La Spaziale S40 Classic Installation Instructions Manual

Manual is about: Espresso Coffee Machine

Summary of S40 Classic

  • Page 1

    Lsi 024 - rev. 01 - ed. 10/2016 tanti stili...Una passione several styles...One passion espresso coffee machines.

  • Page 2

    Espresso coffee machines ii 40 lsi 024 - rev. 01 - ed. 10/2016 weee disposal of the equipment by the users within the european community (weee) in compliance with the article 13 of the legislative decree is- sued on 25 july 2005, nr 151 ”implementation of the directives 2002/95/ce, 2002/96/ce e 2003...

  • Page 3

    Espresso coffee machines 1 40 lsi 024 - rev. 01 - ed. 10/2016 index 1. General description of the machine ................................. 2 1.1 control panel description ............................................... 3 1.2 coffee dispensing touchpad............................................. 4 ...

  • Page 4

    Espresso coffee machines 2 40 lsi 024 - rev. 01 - ed. 10/2016 1. General description of the machine legend 1. Programming button 2. Control panel 3. Coffee dispensing button + 4 digit display 4. Steam dispensing tap 5. Steam wand with incorporated tempera- ture sensor (m.A.T.) (optional) 6. Boiler p...

  • Page 5

    Espresso coffee machines 3 40 lsi 024 - rev. 01 - ed. 10/2016 1.1 control panel description fig. 2 legend 1. Programming keyboard p = programming keyboard + = value increase button - = value decrease button = cup heater button 2. Control panel warning light = temperature alarm warning light boiler t...

  • Page 6

    Espresso coffee machines 4 40 lsi 024 - rev. 01 - ed. 10/2016 1.2 coffee dispensing touchpad legend 1. Display 2. 2 long coffees key 3. 2 short coffees key 4. Continuous delivery key 5. 1 long coffee key 6. 1 short coffee key fig. 3 4 4 1 1 6 5 2 3 classic suprema.

  • Page 7

    Espresso coffee machines 5 40 lsi 024 - rev. 01 - ed. 10/2016 2. General warnings read carefully the instructions and warnings contained in this manual and in the “ instruction manual for the installer ”, since they provide important indications concerning the installation of the appliance. Danger! ...

  • Page 8

    Espresso coffee machines 6 40 lsi 024 - rev. 01 - ed. 10/2016 danger! If it becomes necessary to replace the machine’s power supply cable, utilise only these types: cet electric h07rn-f 5 x 2.5mm (400v) for 2/3 group versions, 5 x 4mm (400v) for 4 group versions - cet electric single phase 3 x 2.5mm...

  • Page 9

    Espresso coffee machines 7 40 lsi 024 - rev. 01 - ed. 10/2016 attention! The appliance must be installed on a flat bearing surface, the stability of which needs to be checked. Attention! The appliance must be installed where use and maintenance are restricted to trained staff. The electrical power s...

  • Page 10

    Espresso coffee machines 8 40 lsi 024 - rev. 01 - ed. 10/2016 3. Removing the packaging after unpacking the machine, please check its integrity; in case of doubt, do not use it and consult the manufacturer. Packaging materials must not be left within children’s reach since they are potentially dange...

  • Page 11

    Espresso coffee machines 9 40 lsi 024 - rev. 01 - ed. 10/2016 3.2 optional accessories (supplied only on request of the customer) legend i. Water softener l. Water line impurity filter m. Pressure reducer n. Detergent.

  • Page 12

    Espresso coffee machines 10 40 lsi 024 - rev. 01 - ed. 10/2016 4. Installation place the machine on the support surface, lifting it up only from underneath. Adjust the feet so that the machine fits perfectly in a horizontal position and tilting slightly backwards. Before connecting the machine to th...

  • Page 13

    Espresso coffee machines 11 40 lsi 024 - rev. 01 - ed. 10/2016 danger! The light blue conductor lead of cable ( a ) is connected to the neutral phase of the electrical system. Take note! 230 v single-phase connections are only possible with rating plate data refer a power less than 6300 w..

  • Page 14

    Espresso coffee machines 12 40 lsi 024 - rev. 01 - ed. 10/2016 4.2 water mains installation diagram attention! The machine is supplied without water in the boiler to avoid exposure to temperatures less than 0°c that could cause irrepa- rable damage. Legend: 1 water tap (previously installed by the c...

  • Page 15

    Espresso coffee machines 13 40 lsi 024 - rev. 01 - ed. 10/2016 danger! Installation of the water softener is recommended to prolong the life of the machine. Before installing the machine, check the hardness of the water and fit a softener based on the instructions of the manufacturer and to standard...

