Japan CBM Corporation CMP-10 Service Manual

Summary of CMP-10

  • Page 1

    Cmp-10 service manual cmp-10 rev. 1.00 p 1/41 date: 2002.07.25 cmp-10 service manual product name: cmp-10 territory: td revision: 1.0 date: 2002.07.25 designed: approved: approvals: r&d department : qc department : manufacturing department : marketing department :.

  • Page 2

    Cmp-10 service manual cmp-10 rev. 1.00 p 2/41 date: 2002.07.25 revision rev. No. Date comment rev. 1.0 july 24, 2002 newly issued.

  • Page 3

    Cmp-10 service manual cmp-10 rev. 1.00 p 3/41 date: 2002.07.25 introduction this manual describes the disassembly, reassembly, and maintenance procedures of citizen mobile printer cmp-10. It is intended for field maintenance men. 1. Features this small, portable line thermal printer is designed for ...

  • Page 4

    Cmp-10 service manual cmp-10 rev. 1.00 p 4/41 date: 2002.07.25 2. General specifications feature parameters 1. Printing system direct thermal printing 2. Printing speed 50 mm/sec 3. Printing head total dots: 384 dot density: 8 dots/mm printing width: 48 mm 4. Emulation esc/pos commands + unique comm...

  • Page 5

    Cmp-10 service manual cmp-10 rev. 1.00 p 5/41 date: 2002.07.25 feature parameters 21. Operation switches power switch 1, lf switch 1 22. Sensors and error monitoring paper end sensor, open cover sensor, head temperature, low battery 23. Power consumption idle - approximately 2w when printing - appro...

  • Page 6

    Cmp-10 service manual cmp-10 rev. 1.00 p 6/41 date: 2002.07.25 3. Disassembly and reassembly in case of maintenance work, observe the following: caution (1) if the printer functions properly, do not disassemble, reassemble, or adjust it. Particularly, do not loosen each set screw unless required. (2...

  • Page 7

    Cmp-10 service manual cmp-10 rev. 1.00 p 7/41 date: 2002.07.25 screw (4) unscrew the screw on the bottom of the paper magazine. (5) close the paper cover. (3) remove the paper roll from the paper magazine..

  • Page 8

    Cmp-10 service manual cmp-10 rev. 1.00 p 8/41 date: 2002.07.25 2. Removing the battery cover (1) press the marked area on the battery cover and lift the cover. 3. Removing the battery (1) open the battery cover as shown above. (2) take out the battery pack. (3) disconnect the battery pack from the c...

  • Page 9

    Cmp-10 service manual cmp-10 rev. 1.00 p 9/41 date: 2002.07.25 (5) remove two m3 × 10 (bt) screws. 4. Removing the back cover (1) turn the printer downward. (2) push the front cover at the places shown on the drawing and lift the back cover. (3) remove the back cover..

  • Page 10

    Cmp-10 service manual cmp-10 rev. 1.00 p 10/41 date: 2002.07.25 5. Removing the paper cover (1) lift the printer. (2) take out the paper cover as shown on the drawing. 6. Removing the main pcb and operational panel (1) unscrew the three screws with which the main pcb is fixed to the plastic case as ...

  • Page 11

    Cmp-10 service manual cmp-10 rev. 1.00 p 11/41 date: 2002.07.25 (2) lift up the main pcb together with the operational panel. (3) disconnect the printer cables and buzzer cable. (4) remove the main pcb and the operational panel. (5) disconnect the operational panel from the main pcb. 7. Removing the...

  • Page 12

    Cmp-10 service manual cmp-10 rev. 1.00 p 12/41 date: 2002.07.25 8. Removing the platen (for model cmp-10-40) (1) unscrew the screws as shown on the drawing. (2) detach the platen..

  • Page 13

    Cmp-10 service manual cmp-10 rev. 1.00 p 13/41 date: 2002.07.25 9. Removing the operational panel pcb (1) unscrew the two screws and detach the operational panel pcb from the plastic panel. 3.2 reassembly procedure reassemble the disassembled parts in the reverse order of the disassembly procedure d...

