Hypercolor 575 cym continuous colour changer wash luminaire user’ s manual release 1.0 this manual must be considered an integral part of the projector..
1 before connecting and using the projector, it is important to read carefully all the instructions in this manual. Qualified personnel only, in compliance with all the security laws, can do the installation, the maintenance and the utilisation of this projector. Before connecting the projector, mak...
2 general description as shown in figure 1, the hypercolor 575 is made up of the following parts: 1. Auxiliary support/ rear panel 2. Cooling fan 3. Optional anchoring bracket 4. Anchoring bracket 5. Projector body 6. Front panel 7. Top cover knob features and dimensions voltage rating 230 v rated c...
3 rear panel as shown below, the following elements can be seen on the rear panel: 4 1 0 dmx out dmx in 1,6at 6,3at a 4,5 v 230 hz 5060 ce signal led lamp msr/msd 575w gx 9,5 hypercolor 575 dmx channel assignement ch1= cyan ch2= yellow ch3= magenta ch4= dimmer ch5= shutter ch6= special functions d m...
4 no more than three identical boxes can be stacked one on top of the other. Keep the original packing for possible shipments in the future. Storage the projector, in its original packing, must be kept in covered, dry areas with a temperature between -10° c and +50° c. Handling the projector, with o...
5 connections power supply use the cable provided inside the special junction box. The power line must be protected by a differential magneto thermal circuit breaker, while metal parts that might be electrically charged through the projector must be grounded. Hypercolor 575 absorbs 940w at 230v. Mak...
6 dmx channel assignment channel function 01 cyan 02 yellow 03 magenta 04 dimmer 05 shutter 06 special functions dmx values (the values % are approximated) channel 1 = cyan percent values decimal values 0 % >>> open =0 >>> 100% cyan =255 option: personality dip-switch n°01 in position on 0 % >>> cya...
7 channel 5 = shutter percent values decimal values 0 > 10% open =0 11 >20 % closed =40 21%>>>> strobe effect min speed =54 >>> 100% strobe effect max speed =255 option : personality dip-switch n°03 in position on 0 > 10% closed =0 11 > 20% open =40 21%>>> strobe effect min speed =54 >>> 100% strobe...
8 stand-alone functions hypercolor can work in stand-alone both single and in banks, that means without the need of a control unit, in master/slave function, since any luminaries can be master of a bank, it becomes able to control synchronously all the other hypercolor fixtures and to manage a menu ...
9 maintenance caution safety guards, lenses, and filters must be replaced if they are visibly damaged to the point that they become ineffective (for example, if they have deep slashes or cuts). The lamp must be replaced if damaged, cracked, or deformed by the heat. Planned maintenance at user’s char...
10 frequency it is recommended to clean the projector every two months to ensure efficiency and performances. If the projector is used in particularly smoky or dusty areas, clean the projector more frequently. 1. Use a (soft) compressor to remove the dust from the front areas and from the fan (keepi...
11 troubleshooting problem possible cause solutions projector will not turn on no mains power no power to the projector burned-out fuse make sure the mains power is on and the circuit breaker hasn’t been triggered make sure the switch on the back of the projector is on. Make sure the top lid is tigh...
12 optional and beam angle barn doors kit the barn doors mounting kit is supplied if requested as a optional, the mounting process is very easy: 1- unscrew the 4 ph screws from the front panel. 2- insert the 4 spacers you will find in the barn door kit and firmly tight. 3- position the barn doors an...
