IBM 2626HNU - ThinkPad 390X 2626 User Manual - Fn Key Combinations

Manual is about: IBM ThinkPad 390X: User Guide

Summary of 2626HNU - ThinkPad 390X 2626

  • Page 1

    I.

  • Page 2

    Before using this information and the product it supports, be sure to read the general information under “read this first” on page 19. First edition (november 1999) the following paragraph does not apply to the united kingdom or any country where such provisions are inconsistent with local law: inte...

  • Page 3: Contents

    Contents thinkpad 390x / i series 1700 hardware maintenance manual . . . . . . . . . . . . . . 1 introduction . . . . . . . . . . . . . . . . . . . . 2 important service information . . . . . . . . . . 2 how to use error messages . . . . . . . . . . 3 how to read post error messages . . . . . . 3 dr...

  • Page 4

    Writing the rfid data . . . . . . . . . . . . . 47 flash uuid . . . . . . . . . . . . . . . . . . 47 running the diagnostics . . . . . . . . . . . . . . 48 pc-doctor dos system diagnostics . . . . . . 48 fru removals and replacements . . . . . . . . . 58 fru service procedures . . . . . . . . . . . ...

  • Page 5

    Notices . . . . . . . . . . . . . . . . . . . . . 119 trademarks . . . . . . . . . . . . . . . . . . 119 contents v.

  • Page 6

    Vi thinkpad 390x / i 1700 hmm.

  • Page 7

    Thinkpad 390x / i series 1700 hardware maintenance manual about this manual this manual contains service and reference information for the ibm thinkpad 390x / i series 1700 products. Use this manual along with the advanced diagnostics tests to trou- bleshoot problems effectively. The manual is divid...

  • Page 8: Introduction

    Introduction important service information important diskette fixes are customer installable. Advise customers to contact the pc company helpcenter at 800-772-2227 if they need assistance in obtaining or installing any diskette fixes. Customers in canada should call ibm helppc at 800-565-3344 for as...

  • Page 9

    Hard disk drive replacement strategy: always try to run a low-level format before replacing a hard disk drive. Attention the drive startup sequence in the computer you are servicing might have been changed. Be extremely careful during write operations such as copying, saving, or formatting. Data or ...

  • Page 10

    Drive and diskette compatibility matrix the following table provides identification information for 3.5-inch drives. Diskette drive identifying mark 3.5-inch - 1.44mb 1.44 on the eject button 3.5-inch - 2.88mb 2.88 on the eject button the following table provides compatibility information for 3.5-in...

  • Page 11: Translations)

    Safety notices (multi-lingual translations) in this manual, safety notices appear in english with a page number reference to the appropriate multi-lingual, translated safety notice found in this section. The following safety notices are provided in english, french, german, italian, and spanish langu...

  • Page 12

    Safety notice 2 some standby batteries contain a small amount of nickel and cadmium. Do not disassemble it, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regu- lations. Use only the battery in the appropriate parts listing. U...

  • Page 13

    Safety notice 3 the battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short- circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pa...

  • Page 14

    Safety notice 4 the lithium battery can cause a fire, explosion, or severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°c (212°f), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations...

  • Page 15

    Safety notice 5 if the lcd breaks and the fluid from inside the lcd gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau d'affichage à cristaux liquides ...

  • Page 16

    Safety notice 6 to avoid shock, do not remove the plastic cover that surrounds the lower portion of the inverter card. Afin d'éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d'alimentation. Aus sicherheitsgründen die kunststoffa...

  • Page 17

    Safety notice 8 before removing any fru, power-off the computer, unplug all power cords from electrical outlets, remove the battery pack, then disconnect any interconnecting cables. Avant de retirer une unitˆ rempla†able en clientèle, mettez le système hors tension, débranchez tous les cordons d'ali...

  • Page 18: Safety Information

    Safety information the following section contains the safety information that you need to be familiar with before servicing an ibm mobile computer. General safety follow these rules to ensure general safety: observe good housekeeping in the area of the machines during and after maintenance. When lif...

  • Page 19: Electrical Safety

    Reinstall all covers correctly before returning the machine to the customer. Electrical safety observe the following rules when working on electrical equipment. Important use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you ...

  • Page 20: Safety Inspection Guide

    Observe the special safety precautions when you work with very high voltages; these instructions are in the safety sections of maintenance information. Use extreme care when measuring high voltages. Regu- larly inspect and maintain your electrical hand tools for safe operational condition. Do not us...