  • Page 16

    Espresso coffee machines 40 14 lsi 024 - rev. 01 - ed. 10/2016 5. Electrical switch on of the appliance 1. Move the appliance switch under the bottom panel, to “ i ”. Fig. 6 filling with water: after 3 seconds from switching on for the first time, the appliance will automatically fill the boiler wit...

  • Page 17

    Espresso coffee machines 15 40 lsi 024 - rev. 01 - ed. 10/2016 for coffee preparation instructions, or for pouring hot water or dispensing steam for hot beverages, see the use and maintenance manual. 6. Programming the programming menu can be used to programme the boiler temperature, coffee doses, h...

  • Page 18

    Espresso coffee machines 16 40 lsi 024 - rev. 01 - ed. 10/2016 6.3 programming hot water press the “hot water delivery” key to commence delivery of the water. The main dis- play will show the pouring time. Once the required amount of water is in the jug, press the same key to stop the ongo- ing deli...

  • Page 19

    Espresso coffee machines 17 40 lsi 024 - rev. 01 - ed. 10/2016 6.5 programming access block to quit programming, press and hold down the “cup warmer” for 5 seconds; in this mode it is possible to enable the programming access block function. With this function enabled, enter the programming mode wit...

  • Page 20

    Espresso coffee machines 18 40 lsi 024 - rev. 01 - ed. 10/2016 6.8 temperature probe calibration once inside the technical menu, the boiler temperature will automatically set to 120°c. It is possible to check the condition of the electrical heating element via the “°c” symbol; if it is fixed, the he...

  • Page 21

    Espresso coffee machines 19 40 lsi 024 - rev. 01 - ed. 10/2016 6.10 washing the boiler with the machine on, press and hold down the “hot water delivery” key for 3 seconds. The machine dispenses water from the wand for about 2 minutes, then restore the correct water level in the boiler. 6.11 group wa...

  • Page 22

    Espresso coffee machines 20 40 lsi 024 - rev. 01 - ed. 10/2016 7 technical assistance program – g.A. - (optional) the scheduled technical assistance program makes it possible to keep some appliance parameters under control, making it possible to set a minimum threshold after which an alarm signal is...

  • Page 23

    Espresso coffee machines 21 40 lsi 024 - rev. 01 - ed. 10/2016 to indicate that the technical assistance is deactivated. To enable one or both available controls, proceed as follows: hold down the button for about 3 seconds , this opens the service menu and the display will read: where “ y ” (yes) w...

  • Page 24

    Espresso coffee machines 22 40 lsi 024 - rev. 01 - ed. 10/2016 take note! The set number is not a count of the number of cups of coffee delivered by the appliance, it is just a control over the solenoid valve insertion cycles for the groups and therefore, for example, 100 solenoid valve cycles do no...

  • Page 25

    Espresso coffee machines 23 40 lsi 024 - rev. 01 - ed. 10/2016 after confirming the setting, the program passes onto the settings for the softener filter menu. The display will show: where “ y ” (yes) will be flashing. To select “ n ” (no) press one of the 2 arrow keys , “ n ” will start to flash. I...

  • Page 26

    Espresso coffee machines 24 40 lsi 024 - rev. 01 - ed. 10/2016 where the first “0” on the right is flashing. Pressing the button will increase the number (0 - 9), while pressing the button moves to the most important digit on the left (the selected digit will flash to show that it can be changed). O...

  • Page 27

    Espresso coffee machines 40 25 lsi 024 - rev. 01 - ed. 10/2016 setting the softener filter parameters. To access the menu to set softener filter parameters, press and hold down all three keys for 3 seconds. The display will read: where “ 0.54 ml ” is the correspondence between a flow meter pulse and...

  • Page 28

    Espresso coffee machines 26 40 lsi 024 - rev. 01 - ed. 10/2016 where “ 1750 ml ” is the correspondence between 1 minute of operation of the automatic boiler refill system and the amount of water introduced, given in millilitres. Pressing the buttons increases/decreases the setting ( 1000 ml – 2000 m...

  • Page 29

    Espresso coffee machines 27 40 lsi 024 - rev. 01 - ed. 10/2016 7.1 series s40 alarms manager this series of symbols informs of any machine operation anomalies. In case of machine lock alarm, the main display and the delivery group displays show the only central lines switched on. Symbol alarm type p...