  • Page 14

    Cmp-10 service manual cmp-10 rev. 1.00 p 14/41 date: 2002.07.25 4. Troubleshooting 4.1 troubleshooting procedure if the printer has a trouble, confirm its phenomenon, determine a defective part according to 4.2 troubleshooting guide, and then, repair it in the specified manner. • phenomenon find a c...

  • Page 15

    Cmp-10 service manual cmp-10 rev. 1.00 p 15/41 date: 2002.07.25 phenomenon the fuse blows out immediately if replaced. It blows out during operation. (f2 blows out) cause the ac adapter is not connected. Battery pack is not connected. Battery pack is discharged. The fuse is gone. Others the printer ...

  • Page 16

    Cmp-10 service manual cmp-10 rev. 1.00 p 16/41 date: 2002.07.25 phenomenon no printing thin printing color missing dots missing dots in specific section cause faulty battery pack battery pack is discharged. Faulty mounting and connection of printer mechanism the printer operates properly except not ...

  • Page 17

    Cmp-10 service manual cmp-10 rev. 1.00 p 17/41 date: 2002.07.25 phenomenon low print quality too much ink blot blurred characters cause faulty printing paper faulty battery pack foreign substance adhered to the thermal head or platen roller faulty printing paper worn platen roller check method check...

  • Page 18

    Cmp-10 service manual cmp-10 rev. 1.00 p 18/41 date: 2002.07.25 phenomenon pe is always detected. Pe is not detected. Cause faulty sensor faulty sensor foreign substance caught by the sensor sensor exposed to the direct sunshine or strong light check method use a tester to check whether or not a sup...

  • Page 19

    Cmp-10 service manual cmp-10 rev. 1.00 p 19/41 date: 2002.07.25 5. Assembly drawing.

  • Page 20

    Cmp-10 service manual cmp-10 rev. 1.00 p 20/41 date: 2002.07.25 pos name quantity 1 cover front 1 2 button 1 3 printer base 1 4 paper cover 40 mm 1 5 cover back 1 6 lamella 1 7 rubber foot 2 8 belt clip 1 9 screw m3 × 6 2 10 strap hook 2 11 rs connector cover 1 12 main pcb 1 13 screw m2.5 × 8 4 14 o...

  • Page 21

    Cmp-10 service manual cmp-10 rev. 1.00 p 21/41 date: 2002.07.25 6. Electrical diagram of main pcb.

  • Page 22

    Cmp-10 service manual cmp-10 rev. 1.00 p 22/41 date: 2002.07.25 6.1 cmp-10 main pcb - top side.

  • Page 23

    Cmp-10 service manual cmp-10 rev. 1.00 p 23/41 date: 2002.07.25 6.2 cmp-10 main pcb - bottom side.

  • Page 24

    Cmp-10 service manual cmp-10 rev. 1.00 p 24/41 date: 2002.07.25 6.3 cmp-10 main pcb - top side.

  • Page 25

    Cmp-10 service manual cmp-10 rev. 1.00 p 25/41 date: 2002.07.25 6.4 cmp-10 main pcb - bottom side.

  • Page 26

    Cmp-10 service manual cmp-10 rev. 1.00 p 26/41 date: 2002.07.25 7. Main pcb - parts list no. Name part number manufacturer u1 interface ic sp232ect sipex u2 battery charging ic mm1433bv mitsumi u3 a/d converter tlc0832 ti u4 cmos ic cd4066 fairchild u5 cmos ic cd4066 fairchild u6 1 mbit sram k6t1008...

  • Page 27

    Cmp-10 service manual cmp-10 rev. 1.00 p 27/41 date: 2002.07.25 no. Name part number manufacturer d1 fast recovery diode sr240 daesan d2 fast recovery diode sr240 daesan d3 fast recovery diode sr240 daesan d4 diode ll4148 daesan d5 fast recovery diode sr240 daesan d6 diode ll4148 daesan d7 diode ll4...

  • Page 28

    Cmp-10 service manual cmp-10 rev. 1.00 p 28/41 date: 2002.07.25 no. Name part number manufacturer c29 chip capacitor 100 nf/50 v walsin c30 chip capacitor 100 nf/50 v walsin c31 chip capacitor 100 nf/50 v walsin r1 chip resistor 0805 5% 10 k yageo r2 chip resistor 0805/5% 130 k yageo r3 chip resisto...