  • Page 21: Handling Electrostatic

    Explosive hazards, such as a damaged crt face or bulging capacitor. Mechanical hazards, such as loose or missing hard- ware. The guide consists of a series of steps presented in a checklist. Begin the checks with the power off, and the power cord disconnected. Checklist: 1. Check exterior covers for...

  • Page 22: Grounding Requirements

    Wear a grounded wrist strap against your skin to eliminate static on your body. Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. Use the black side of a grounded work mat to provide a static-free work surface. The...

  • Page 23: Laser Compliance Statement

    Laser compliance statement some ibm personal computer models are equipped from the factory with a cd-rom drive. Cd-rom drives are also sold separately as options. The cd-rom drive is a laser product. The cd-rom drive is certified in the u.S. To conform to the requirements of the department of health...

  • Page 24

    Puede provocar la exposición a radiaciones peligrosas. Opening the cd-rom drive could result in exposure to hazardous laser radiation. There are no serviceable parts inside the cd-rom drive. Do not open. Some cd-rom drives contain an embedded class 3a or class 3b laser diode. Note the following. Dan...

  • Page 25: Read This First

    Read this first before you go to the checkout guide, be sure to read this section. Important notes only certified trained personnel should service the computer. Read the entire fru service procedures before replacing any frus. Use new nylon-coated screws when you replace frus. Be extremely careful d...

  • Page 26

    Before checking problems with the computer, determine whether or not the damage applies to the warranty by referring to the following: note for warranty: during the warranty period, the cus- tomer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification...

  • Page 27: Service Web Site

    3. Remove the backup battery (rtc) for 20 minutes or use a screwdriver to touch the backup battery (rtc) for 1 second. 4. Put back the backup battery (rtc). 5. Power on the computer and wait until post ends. 6. Verify that the password prompt does not appear. Supervisor and hdd passwords: the superv...

  • Page 28: Product Overview

    Product overview the following shows an overview of the system features of the thinkpad 390x / i series 1700 computer. Feature description processor intel mobile pentium iii processor 500 mhz, l2 cache intel mobile pentium iii processor 450 mhz, l2 cache intel mobile pentium ii processor 400 mhz, l2...

  • Page 29: Fn Key Combinations

    Feature description pc card (pcmcia) one type iii or two type ii cardbus, zv port support ac adapter 56–watt type fn key combinations the following table shows the fn key and function key combinations and their corresponding functions. The fn key works independently of the operating system. The oper...

  • Page 30: Status Indicators

    Status indicators the system status led indicators show the current com- puter status. The following shows the location of each indi- cator symbol and the meaning of each indicator. Symbol color meaning (1) battery status green enough battery power remains for operation. Blinking orange the battery ...

  • Page 31

    Symbol color meaning (5) caps lock green caps lock mode is enabled. All alphabetic characters (a-z) are entered in capital letters without the shift key being pressed. You enable or disable the caps lock mode by pressing the caps lock key. (6) scroll lock green scroll lock mode is enabled. The arrow...

  • Page 32: Checkout Guide

    Checkout guide use the following procedure as a guide for computer prob- lems. Besides the checkout tests described in this section, there are other items you can test for using the pc-doctor dos diagnostics program. See “pc-doctor dos system diagnostics” on page 48 for details. Note: the diagnostic...

  • Page 33: Audio Checkout

    Audio checkout do as follows: 1. Boot from and start pc-doctor dos. (see “pc-doctor dos system diagnostics” on page 48 for details.) 2. Select interactive tests. 3. Select internal speaker. If no sound is played, replace the speaker or the system board. 4. Select stereo speaker. If no music is playe...

  • Page 34: Cd-Rom Checkout

    Cd-rom checkout do the following to isolate the problem to a controller, drive, or cd-rom. Make sure that the cd-rom disc does not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail. Do the following to select the test device: 1. Boot from and start...

  • Page 35: Checkout

    Keyboard and auxiliary input device checkout note: remove the external keyboard if the internal key- board is to be tested. If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable extending from the keyboard is correctly seated in the con- nector....

  • Page 36: Memory Checkout

    Memory checkout dimm are available for increasing memory capacity. Memory errors might stop system operation, show error messages on the screen, or hang the system. Use the following procedure to isolate memory problems: 1. Boot from and start pc-doctor dos. (see “pc-doctor dos system diagnostics” o...

