- DL manuals
- Lassco
- Office Equipment
- Spinnit EBM-2.1
- User Manual
Lassco Spinnit EBM-2.1 User Manual
Summary of Spinnit EBM-2.1
Page 1
Provided by http://www.Mybinding.Com http://www.Mybindingblog.Com lassco spinnit ebm-2.1 paper drill user's manual.
Page 2
Before operating this equipment, please read these instructions completely and keep these operating instructions for future reference. Serial number: date of purchase: dealer: address: telephone number: 485 hague street, rochester, ny 14606 u.S.A. Tel: 585-436-1934 fax: 585-464-8665 www.Lasscowizer....
Page 3
Table of contents introduction operating instructions maintenance trouble shooting guide introduction....................................................................... Shipping damage inspection............................................ Page 02 page 02 safety information safety instructions.....
Page 4
Introduction shipping damage inspection page 02 thank you for your purchase of the spinnit ebm-2.1 paper drill. Lassco-wizer has been designing and manufacturing proven performance equipment for the graphic arts, office, screen printing, sign, awards and engraving industries for over 60 years. We as...
Page 5
Safety information page 03 all operators must read and understand the users manual and all other safety instruc- tions before using this equipment. If after reading the manual you are still uncertain about use, please contact a service technician for assistance. If you need contact information for a...
Page 6
Setting up your machine loose materials inventory page 04 remove and inspect the following items: 2-3/4 3-1/2 2-3/4 4-1/4 items are not to scale ez-114a: table assembly (1) ez-115a: backgauge (1) ez-1016 pattern bars (set of 5) fm4-4007: side stop screws (4) fm4-4006: paper side stops (2) ebm2-1048:...
Page 7
Setting up your machine table assembly installation page 05 grasping the table and depressing the release handles to unlock the table pin, slide the v-bars located on the underside of the table into the v-rollers on the base of the machine as shown. Step #1 attach the second table stop (ez-1014) to ...
Page 8
Setting up your machine backgauge assembly page 06 step #4 step #3 paper side stops attach the paper side stops (fm4-4006) using two side stop screws (fm4-4007) each. Position the paper side stop as desired and tighten down with light pressure. Step #5 attach the backguage to the table by hooking th...
Page 9
Setting up your machine chip bag pattern bars page 07 your ebm-2.1 comes with five pattern bars included. Four common patterns and one blank pattern as shown. Insert a pattern bar by loosening the pattern bar stop (ez-1022) and inserting the desired pattern into the slot on the pattern bar guide as ...
Page 10
Operating instructions drill bit removal and installation page 08 remove the hole guard which is attached to the chuck. This is done by grasping the bent end and sliding the guard off. Step #1 using the chuck release key (ebm-32), insert the tapered end facing down into the chuck hole. With a clockw...
Page 11
Operating instructions leveling the drill bits page 09 to level the drill bits to the table, first loosen the leveling knob on the right hand side of the machine as shown. Pull down on the handle to raise the table until the hollow drill bit is just touching the drill strip (ebm2-1034). Hold the han...
Page 12
Operating instructions clearing the chips page 10 it is important to clear the chips from the drill bit when you are finished drilling so that the chips won’t clog the drill bit. Make sure to turn the power off on the machine. Place the chip clearer (cc-2) below the hollow drill bit using one of the...
Page 13: Maintenance of This Machine.
Maintenance page 11 note: refer to your trouble shooting guide for problem solving caution: keep fingers from between lift components. Observe all safety precautions during the preventative maintenance of this machine. Every 6 months remove back panel and lubricate the lift pin with a good grade of ...
Page 14
Trouble shooting guide page 12 problem cause correction drill bit not concentric. Foreign material in chuck or in drill plug. Inspect and clean. Drill bit is bent. Replace drill bit. Drill bit not seated in chuck properly. Reinsert drill bit correctly. Chuck is not tight to spindle. Tighten set scre...
Page 15: See Parts List On Page 15
Parts diagrams page 13 front, back, and side view see parts list on page 15.
Page 16: See Parts List On Page 15
Parts diagrams page 14 interior front and back see parts list on page 15.
Page 17
Parts diagrams page 15 parts list ez-108a: handle assembly fm5-5006: rocker switch (on/off) ez-117a: shroud assembly fm5-5003: chuck fm5-5011: chuck release guard hollow drill bit ebm2-0111a: pressure foot assembly 3s-14: table scale ez-1010l: table release handle (left) ez-1010r: table release hand...