1. DL manuals
  2. Jaybeam Wireless
  3. Antenna
  4. 5121100
  5. Installation Manual

Jaybeam Wireless 5121100 Installation Manual

Manual is about: 3G

Summary of 5121100

  • Page 1

    Issue 05 page 1/20 installation guide for 3g antennas installation guide for 3g antennas _________ table of content section 1 - presentation....................................................................................................... 2 mounting accessory list..................................

  • Page 2

    Issue 05 page 2/20 installation guide for 3g antennas section 1 - presentation this guide describes the various installation accessories available for our 3g antennas. Each of them is delivered with an installation drawing. Depending on antenna type, the attachment of the installation accessories is...

  • Page 3

    Issue 05 page 3/20 installation guide for 3g antennas accessory part number antenna type pole brackets 48-115 mm (note 0) pole brackets 70-150 mm wall brackets with azimuth pan mechanical tilt (note 1) tilt label mark (note 2) 5165100 5157120 5232100 0900181/00 0900182/00 0900183/00 0900188/00 g 516...

  • Page 4

    Issue 05 page 4/20 installation guide for 3g antennas section 2 - accessories for antennas with pivot points at the back 2.1 - hardware for pole mounting (standard) this accessory is used for installation on pipes of 48 to 115 mm diameter. The figures and part list below describe the kit and how to ...

  • Page 5

    Issue 05 page 5/20 installation guide for 3g antennas 2 pivots points antenna - pole mounting 48 to 115 mm - 0900181/00 part list item description quantity item description quantity 1 pole clamp 4 6 m8 full nut 12 2 antenna bracket 2 7 m8 x 130 mm hex head bolt 2 3 spacing tube 2 8 m10 x 200 mm hex ...

  • Page 6

    Issue 05 page 6/20 installation guide for 3g antennas 2.2 - hardware for pole mounting (large) this accessory is used for installation on pipes of 70 to 150 mm diameter. The figures and part list below describe the kit and how to assemble it on the antenna. The middle components do not apply to ante...

  • Page 7

    Issue 05 page 7/20 installation guide for 3g antennas 2 pivots points antenna - pole mounting 115 to 150 mm - 0900182/00 part list item description quantity item description quantity 1 pole clamp 4 6 m8 full nut 12 2 antenna bracket 2 7 m8 x 130 mm hex head bolt 2 3 spacing tube 2 8 m10 studding 260...

  • Page 8

    Issue 05 page 8/20 installation guide for 3g antennas 2.3 - hardware for wall mounting this accessory is used for installation on wall with ±30° azimuth panning capability. The figures and part list below describe the kit and how to assemble it on the antenna. The middle components do not apply to a...

  • Page 9

    Issue 05 page 9/20 installation guide for 3g antennas the panning device has the following capabilities: -30° pan 0° pan +30° pan the accessory parts list is given below. 2 pivots points antenna - wall mounting with pan - 0900183/00 part list item description quantity item description quantity 1 wal...

  • Page 10

    Issue 05 page 10/20 installation guide for 3g antennas 2.4 - hardware for mechanical tilt this accessory is used to add mechanical tilt capability to the mounting accessories described above for installation. The part number for the mechanical tilt hardware depends on the antenna type because each t...

  • Page 11

    Issue 05 page 11/20 installation guide for 3g antennas 2 pivots points antenna - mechanical tilt kit - 0900184/00 or 0900188/00 part list item description quantity item description quantity 1 long scissor arm 1 5 m8 x 130 mm hex head bolt 2 2 short scissor arm 1 6 m8 plain washer 3 3 spacing tube 1 ...

  • Page 12

    Issue 05 page 12/20 installation guide for 3g antennas 2.5.2 - antennas with three mounting pivot points the accessory p/n 0900533/00 is dedicated only to antenna with 3 pivots at the back. It is used for installation on wall with ±30° azimuth panning and mechanical tilt capability. It includes the ...

  • Page 13

    Issue 05 page 13/20 installation guide for 3g antennas section 3 - accessories for antennas with mounting plates at top and bottom 3.1 - hardware for pole mounting (standard) the accessory p/n 0900390/00 is a set of two pole brackets for installation on pipes of 48 to 115 mm diameter. The figures an...

  • Page 14

    Issue 05 page 14/20 installation guide for 3g antennas 3.2 - hardware for pole mounting (large) the accessory p/n 0900503/00 is a set of two pole brackets for installation on pipes of 70 to 150 mm diameter. The figures and part list below describe the kit and how to assemble it on the antenna. 09005...

  • Page 15

    Issue 05 page 15/20 installation guide for 3g antennas 3.3 - hardware for wall mounting the accessory p/n 0900408/00 is a set of two brackets for installation on wall with ±30° azimuth panning capability. The figures and part list below describe the kit and how to assemble it on the antenna. 0900408...

  • Page 16

    Issue 05 page 16/20 installation guide for 3g antennas the panning device has the following capabilities: -30° pan 0° pan +30° pan.

  • Page 17

    Issue 05 page 17/20 installation guide for 3g antennas 3.4 - hardware for mechanical tilt on pole mounting the accessory p/n 0900374/00 is a kit that adds mechanical tilt capability to the pole mounting or wall mounting accessories described above. It cannot be used on its own. The figures and part ...

  • Page 18

    Issue 05 page 18/20 installation guide for 3g antennas 3.5 - hardware for mechanical tilt on wall mounting for such installation both the panning accessory (see section 3.3) and the mechanical tilt accessory (see section 3.4) need to be used in combination..

  • Page 19

    Issue 05 page 19/20 installation guide for 3g antennas section 4 - installation 4.1. - general guidelines each antenna is delivered fully assembled in a single packing carton. Do not stack more than three units high. The antenna has breather/drain holes at its bottom and should be installed with the...

  • Page 20

    Issue 05 page 20/20 installation guide for 3g antennas connection: important: the antenna positioning should be completed before connecting cables. Fit the jumper cables to the antenna connectors. The "+" and the "-" coaxial ports are interchangeable unless otherwise specified by the operator's requ...