  • Page 37: Modem Board Checkout

    Modem board checkout do the following to isolate the problem to the system internal modem: 1. Boot from and start pc-doctor dos. (see “pc-doctor dos system diagnostics” on page 48 for details.) 2. Select diagnostics. 3. Select other devices. 4. Run modem loopback test and modem dialtone/dtmf test. 5...

  • Page 38: Power System Checkout

    Power system checkout to verify the symptom of the problem power on the com- puter using each of the following power sources: 1. Remove the battery. 2. Connect the ac adapter and check that power is sup- plied. 3. Disconnect the ac adapter and install the charged battery; then check that power is su...

  • Page 39

    Checking the operational charging: to check operational charging, use a discharged battery pack or a battery that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator does not turn on, remove the battery and let ...

  • Page 40: Trackpoint Checkout

    Trackpoint checkout if the external mouse is connected, the trackpoint does not work. In this case, please detach the external mouse to check the trackpoint. If this does not correct the trackpoint problem, continue with the following. After you use the trackpoint, the pointer drifts on the screen f...

  • Page 41: Power Management Features

    Power management features three power management modes are available in the com- puter system to reduce power consumption and to prolong battery life. Standby mode: in standby mode, the following occurs: the lcd backlight turns off. The audio amplifier turns off. (fn+f3) events that cause the comput...

  • Page 42

    The computer also exits suspend mode when timer condi- tions are satisfied for entering hibernation mode. Hibernation mode: for windows nt or os/2 user: a windows nt or os/2 user cannot create a hibernation file in a windows nt or os/2 system that uses the ntfs/hpfs format system. If you want to use...

  • Page 43

    How to create the hibernation function: do as follows: start the thinkpad configuration program. Click on the power management icon. Click on the hibernation options tab. Click on enable hibernation. Click on ok. Note: if you change the memory size, you need to recreate the hibernation file or parti...

  • Page 44: Symptom-to-Fru Index

    Symptom-to-fru index the symptom-to-fru index lists the symptoms and errors and the possible causes. The most likely cause is listed first. Note: perform the fru replacement or actions in the sequence shown in the fru/action columns. If a fru replacement does not solve the problem, put the original ...

  • Page 45: Numeric Error Codes

    Numeric error codes the following is a list of the message that the bios can display. Most of them occur during post. Some of them display information about a hardware device, e.G., the amount of memory installed. Others may indicate a problem with a device, such as the way it has been config- ured....

  • Page 46

    Symptom/error fru/action in sequence 0281 memory size found by post differed from cmos 1. Load setup defaults in the bios setup utility. 2. Dimm 3. System board 02bx diskette drive a error 1. Check that the drive is defined with the proper diskette type in bios setup utility. 2. Go to “diskette driv...

  • Page 47: Error Messages

    Error messages symptom/error fru/action in sequence device address con- flict 1. Load setup defaults in bios setup utility. 2. Backup battery (rtc) 3. System board allocation error for: device 1. Load setup defaults in bios setup utility. 2. Backup battery (rtc) 3. System board failing bits: nnnn 1....

  • Page 48: Lcd-Related Symptoms

    Symptom/error fru/action in sequence no beep, power-on indicator off, lcd blank during post battery ac adapter dc-dc & batt board system board no beep, power-on indicator on, lcd blank during post reseat dimm. Cpu card system board no beep during post but system runs correctly. Speaker lcd-related s...

  • Page 49: Power-Related Symptoms

    Power-related symptoms symptom/error fru/action in sequence power shuts down during operation. 1. Battery 2. Ac adapter 3. Dc/dc & charger board 4. System board the system will not power on. 1. Battery 2. Ac adapter 3. Dc/dc & charger board 4. System board the system will not power off. 1. Press and...

  • Page 50: Intermittent Problems

    Symptom/error fru/action in sequence the system will not wake up from hibernation mode. 1. Keyboard (if control is from the keyboard) 2. Hard disk drive 3. System board the system will not enter suspend mode after closing the lcd. 1. Lid switch 2. System board battery fuel-gauge does not go higher t...

  • Page 51: Undetermined Problems

    When analyzing an intermittent problem, do the following: 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any frus. 3. If any error is detected, replace the fru shown by the fru code.. Rerun the test to verify that n...

  • Page 52: Setting The Lcd Panel Id

    Ce utility program diskette note: you can download the ce utility program diskette from the ibm website. Setting the lcd panel id there is an eeprom in the inverter which stores its sup- ported lcd type id code. If you replace a lcd with one of a different brand or use a new inverter, the id informa...