  • Page 29

    Cmp-10 service manual cmp-10 rev. 1.00 p 29/41 date: 2002.07.25 no. Name part number manufacturer v9 multilayer varistor walsin f1 fuse f-1206(1a) (1 a) bel fuse f2 fuse f-1206(3.5a/20v~) (2.5 a/20 v~) bel fuse l1 ferite bead 2012 0,1uh 25 mhz/~50 ohm, samwha 100 mhz/~75 ohm cn1 3 pin connector mole...

  • Page 30

    Cmp-10 service manual cmp-10 rev. 1.00 p 30/41 date: 2002.07.25 8. Panel pcb - top view.

  • Page 31

    Cmp-10 service manual cmp-10 rev. 1.00 p 31/41 date: 2002.07.25 8.1 panel pcb ass’y - bottom view.

  • Page 32

    Cmp-10 service manual cmp-10 rev. 1.00 p 32/41 date: 2002.07.25 8.2 panel pcb ass’y - top view.

  • Page 33

    Cmp-10 service manual cmp-10 rev. 1.00 p 33/41 date: 2002.07.25 8.3 panel pcb ass’y - bottom view.

  • Page 34

    Cmp-10 service manual cmp-10 rev. 1.00 p 34/41 date: 2002.07.25 no. Name part number manufacturer u1 infrared tranceiver tfdu4100 vishay u2 f2f2000 f2f2000 zepetronic u3 analog switch ic cd4066 fairchild q1 npn transistor 2sa1162-gr toshiba kta1504 kec q2 npn transistor 2sa1162-gr toshiba kta1504 ke...

  • Page 35

    Cmp-10 service manual cmp-10 rev. 1.00 p 35/41 date: 2002.07.25 no. Name part number manufacturer c10 chip capacitor 0805 10 nf/20% walsin c11 chip capacitor 0805 10 nf/20% walsin cn1 magnetic head n2 12 pin molex molex 87049-1016 molex cn3 6 pin molex molex 87049-0616 molex cn4 magnetic head sw1 ta...

  • Page 36

    Cmp-10 service manual cmp-10 rev. 1.00 p 36/41 date: 2002.07.25 battery specification 1. Scope this product specification (‘specification’ hereinafter) covers the requirements for the rechargeable lithium- ion battery pack manufactured and supplied by samsung sdi co., ltd. To japan cbm corporation f...

  • Page 37

    Cmp-10 service manual cmp-10 rev. 1.00 p 37/41 date: 2002.07.25 4. Outline dimension refer to attached drawing. 5. Appearance any critical cosmetic damage must not be found from the appearance of the products. 6. Standard test condition 6.1 test sample condition the battery pack used for the test sh...

  • Page 38

    Cmp-10 service manual cmp-10 rev. 1.00 p 38/41 date: 2002.07.25 7.4 initial internal impedance this means ac impedance of the battery pack measured at 1 khz after standard charge. Initial internal impedance 7.5 discharge capacity with temperature this means relative value of discharge capacity at va...

  • Page 39

    Cmp-10 service manual cmp-10 rev. 1.00 p 39/41 date: 2002.07.25 9. Safety test 9.1 overcharge test test method: apply charge voltage 12 v with current 1.0 c to the battery pack. Criteria: pcm shall operate and stop charging. Capacity > 87% no damage such as leakage, flame, fire was allowed. 9.2 exte...

  • Page 40

    Cmp-10 service manual cmp-10 rev. 1.00 p 40/41 date: 2002.07.25 11. Shipment the battery pack shall be shipped in a 40~60% charged state. 12. Caution and prohibition before using and handling the battery pack, see carefully attached “handling instruction for lithium ion rechargeable battery pack”. 1...

  • Page 41

    Cmp-10 service manual cmp-10 rev. 1.00 p 41/41 date: 2002.07.25 handling instruction for lithium ion rechargeable battery pack safety instructions please follow the warnings and precautions listed below to avoid possible hazards from the improper use of batteries and to ensure correct and safe use o...