  • Page 30

    Espresso coffee machines 28 40 lsi 024 - rev. 01 - ed. 10/2016 symbol alarm type problem possible solution m.A.T. System temperature probe failure. M.A.T. Temperature probe short circuit or interrupted. Check the machine’s m.A.T. System. Take note! When this alarm is triggered, it is in any case pos...

  • Page 31

    Espresso coffee machines 29 40 lsi 024 - rev. 01 - ed. 10/2016 7.2 notes for the service engineer setting the electronic control board the electronic control board can be set to manage two different water level controls (probe or float) and to control the two different group delivery versions: autom...

  • Page 32

    Espresso coffee machines 30 40 lsi 024 - rev. 01 - ed. 10/2016 7.3 electronic expansion board when replacing the electronic expansion boars, always make sure that the mc1 contact is open before switching on the machine. With the machine in standard configuration, the dip 2 of kd1 must be set to off....

  • Page 33

    Espresso coffee machines 40 31 lsi 024 - rev. 01 - ed. 10/2016 7.3.1 check/calibration of pump motor pressure below are the operations to be performed when checking and/or calibrating the pres- sure of the pump motor inside the machine. 1. Remove the drip tray and grating. 2. Remove the 2 bottom pro...

  • Page 34

    Espresso coffee machines 40 32 lsi 024 - rev. 01 - ed. 10/2016 7.3.2 checking/calibrating the opening pressure for the expansion valve the following section lists the checks/calibration operations needed for the expan- sion valve. With the machine on and at the right temperature, press the delivery ...

  • Page 35

    Espresso coffee machines 40 33 lsi 024 - rev. 01 - ed. 10/2016 2. Remove the 2 bottom protective caps and the 2 allen screws that fasten the bot- tom drain cover and then remove the drain cover and remove it. 3. Remove the plate covering the system by loosening the two fastening screws. To increase ...

  • Page 36

    Espresso coffee machines 40 34 lsi 024 - rev. 01 - ed. 10/2016 8 disassembly of the machine 8.1 disassembly of the side panels 1. Remove the glass side panels by lifting them as shown in the figure. 2. Using a screwdriver, slacken the upper fixing screws of the side panels as shown in the figure. 3....

  • Page 37

    Espresso coffee machines 40 35 lsi 024 - rev. 01 - ed. 10/2016 4. Pull the side panel away from the machine and remove it as shown in the figure. 5. Proceed in the same way for the other side panel. 6. Reposition the elements previously removed in reverse order. Fig. 37.

  • Page 38

    Espresso coffee machines 40 36 lsi 024 - rev. 01 - ed. 10/2016 8.2 disassembly of the upper front panel 1. Remove the side glass panels by lifting them as shown in the figure. 2. Unscrew and remove the steam dispensation control lever knobs as shown in the figure. 3. Using a screwdriver, slacken the...

  • Page 39

    Espresso coffee machines 40 37 lsi 024 - rev. 01 - ed. 10/2016 3. Using a screwdriver, slacken the lower fixing screw of the front panel as shown in the figure. 4. Slide the front panel forwards until it stops. 5. Rotate the front panel as shown in the figure. 6. Reposition the elements previously r...

  • Page 40

    Espresso coffee machines 40 38 lsi 024 - rev. 01 - ed. 10/2016 1. Proceed to disassemble the upper front panel as previously described 2. Using a screwdriver slacken the fixing screws of the control panel as shown in the figure and disconnect the cables between the panel and the front cpu. 3. Press ...

  • Page 41

    Espresso coffee machines 40 39 lsi 024 - rev. 01 - ed. 10/2016 8.3 disassembly of the drainage cover panel 1. Remove the water collection basin and the relative grill. 2. Remove the 2 lower protection caps and the 2 allen screws relative to the fixing of the lower drainage cover panel and remove it....

  • Page 42

    Espresso coffee machines 40 40 lsi 024 - rev. 01 - ed. 10/2016 1. Remove the filter holders from the machine. 2. Using a screwdriver, rotate the two screws a quarter of a turn that are positioned to the side of the coffee dispensing group cover. 3. Remove the coffee dispensing group cover by sliding...

  • Page 43

    Espresso coffee machines 40 41 lsi 024 - rev. 01 - ed. 10/2016 4. Using a screwdriver, remove the 4 screws at the side of the coffee dispensing group. 5. Disconnect the cables and pull the coffee dispensing group downwards. 6 . Reposition the elements previously removed in reverse order. Fig. 53 fig...