  • Page 53: Writing The Rfid Data

    Writing the rfid data the eeprom on the system board contains the system unit serial number and the system board serial number. When you replace the system board, restore the system unit serial number using the rfid utility in the thinkpad ce utility diskette. The serial number label is attached to ...

  • Page 54: Running The Diagnostics

    Running the diagnostics pc-doctor dos is used to perform diagnostics on the thinkpad 390x / i series 1700. Pc-doctor dos system diagnostics note: some test items require tools as shown below: diskette drive: erasable 2hd diskette parallel: tri-connector wrap plug (p/n: 72x8546) serial: tri-connector...

  • Page 55

    To use pc-doctor dos: 1. Press the left and right arrow keys to move around the main menu. Press enter to enable the highlighted option. The main options are: diagnostics interactive tests hardware info utility quit 2. Press the up and down arrow keys to move in a selected menu. Press enter to enabl...

  • Page 56

    Pc-doctor dos diagnostics error codes and messages: the following table does not include user-initiated aborts, which display the error type 195. Error code 0-199 fru/action in sequence: backup battery (rtc) system board error code 1-1 to 1-260 fru/action in sequence: system board error code 1-286 t...

  • Page 57

    Error code 5-16 to 15-36 fru/action in sequence: system board error code test(s) message 5-16 video memory pattern failed 5-24 video video page test failed 5-26 video register failed 5-199 video could not initialize mode 13h for register test 11-2 com timeout sending 11-13 com lcr/mcr fail 11-14 com...

  • Page 58

    Error code 18-1 to 18-27 fru/action in sequence: pcmcia holder system board error code 20-1 to 71-41 fru/action in sequence: system board error code test(s) message 18-1 pcmcia no pcmcia detected 18-5 pcmcia incorrect pcmcia version 18-9 pcmcia incorrect number of sockets 18-24 pcmcia index register...

  • Page 59

    Error code 75-1 fru/action in sequence: dc-dc & batt board system board error code 89-250 to 89-294 fru/action in sequence: reload bios default setting cpu card system board error code 170-1 to 175-198 fru/action in sequence: system board error code test(s) message 75-1 ac charger ac charger not sup...

  • Page 60

    Error code 175-199 fru/action in sequence: fan system board error code 175-250 to 185-262 fru/action in sequence: system board error code test(s) message 175-199 fan fan test failed error code test(s) message 175-250 lm75/ max1617 interrupt condition detected 185-1 rfid/ alertpack asset id not suppo...

  • Page 61

    Error code 201-1 to 201-198 fru/action in sequence: dimm system board error code 202-1 to 202-18 fru/action in sequence: system board error code 206-16 to 206-290 fru/action in sequence: reseat diskette drive cable diskette drive system board error code test(s) message 201-1 dimm no smbus detected (...

  • Page 62

    Error code 215-1 to 215-254 fru/action in sequence: reseat cd-rom cable cd-rom drive system board error code 217-14 to 217-262 fru/action in sequence: reload bios default setting hard disk connector hard disk drive error code 301-250 to 301-266 fru/action in sequence: reseat keyboard connector keybo...

  • Page 63

    Error code 304-1 to 304-199 fru/action in sequence: battery pack dc-dc & batt board system board error code 415-1 to 415-250 fru/action in sequence: reseat modem card modem card system board error code test(s) message 304–1 battery no battery installed no battery detected 304–199 battery general bat...

  • Page 64

    Fru removals and replacements this section contains information about removals and replacements. Do not damage any parts. Only certified and trained personnel should service the computer. The arrows in this section show the direction of move- ment to remove a fru, or to turn a screw to release the f...

  • Page 65: Fru Service Procedures

    Fru service procedures review the following procedures before replacing any fru. Lcd fru replacement notice: the tft lcd for the notebook computer contains over 2,359,296 thin- film transistors (tfts). A small number of missing, discol- ored, or lighted dots (on all the time) is characteristic of tf...

  • Page 66

    Torque driver if you have a torque driver, refer to the "torque" column with each step. Make sure you use the correct screw, and tighten all screws firmly to the torque shown in the table if you have a torque screwdriver. Never use a screw that you removed. Use a new one. Make sure the screws are ti...

  • Page 67: Battery

    Battery to remove the battery, press the latch to release, then pull out the battery. 1 2 3 reverse the steps described above when installing a new battery pack. Thinkpad 390x / i 1700 hmm 61.

  • Page 68: Hard Disk Drive

    Hard disk drive warning do not drop or apply any shock to the hard disk drive. The hard disk drive is sensitive to physical shock. Incorrect handling can cause damage and permanent loss of data on the drive. Before removing the drive, have the user make a backup copy of all the information on the dr...

