1. DL manuals
  2. K&W Model Airplanes
  3. Toy
  4. Bristol F2-B 1917 Fighter
  5. Assembly Manual

K&W Model Airplanes Bristol F2-B 1917 Fighter Assembly Manual

Summary of Bristol F2-B 1917 Fighter

  • Page 1

    Bristol f2b fighter arf 1 assembly manual for arf stand-off scale model in 1:5 scale. Historical data and presentation. Model design and construction drawing by göran kalderén © revised 2000-09-05 bristol f2-b 1917 fighter.

  • Page 2

    Bristol f2b fighter arf 2 the aircraft was armed with a single syn- chronized .303 vickers machine gun with 963 rounds of ammunition in the nose for the pilot and a .303 lewis machine gun for the observer with seven 97 round ammunition drums. Some aircraft were upgunned in the field with an addi- ti...

  • Page 3: Bristol F2B

    Bristol f2b fighter arf 3 bristol f2b fighter 1917 specification: wingspan, 39' 3" (11,96 m.) length, 25' 10" (7,87 m.) heigth, 9' 9" (2,97 m.) engine, 275 hp rolls royce falcon iii liquid cooled. Armament, 1 vickers .303 forward firing syncronized machine gun, 1 lewis on scarf ring mount in rear co...

  • Page 4

    Bristol f2b fighter arf 4.

  • Page 5

    Bristol f2b fighter arf 5 bristol f2b fighter and canadian pilots the canadian air force only ever held two ”brisfits” or ”bifs” on strength from 6 august, 1920 to 7 feb- ruary, 1922 as part of an imperial gift of 114 varied aircraft, however canadian airmen flew the two-seat fighters in the service...

  • Page 6

    Bristol f2b fighter arf 6 our model depicts the bristol f2b d8084, no.139 sqn raf villaverla aerodrome in september 1918. Originally formed in march 1918 as ’z’ flight and attached to no.34 sqn in italy for long range recon- naissance duties. By july 1918 a second flight had arrived and the combined...

  • Page 7

    Bristol f2b fighter arf 7 the bristol f2b fighter, that we have modeled, is the aircraft that is kept in flying condition by the shuttleworth collection in england. These pictures show details of the aircraft as it looks today. The front cowling plates have been removed for service and reveal the po...

  • Page 8

    Bristol f2b fighter arf 8 the impressive rolls royce falcon iii 275 hp 12 cylinder liquid cooled v-engine. The picture below shows also the spent cartridge chute and the rear part of the vickers machine gun..

  • Page 9

    Bristol f2b fighter arf 9 the model we have chosen the scale of 1:5 that gives a model with the wingspan of almost 8 feet. This in turn is a rather large aircraft but the han- dling in the air is very satisfactory. For transport to and from the flying field, both wing panel groups can be removed, ri...

  • Page 10

    Bristol f2b fighter arf 10 30 mm. 1.5 mm. Complete "turnbuckle" assembly typical fashion of lacing bungee rubber cord. The upper center section (4 allen 6-32 screws. Either one of the 2 aluminum panels can now be removed by unscrewing the sheet metal screws. Note that different length of screws have...

  • Page 11

    Bristol f2b fighter arf 11 the mq version with full detailing our prototype in flight cockpit details with optional instrument panel installed.

  • Page 12

    Bristol f2b fighter arf 12 1 11 2 10 2 13 12 8 4 3 3 10 2 9 7 12 5 11 2 2 14 3 4 4 5 6 6 6 10 11 2 2 1 13 13 14 these are the rigging wires: 1. Rudder control wires 2. Elevator control wires 3. Front flying wires 4. Rear flying wires. 5. Front landing wires 6. Rear landing wires. 7. Landing gear cro...

  • Page 13

    Bristol f2b fighter arf 13 stabilizer fits in here fixed screw supports adjustment screw fixed screw supports adjustable leading edge support balancing check the c/g and make adjustments if necessary. C/g should be within the range of 9 cm - 12 cm (3.6" - 4.8") measured from the leading edge on the ...

  • Page 14

    Bristol f2b fighter arf 14 cockpit interior including instrument panel is an additional option. For adjustment of the stabilizer incidence it is recommended to set the stabilizer approx 3mm from the upper end position. Adjust after intitial flight to suite your taste. The servo y-leads from the rece...

  • Page 15

    Bristol f2b fighter arf 15 the engine installation is related to the type of engine that you have chosen. We like to show how we installed the os 1.20 engine and including a "scale" type functional manifold. To ensure an unrestricted air inflow we removed three panels of the screen above the propell...

  • Page 16

    Bristol f2b fighter arf 16 what is in the box: the arf and rnf kits contains the parts shown in the picture all the parts are covered and painted. All the rigging 1. Fuselage with upper and lower wing cabanes 2. Landing gear with wheel shaft 3. Scale wheels 4. Scale propeller 5. Tail skid assy., mou...