  • Page 44

    Espresso coffee machines 40 42 lsi 024 - rev. 01 - ed. 10/2016 8.4 disassembly of the upper cover 1. Remove the glass side panels by lifting them as shown in the figure. 2. Remove the grills of the cup warmer plate by lifting them as shown in the figure. 3. Using a screwdriver, remove the fixing scr...

  • Page 45

    Espresso coffee machines 40 43 lsi 024 - rev. 01 - ed. 10/2016 4. Remove the front plate of the cup warmer plate as shown in the figure. 5. Using the rear part as the fulcrum, pull up the rear plates of the cup warmer plate and remove them as shown in the figure. 6. Using a screwdriver, remove the f...

  • Page 46

    Espresso coffee machines 40 44 lsi 024 - rev. 01 - ed. 10/2016 7. Remove the upper cover as shown in the figure. 8. Reposition the elements previously removed in reverse order. Fig. 71.

  • Page 47: Diagrams

    Espresso coffee machines 45 40 lsi 024 - rev. 01 - ed. 10/2016 diagrams.

  • Page 48

    Espresso coffee machines 46 40 lsi 024 - rev. 01 - ed. 10/2016 9. Diagrams for electronic board connections 9.1 expansion board key: smat m.A.T. System temperature probe (optional). P5 m.A.T. System button connection (optional). Counter display connection for 1st group from the right. Ev mat connect...

  • Page 49

    Espresso coffee machines 47 40 lsi 024 - rev. 01 - ed. 10/2016 9.2 classic/ suprema cpu.

  • Page 50

    Espresso coffee machines 48 40 lsi 024 - rev. 01 - ed. 10/2016 key: mp connection for pump motor. Rs connection for static relay. Phase neutral 10 v transformer outlet connection. K1 k2 connection for static relays. Sl level probe connection. St boiler temperature probe connection. Sw dip configurat...

  • Page 51

    Espresso coffee machines 49 40 lsi 024 - rev. 01 - ed. 10/2016 9.3 front led display key: m connection for led and program- ming button pad for the control panel. Ser1 connection for classic/suprema cpu..

  • Page 52

    Espresso coffee machines 50 40 lsi 024 - rev. 01 - ed. 10/2016 9.4 group led display key: counter in expansion control board connection. Counter out group display connection..

  • Page 53

    Espresso coffee machines 51 40 lsi 024 - rev. 01 - ed. 10/2016 9.5 wiring diagram.

  • Page 54

    Espresso coffee machines 52 40 lsi 024 - rev. 01 - ed. 10/2016 key: mp motor pump. Rs cup warmer heating element. He boiler heating element. Eval automatic water filling solenoid valve. Ev1 solenoid valve for 1st group from the right. Ev2 solenoid valve for 2nd group from the right. Ev3 solenoid val...

  • Page 55

    Espresso coffee machines 53 40 lsi 024 - rev. 01 - ed. 10/2016 9.6 hydraulic diagram.

  • Page 56

    Espresso coffee machines 54 40 lsi 024 - rev. 01 - ed. 10/2016 key: r water cock (put in place by end customer). Rp pressure reducer (optional). A softener (optional). F impurity filter (optional). P motorised pump. G1 water mains and motorised pump pressure gauge. Nv check valve. Ve expansion valve...

  • Page 57

    Espresso coffee machines 55 40 lsi 024 - rev. 01 - ed. 10/2016 all la spaziale espresso machines are made with a heat exchanger system between the boiler and the coffee delivery group. A special patented system, the only one in the world, for heat adjustment of the delivery group, based on the circu...

  • Page 58

    Espresso coffee machines 56 40 lsi 024 - rev. 01 - ed. 10/2016 10 technical data fig. 72 dimensions and weight s40 2 gr 3 gr 4 gr l 850 1080 1320 h 600 600 600 p 560 560 560 weight kg 85 100 115 power supply rating and absorption s40 2 gr 3 gr 4 gr volt 220/240/400 220/240/400 220/240/400 hz 50/60 5...

  • Page 59

    Espresso coffee machines 57 40 lsi 024 - rev. 01 - ed. 10/2016.

  • Page 60

    Espresso coffee machines 58 40 lsi 024 - rev. 01 - ed. 10/2016.

  • Page 62: La Spaziale S.P.A.

    La spaziale s.P.A. Via e. Duse, 8 40033 casalecchio di reno bologna - (italy) ✆ +39 051 611.10.11 +39 051 611.10.11 +39 051 611.10.40 info@laspaziale.Com espresso coffee machines.