  • Page 69: Combo Bay

    Combo bay to remove the combo bay, press and hold the lock to release, then slide out the combo bay module to remove. Thinkpad 390x / i 1700 hmm 63.

  • Page 70: Diskette Drive

    Diskette drive to remove the diskette drive: 1. Remove the four screws securing the diskette drive as shown. 2. Disconnect the diskette drive cable from the con- nector. Note: lift both sides of the connector. 3. Slide out the diskette drive to remove. Step size (quan- tity) head & color torque 1 m2...

  • Page 71: Cd-Rom

    Cd-rom to remove the cd-rom: 1. Remove the four screws securing the cd-rom. 2. Carefully slide out the cd-rom to remove. Note: watch out for the sharp edges on the cd-rom. Step size (quan- tity) head & color torque 1 m2.5x 4l (4) flat head, silver 1.6 kgf-cm note: make sure you use the correct screw...

  • Page 72: Combo Bay Fpc

    Combo bay fpc to remove the combo bay fpc: 1. Remove the two screws securing the combo bay fpc. 2. Carefully disconnect the combo bay fpc from the connector. 1 2 step size (quan- tity) head & color torque 1 m2.5x 3.5l (2) flat head, black 1.6 kgf-cm note: make sure you use the correct screw for repl...

  • Page 73

    Hard disk adapter combo bay to remove the second hard disk drive from the hard disk drive adapter: 1. Remove the two screws of the combo bay adapter. 2. Slide the hard disk drive out and up to remove. Step size (quan- tity) head & color torque 1 m3 x 5l (2) pan head, black 1.6 kgf-cm note: make sure...

  • Page 74: Modem Card

    Modem card “battery” on page 61 note: never remove or attach the card before removing the battery. To remove the modem card: 1. Use a flat-bladed screwdriver to remove the screw on the modem door. 1 2. Carefully release the latches on both sides of the modem card. 3. Gently pull out the cable from t...

  • Page 75: Backup Battery (Rtc)

    Backup battery (rtc) “battery” on page 61 “modem card” on page 68 safety notice 4: translation on page 8 the lithium battery can cause a fire, explosion, or severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°c (212°f), incinerate it, or expose its cell...

  • Page 76: Keyboard

    Keyboard “battery” on page 61 “hard disk drive” on page 62 to remove the keyboard: 1. Use a 1/8" alignment tool to release the latches to lift the middle cover away. 2. Remove the two screws securing the keyboard. 3. Carefully lift the keyboard up to expose the keyboard connector. Note: be careful o...

  • Page 77

    4. Use a flat-bladed screwdriver to release the cable from the connector. 5. Remove the keyboard from the lower case. Thinkpad 390x / i 1700 hmm 71.

  • Page 78: Led Board

    Led board “battery” on page 61 “hard disk drive” on page 62 “keyboard” on page 70 to remove the led board: 1. Remove the screw securing the led board then dis- connect the led cable from the connector. 2. Lift the led board. 1 2 3 step size (quan- tity) head & color torque 2 m2 x 4l (1) flat head, s...

  • Page 79: Upper Heatsink

    Upper heatsink “battery” on page 61 “hard disk drive” on page 62 “keyboard” on page 70 1 3 2 step size (quan- tity) head & color torque 1 m2.5 x 18l (3) pan head, black 2.0 kgf-cm 2 m2 x 18l (3) pan head, black 2.0 kgf-cm 3 m2 x 4l (4) flat head, silver 1.6 kgf-cm note: make sure you use the correct...

  • Page 80: Pcmcia Slots

    Pcmcia slots “battery” on page 61 “hard disk drive” on page 62 “keyboard” on page 70 “upper heatsink” on page 73 to remove the pcmcia slots: 1. Remove the three screws securing the pcmcia slot board. 1 2 2. Use a flat-bladed screwdriver to disconnect the pcmcia card from the connector. 3 4 3. Carefu...

  • Page 81

    Caution: when reassembling this section of the machine, the upper heatsink must be reassembled first before the pcmcia slots. Thinkpad 390x / i 1700 hmm 75.

  • Page 82: Cpu Board

    Cpu board “battery” on page 61 “hard disk drive” on page 62 “keyboard” on page 70 use the special tool to remove the cpu board. Note: the cpu tool is for depot use only. 1 2 to install the cpu board. Note: when you replace the cpu board, press only on the places indicated in the figure. Press both s...

