J&B Importers Miami Sun Assembly Manual - page 3

Summary of Miami Sun

  • Page 1

    Trike assembly manual revised 3-98.

  • Page 2: Miami Sun Limited Warranty

    Miami sun limited warranty the miami sun frame, purchased from an authorized dealer is warranted to be free from defects in materials provided the trike is owned by the original buyer. The original fork and rear unit is warranted to be free from defects for a period of 90 days from date of purchase....

  • Page 3

    Please read this manual before riding your adult trike this manual is intended for you to read carefully so that you may enjoy your adult three wheeler and be an informed rider aware of the benefits as well as the warn- ings and safety issues in riding this tricycle. A trike is not a bicycle and thi...

  • Page 4: Checklist Before Riding

    4 checklist before riding 1. Check your tires for proper air pressure. If you need to inflate them do not inflate over the recommended air pressure on the side wall. 2. Test your front brake and make sure it stops the trike. If you have any doubts do not ride and see your dealer. All trikes are equi...

  • Page 5: Miami Sun

    Miami sun parts list and description 1. Frame 2. Fork 3. Headset 4. Front cantilever brake w/ locking lever 5. Front fender with braces 6. Front wheel, tire, tube 24 x 1.75 7. Stem 8. Handlebar 9. Grips 10. Western saddle with clips 11. Seat brace 12. Seat post 13. Trike basket with fittings 14. Bot...

  • Page 6: "miami Sun"

    6 trike parts list & description (13) 6702180 basket trike white vinyl coated 6702181 basket fittings (16) 6702067 crank one piece 6" (14) 22240 b.B. Opc set 24 tpi (16) 6702068 chainring 1/2x1/8"x36t (15) 6702295 chainguard cp hockey stick style opc 6702172 chainguard cp full round style opc (18) 1...

  • Page 7: "miami Sun"

    7 "miami sun" trike assembly instructions* step 1) steering head adjustment a. Place trike in an upright position on floor, loosen head lock nut and the adjusting cone. B. Re-tighten adjusting cone finger-tight. Turn the fork from side to side. Fork should turn with no rocking or free play. C. Secur...

  • Page 8: Step 2)   Contõd

    Step 2) contÕd c. Make sure that safety fork washer devices remain hooked into fork end tips. D. “ warning: do not ride without safety fork washers.Ó (fig. 3) 8 arms flange support bar left side top view right side step 3) free wheel rear unit assembly a. Thread the free wheel adapter into the plain...

  • Page 9: Adjustment of F.W. Unit

    Step 4) attaching free wheel rear unit to frame installing unit to frame is a simple matter of attaching two pairs of long and short carriage bolts. Please proceed in the following sequence: a. Install loosely the two large carriage bolts with their nuts and washers, to the two holes in the end of t...

  • Page 10: Step 6)   Attaching Pedal

    R step 6) attaching pedal s a. Each pedal axle is marked with "r" (right) or "l" (left). Install them in their correct position. Note that the left pedal tightens by turning counter clockwise and that the right tightens clockwise.The right side is the chain wheel side. 10 (fig. 7) step 7) axle key i...

  • Page 11: Step 8)   Contõd

    Step 8) contÕd b. Now put the second wheel on left side . This wheel is the idler. First slip on the spacer, then the wheel, followed by a washer and the locking nut until it touches the bearing. Again do not over tighten. Leave some play. C. Very important : it is critical for the protection of the...

  • Page 12: Step 10)   Attaching

    (fig.12) step 10) attaching vinyl basket a. With the reflector bracket on basket facing rear, place and center the basket onto the unit basket support bars. B. Align the two holes of unit basket support bar with the holes of the basket attaching brace. Attach nuts and bolts and finger tighten. Repea...

  • Page 13

    (it is advisable that all nuts & bolts be checked for tightness & security) step 13) attaching reflector kit the white reflector is bolted to reflector bracket on fork. The red reflector is bolted to reflector bracket on rear of basket. The wheel reflectors are installed opposite valve stems on rims...

  • Page 14: Helpful Hint:

    Trike coaster brake & 3-speed coaster brake conversion instruction (optional) helpful hint: the trike cb & 3-spd. C.B. Hub units are adjusted & aligned the same way as you would a cb wheel on an ordinary bike. Note: when installing a coaster brake or 3-spd. Coaster brake, you must substitute the fix...

  • Page 15: Step 3-A)

    Step 3-a) place cb or 3-spd. C.B. Hub unit into special frame conversion slot brackets located on top of rear bottom frame stays, attach nuts. ( fig.14) step 7-a) attach fixed sprocket onto rear trike axle. See fig. 4b (pg. 9) and step 8 (pg. 11) you are now ready to attach unit to trike. Step 4-a) ...

  • Page 16

    Step 9-a) chain installation & adjustment 1. Thread small 50 link chain over cb or 3-spd. C.B. Welded sprocket and unit fixed sprocket. Connect the connecting link, align both sprockets, install axle key and tighten set screw. 2. Slowly pull unit towards end of trike until chain slack is taken up. 3...