Page 12

    10 (fig. 2.9.2) configure movie mode 6 clickon movie for choosing movies. Click on the button as marked in red below, and select the movie directory from the usb drive. 7 click set button after the folder is selected. 8 the files in the selected folders will be played while clicking on the play butt...

  • Page 13

    11 (fig. 2.9.4) 4 the "on" time assigned in the time slots a-e are inclusive. For example a schedule assigned as the figure below, (fig. 2.9.5) the exact playback time will be the time slots marked in blue as shown in figure 2.9.6. The dark blue parts are the overlap time of c/d and d/e. (fig. 2.9.6...

  • Page 14

    12 2.10. Display settings output mode the default output mode is set to ‘panel’ with resolution 800 x 480. (fig. 2.10.3) if you are connecting to a monitor via the hdmi port, refer to the device specification for the best matching setting. Please note that the signboard supports only one output devi...

  • Page 15

    13 (fig. 2.10.3) panel brightness the default panel brightness is set to maximum, and it can be adjusted in the display settings. 1 click the advanced button, advanced configuration menu will be launched. (fig. 2.6.1) 2 click the display/sound button, and then click on display. The display settings ...

  • Page 16

    14 screen orientation screen orientation is to set the display to rotate 90/180/270 degrees. 1 click the advanced button, advanced configuration menu will be launched. (fig. 2.6.1) 2 click the display/sound button, and then click on display. The display settings page will be launched. (fig. 2.10.1) ...

  • Page 17

    15 (fig. 2.11.1) 3 click on volumes, the volumes settings page will be launched. Drag the blue dots to adjust the volumes for the selected item, and then click on ok to save the new settings. (fig. 2.11.3) 4 clickon the checkbox on the right as marked in red to enable/disable the touch sounds. (fig....

  • Page 18

    16 3 click the enable daily reboot button as marked in red below to enable/disable the daily reboot function. Click on the dialogue box to set the time. The value can be input by using the pop-up keyboard or the usb keyboard. 4 click on set to save the setting. (fig. 2.12.1) 2.13. System configurati...

  • Page 19

    17 (fig. 2.13.2) 2.14. System configuration - factory reset if you forget a system password you have set, you must reset the system to regain access to the signboard. Using the reset button 1 press and hold the reset button with a pen. 2 re-connect the power cord. 3 wait about 16 seconds or until th...

  • Page 20

    18 2.15. System configuration – power save the feature power save allows the signboard to power off automatically while stopping at the basic settings page without any action is been taken for 10 minutes. 1 click the advanced button, advanced configuration menu will be launched. (fig. 2.6.1) 2 click...

  • Page 21: 3. Content Management

    19 3. Content management the xds-1060/1062 is designed to work with 3 rd party management solutions. Please refer to the printed guide for related set up instructions. 4. Authoring in html5 a major advancement in the xds-1060/1062 digital signboard is the ability to playback html5 content which can ...

  • Page 22: 6. Technical Data

    20 6. Technical data 6.1. Specifications xds-1060 xds-1062 video format support popai screen media standards s6 (mpeg-1 sif, 3mbps cbr) s7 (mpeg-1 480p, 10mbps cbr) s8 (mpeg-1 720p, 15mbps cbr) s9 (mpeg-2 480p, 6mbps cbr) s10 (mpeg-2 720p, 12mbps cbr) s11 (mpeg-4 avc, 480p, 6mbps cbr) s12 (mpeg-4 av...

  • Page 23: 7. Appendix: Faq

    21 7. Appendix: faq what video format can i play? Video files encoded in mpeg-4 avc up to 1920x1080 resolutions and 10mbps bitrates should play perfectly. If a certain video is not played as scheduled, or if it plays poorly, please search the support site for “transcode” instructions. The signboard ...

  • Page 24

    22 the signboard is not playing. What should i do? Play list errors and scheduling issues are two major causes of playback problems. To determine if the problem is caused by a bad play list, just delete the play list and restart signboard. The signboard should loop through all media files, indicatin...

  • Page 25: Iadea Limited Warranty

    23 iadea limited warranty for media player devices applicable to iadea product models: xds-1060/1062 1. Iadea provides, unless extended through optional service programs, one (1) year of limited warranty on its applicable product models listed above. The applicable product must be purchased through ...