  • Page 83: Lcd Panel

    Lcd panel “battery” on page 61 “hard disk drive” on page 62 “keyboard” on page 70 to remove the lcd panel: 1. Remove the two screws securing the lcd fpc cable. 2. Remove the lcd fpc cable. Then: disconnect the lcd fpc cable from the lower case (12.1"). Disconnect the lcd fpc cable and lvds board (15...

  • Page 84

    Step size (quan- tity) head & color torque 2 m2.5 x 18l (1) m2 x 10l (1) pan head, black pan head, silver 15.1" and 14.1" l:1.6 kgf-cm r:1.6 kgf-cm 3 m2.5 x 6l (4) flat head, black 4.0 kgf-cm note: make sure you use the correct screw for replacement. 78 thinkpad 390x / i 1700 hmm.

  • Page 85: Upper Cover

    Upper cover “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “led board” on page 72 “upper heatsink” on page 73 “lcd panel” on page 77 to remove the upper case: 1. Remove the screws from the upper cover. 2 1 2. Turn the notebook over. Then remove the 4 s...

  • Page 86

    3. Use a flat-bladed screwdriver to remove the latch. 4. Disconnect the cable from the main unit. Now you can remove the upper cover from the base cover. 4 5 6 7 step size (quan- tity) head & color torque 3 m2.5 x 18l (3) pan head, black 2.0 kgf-cm note: make sure you use the correct screw for repla...

  • Page 87: Imm Lower Heatsink

    Imm lower heatsink “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “led board” on page 72 “upper heatsink” on page 73 “cpu board” on page 76 “lcd panel” on page 77 “upper cover” on page 79 to remove the imm lower heatsink: 1. Disconnect the fan cable fr...

  • Page 88: Fan

    Fan “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “led board” on page 72 “upper heatsink” on page 73 “cpu board” on page 76 “lcd panel” on page 77 “upper cover” on page 79 “imm lower heatsink” on page 81 remove the screw securing the fan. Lift the fan...

  • Page 89: Speakers

    Speakers note: this section is only for 15.0–inch lcd models. “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “led board” on page 72 “upper heatsink” on page 73 thinkpad 390x / i 1700 hmm 83.

  • Page 90

    Step size (quan- tity) head & color torque 1 m2.5 x 6l (4) flat head, black 2.0 kgf-cm note: make sure you use the correct screw for replacement. 84 thinkpad 390x / i 1700 hmm.

  • Page 91: Batt Board

    Power latch, ir board, and dc-dc & batt board “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “led board” on page 72 “upper heatsink” on page 73 “cpu board” on page 76 “lcd panel” on page 77 “upper cover” on page 79 “imm lower heatsink” on page 81 “fan”...

  • Page 92: System Board

    System board “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “led board” on page 72 “upper heatsink” on page 73 “cpu board” on page 76 “lcd panel” on page 77 “upper cover” on page 79 “imm lower heatsink” on page 81 “fan” on page 82 “speakers” on page 83...

  • Page 93

    Combo bay interposer board “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “led board” on page 72 “upper heatsink” on page 73 “cpu board” on page 76 “lcd panel” on page 77 “upper cover” on page 79 “imm lower heatsink” on page 81 “fan” on page 82 “power ...

  • Page 94: Lcd Bezel 15.0"

    Lcd bezel 15.0" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 step size (quan- tity) head & color torque 1 m2.5 x 6l (3) flat head, black 2.0 kgf-cm note: make sure you use the correct screw for replacement. 88 thinkpad 390x / i 1700 hmm.

  • Page 95: Lcd Inverter 15.0"

    Lcd inverter 15.0" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 15.0"” on page 88 note: see “setting the lcd panel id” on page 46. Step size (quan- tity) head & color torque 1 m2 x 4l (1) flat head, silver 1.6 kgf-cm note: make sure you us...

  • Page 96: Microphone 15.0"

    Microphone 15.0" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 15.0"” on page 88 “lcd inverter 15.0"” on page 89 90 thinkpad 390x / i 1700 hmm.

  • Page 97: Lcd Panel 15.0"

    Lcd panel 15.0" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 15.0"” on page 88 “lcd inverter 15.0"” on page 89 “microphone 15.0"” on page 90 1 step size (quan- tity) head & color torque m2.5 x 4l (4) flat head, black 2.0 kgf-cm note: make ...

