J&a 3030 Operator's Manual - page 7

Manual is about: Heat press

Summary of 3030

  • Page 1

    O p e r a t o r s m a n u a l insignia house, vale road, spilsby, lincolnshire pe23 5he telephone +44 (0)1790 752757 www.Ja-int.Co.Uk j&a (international) limited.

  • Page 2

    C o n t e n t s 2 getting started 3 changing the settings 4 changing the plates & heat sealing best practices 5 heat sealing best practices & good ideas 6 heatseal parameters for transfers 7 heatseal parameters for badges 8 routine maintenance and calibration 9 servicing, repairs & troubleshooting 1...

  • Page 3

    Setting up 1 carefully remove the 3030 from the delivery box. Keep the box and packaging! You will need it for return-to-base servicing and repairs. 2 place the 3030 on a solid, level surface at a comfortable working height. 3 plug the 13 amp fused plug in to a 240v power supply. 4 switch on at rear...

  • Page 4

    3 changing the settings genera l the three important factors for a heatsealing process are time, temperature and pressure. The correct settings for each j&a product are given on pages 6 & 7. Each of the three settings may be changed on the 3030 as below. Generally, the left ( 3 ) and the right ( 4 )...

  • Page 5

    Bottom plate to remove existing bottom plate swing head of machine to the side to give clear working access to the bottom plate. Rotate the bottom plate anti-clockwise. This in effect simply unscrews it and after several turns can be lifted away. To install replacement plate insert post of bottom pl...

  • Page 6

    Opening out garments wherever possible, only heat seal onto one thickness of fabric this, for example, entails opening out garments and putting only either the front or back, as appropriate, over the base plate. Fabric finishes modern fabrics can be coated or finished with a variety of different che...

  • Page 7

    6 heat seal parameters - transfers hot cold cold cold cold cold hot hot warm cold cold cold warm cold cold medium high medium high high low medium / low high medium / low medium / low medium medium / low medium / low medium / low medium / low 35 15 - 20 10 15 - 20 10 12 - 18 10 -12 7 - 10 10 10 10 1...

  • Page 8

    7 heat seal parameters - badges n / a n / a n / a cold n / a n / a high high low high medium / low firm 15 - 18 12 - 15 12 - 18 15 - 20 10 - 12 20 210ºc / 410ºf 210ºc / 410ºf 140 - 180ºc 284 - 356ºf 210ºc / 410ºf 160 - 180ºc 320 - 356ºf 210ºc / 410ºf interplaten temp dwell time (secs) interplaten pr...

  • Page 9

    3030 not working? - see the trouble shooting guide on page 9 occasionally clean top and bottom heat plates with a solvent such as j&a superspray and a clean, dry cloth. Regularly check that the temperature between the heat plates is the same as is reading on the display. To measure the inter-plate t...

  • Page 10

    Where a machine is owned (rather than rented on the j&a seal-deal scheme) the j&a annual service is recommended. This full return-to-base, strip-down and return system gives your machine a complete overhaul with change of key components for a minimal fixed outlay each year. Probably the most attract...

  • Page 11

    Micro switch solid state relay heater mains,filter,fuse connector and switch unit + – e l n chassis carry sleeves and screens to ends 10 wiring diagram.

  • Page 12

    1 sleeve, rubber 2 circlip 3 handle 4 lever 5 pin, roller bearing 6 roller bearing 7 bush 8 cover type a 9 sleeve, rubber 10 nylon washer 11 badge 11 arm assembly 12 arm 13 guide 14 screw, counter sink/sunk 15 arm stop 16 counter sink/sunk 17 spring rh 18 spring lh 19 pin, lever pivot 20 pin, roll 2...

  • Page 13

    1 base 2 bush 3 cover, base 4 screw 5 pad, rubber 6 nut, domed 7 adjuster 8 collar 9 spring bolt 10 nut, half 11 screw, cap 12 base assembly 12 retainer, arm 13 screw 14 nut locking 15 screw adjusting 16 relay 17 switch/plug 18 buzzer 19 control panel 20 decal, control panel 21 decal, pressure 22 de...

  • Page 14

    13 1 bearings, shoulder 2 mount, heated platen 3 screw, round 4 washer, plain 5 shield, heat 6 spacer 7 cover, element 8 element order numbers 6x6 127011 10x10 127012 12x8 127013 9 retainer, element 10 teflon order numbers 6x6 127004 10x10 127005 12x8 127006 platens (standard) 11 decal, ‘hot’ large ...

  • Page 15

    250mm x 250mm 10” x 10” 300mm x 200mm 12” x 8” 14 optional platens 1. Cover, type b 2. Top platen 250mm x 250mm 3. Base platen 250mm x 250mm 4. Top platen 300mm x 200mm 5. Base platen order numbers - for base plattens 6x6 127001 10x10 127002 12x8 127003.