  • Page 98

    5 4 step size (quan- tity) head & color torque m2 x 4l (6) flat head, silver 1.6 kgf-cm note: make sure you use the correct screw for replacement. 92 thinkpad 390x / i 1700 hmm.

  • Page 99: Lcd Bezel 14.1"

    Lcd bezel 14.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 remove the three screws securing the lcd bezel. Step size (quan- tity) head & color torque 2 m2.5 x 6l (3) pan head, black 2.0 kgf-cm note: make sure you use the correct screw for replaceme...

  • Page 100: Speaker 14.1"

    Speaker 14.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 14.1"” on page 93 to remove the speaker: 1. Carefully disconnect the speaker cable from the con- nector. 2. Remove the five screws securing the speaker. 3. Gently lift the speaker ...

  • Page 101: Vr Board 14.1"

    Vr board 14.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 14.1"” on page 93 “speaker 14.1"” on page 94 to remove the vr board: 1. Disconnect the power cable from the vr board. 2. Carefully remove the vr board from the display panel. Thin...

  • Page 102: Microphone 14.1"

    Microphone 14.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 14.1"” on page 93 “speaker 14.1"” on page 94 “vr board 14.1"” on page 95 to remove the microphone: 1. Disconnect the power cable from the microphone. 2. Lift the lcd away from t...

  • Page 103: Lcd Panel 14.1"

    Lcd panel 14.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 14.1"” on page 93 “speaker 14.1"” on page 94 “vr board 14.1"” on page 95 “microphone 14.1"” on page 96 remove the screw covers and screws. Step size (quan- tity) head & color tor...

  • Page 104: Lcd Inverter 14.1"

    Lcd inverter 14.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 14.1"” on page 93 “speaker 14.1"” on page 94 “vr board 14.1"” on page 95 “microphone 14.1"” on page 96 “lcd panel 14.1"” on page 97 note: see “setting the lcd panel id” on pag...

  • Page 105: Lcd Fpc 14.1"

    Lcd fpc 14.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 14.1"” on page 93 “speaker 14.1"” on page 94 “vr board 14.1"” on page 95 “microphone 14.1"” on page 96 “lcd panel 14.1"” on page 97 disconnect the lcd fpc cable from the lcd. Note:...

  • Page 106: Lcd Bezel 12.1"

    Lcd bezel 12.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 remove the three screws securing the lcd bezel. Step size (quan- tity) head & color torque 2 m2.5 x 6l (3) flat head, black 2.0 kgf-cm note: make sure you use the correct screw for replacem...

  • Page 107: Speaker 12.1"

    Speaker 12.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 12.1"” on page 100 to remove the speaker: 1. Carefully disconnect the speaker cable from the con- nector. 2. Remove the five screws securing the speaker. 3. Gently lift the speaker...

  • Page 108: Vr Board 12.1"

    Vr board 12.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 12.1"” on page 100 “speaker 12.1"” on page 101 to remove the vr board: 1. Disconnect the power cable from the vr board. 2. Carefully remove the vr board from the display panel. St...

  • Page 109: Lcd Inverter 12.1"

    Lcd inverter 12.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 12.1"” on page 100 “speaker 12.1"” on page 101 “vr board 12.1"” on page 102 note: see “setting the lcd panel id” on page 46. To remove the lcd inverter: 1. Disconnect the cabl...

  • Page 110: Microphone 12.1"

    Microphone 12.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 12.1"” on page 100 “speaker 12.1"” on page 101 “vr board 12.1"” on page 102 “lcd inverter 12.1"” on page 103 to remove the microphone: 1. Disconnect the power cable from the mic...

  • Page 111: Lcd Panel 12.1"

    Lcd panel 12.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 12.1"” on page 100 “speaker 12.1"” on page 101 “vr board 12.1"” on page 102 “lcd inverter 12.1"” on page 103 “microphone 12.1"” on page 104 step size (quan- tity) head & color to...

  • Page 112: Lcd Fpc 12.1"

    Lcd fpc 12.1" “battery” on page 61 “hard disk drive” on page 62 “combo bay” on page 63 “keyboard” on page 70 “lcd bezel 12.1"” on page 100 “speaker 12.1"” on page 101 “vr board 12.1"” on page 102 “lcd inverter 12.1"” on page 103 “microphone 12.1"” on page 104 “lcd panel 12.1"” on page 105 disconnect...

  • Page 113: System Unit Parts Listing

    System unit parts listing 1 2 3 4 5 7 10 11 12 13 14 15 16 17 18 19 20 21 22 25 26 24 27 23 29 30 31 28 19-1 20-1 9 8 5 6 thinkpad 390x / i 1700 hmm 107.

  • Page 114

    Index description fru number 1 middle cover 05k5481 2 led board w/ cable 10l1154 3 see keyboard list 4 upper heatsink for celeron and pentium ii 10l1930 5 cpu card (mmc-ii, celeron-400) 10l1439 cpu card (mmc-ii, pentium ii–400) 10l1440 cpu card (mmc-ii, pentium iii–450) 10l1354 cpu card (mmc-ii, pen...

  • Page 115

    Index description fru number battery (nimh) (panasonic) 02k6521 20-1 battery slider cover 05k5942 21 32mb dimm sdram (pc-100) 08k3408 64mb dimm sdram (pc-100) 08k3409 22 dimm door 05k5484 23 rtc 11j8591 24 pci modem card 10l1296 ethernet card 10l1437 25 modem door 08k5836 26 combo cd-rom + fdd 05k92...

  • Page 116

    Index description fru number kbd turkish 02k4721 kbd arabic 02k4722 kbd russian 02k4723 kbd slovakian 02k4724 kbd slovenian 02k4725 kbd hungarian 02k4726 kbd czech 02k4727 kbd japanese 02k4728 kbd traditional chinese 02k4729 kbd korean 02k4730 kbd la spanish 02k4731 miscellaneous misc name plate lab...

  • Page 117

    Index description fru number power cord (bahamas, barbados, bermuda, bolivia, canada, cayman islands, colombia, costa rica, dominican republic, ecuador, el salvador, guatemala, guyana, haiti, honduras,jamaica, korea (south), mexico, netherlands, antilles, nicaragua, panama, peru, philippines, saudi ...

  • Page 118: Lcd Unit Parts Listing

    Lcd unit parts listing 112 thinkpad 390x / i 1700 hmm.

  • Page 119: 12.1" Lcd Parts Listing

    12.1" lcd parts listing 1 2 3 4 5 6 7 8 9 10 11 index system unit fru number 1 lcd bezel (12.1" tft) 05k5469 2 microphone w/ holder 05k5477 3 cable for spk/mic/vr board 05k2818 4 speaker (12.1"/13.3") 05k5467 5 vr board (12.1"/13.3") 30l2576 6 lcd inverter (12.1" tft) 10l1645 7 lcd panel (12.1" tft)...

  • Page 120

    Index system unit fru number lg/ibm logo kit 05k6044 114 thinkpad 390x / i 1700 hmm.

  • Page 121: 14.1" Lcd Parts Listing

    14.1" lcd parts listing 1 2 3 4 5 6 7 8 9 10 12 11 index system unit fru number 1 lcd bezel (14.1" tft) 05k5945 2 microphone w/ holder 05k5477 3 cable for spk/mic/vr board 05k2818 4 speaker (14.1") 02k4869 5 lcd panel (14.1" tft) 05k9538 6 hinge l,r (14.1") 05k5947 7 hinge cap l,r (14.1") 05k5948 8 ...

  • Page 122

    Index system unit fru number lcd misc parts (lcd latch (l,r), spring, brightness/contrast knob for 12.1", brightness/contrast knob for 14.1", lcd bracket for 13.3" only) 05k5488 lg/ibm logo kit 05k6044 116 thinkpad 390x / i 1700 hmm.

  • Page 123: 15.0" Lcd Parts Listing

    15.0" lcd parts listing 1 2 3 6 4 5 9 8 7 index system unit fru number 1 lcd bezel (15.0" tft) 27l0491 2 lcd panel (15.0" tft) 08k5828 3 hinge bracket (l,r) 15.0" 08k5831 4 lcd fpc (15.0" tft) 27l0491 5 lcd inverter (15.0" tft) 10l1432 6 lcd rear cover (15.0" tft) 08k5829 7 microphone w/ holder 05k5...

  • Page 124: Service Tools

    Service tools note: the cpu tool is for depot use only. Description fru no. Qty. Tri-connector wrap plug 72x8546 pc test card 35g4703 audio wrap cable 66g5180 screwdriver kit 95f3598 usb parallel test cable 05k2580 cpu removal tool 08k5880 5.5mm socket 73g5354 5.0mm socket 73g1466 esd kit (wrist str...

  • Page 125: Notices

    Notices references in this publication to ibm products, programs, or services do not imply that ibm intends to make these available in all countries in which ibm operates. Any refer- ence to an ibm product, program, or service is not intended to state or imply that only ibm product, program, or serv...