Lawmate DD9004 Manual

Names and Parts

(1)

(2)

Wireless Camera Hunter Operation

Manual 

V1.0

Law Enforcement Products Manufacturer

LawMate

LCM Operation Interface

(3)

■

Enter setting:

    Slide the POWER key on side of the unit to turn on the device, press and hold the    

    SETUP key for 3 seconds then release it. The icon will be blinking on the LCM (the 

    smaller screen), scroll the SETUP key upward or downward to change setting.

■

Change setting:

    Press the SETUP key once to confirm change and to move on next setting.

■

Exit setting:

    Press and hold the SETUP key again for 3 seconds.The device will return to scanning mode. 

UP

PU

SH

D

O

W

N

67.00 mm

96

.0

0

m

m

21.20 mm

1.2GHz ant. mount

   2.4 & 5.8GHz ant. mount

SETUP key

LCD screen

LCM screen

Signal In/Out socket

DC 5V In

Power Switch

■

Installing the battery

Remove battery cover on back of the 

unit. Slide the supplied battery at 

about 15 degree angle to the battery 

compartment. Please be aware of +/- 

direction.

■

Charging the battery:

   Connect the supplied power adaptor to an AC wall outlet and attached the other end 

   of the cord to the DC 5V In socket.

■

Power indication:

   When charging the battery, a red color LED light will illuminate. Once the battery is 

   fully charged, the LED light will turn off.  (The charging time is approximately 3 ~ 4 

   hours depending on the battery remaining power.) Please charge the battery for 8 

   hours on the first-time use.

■

Antenna connector

Plug antenna 1 to port 1 and antenna 2 to port 2. You can 

find the indication printed on the antennas as well as on 

the ports. Turn the antenna’s base clockwise until it locks

into place.

■

Power switch:

    The power switch is on the side of the device. When the unit is turned on, it starts 

    scanning the signal automatically. Make sure the antenna is screwed tightly to its 

    allocated position to avoid poor reception.

■

Frequency scanning:

  Whenever a wireless A/V signal is detected, the image will be displayed on the 

  screen and stays for few seconds. The length of time depends on your setting. You 

  have the option to lock the channel by scroll upward or downward the SETUP key on 

  side of the device to lock the channel or else it will pass on and continue scanning. 

■

Manual scanning:

  Scroll upward or downward the SETUP key to scan manually.

■

Low battery alert:

  When the battery gets low, the battery icon will blink. Charge your battery immediately.

■

External video input:

  To connect external video to the device, change the setting to EX mode. Make sure 

  the connector is plugged properly to the Signal In/Out socket on side of the device, 

  otherwise it will result non-signal input.

1

2

EX

60

30

30

30

30

4

2

60

30

30

2

MH

M

B

MH

MH

M

ML

L

UH

B

30

30

30

30

30

30

30

1080

 00

1080

30

1080

30

UH

1080

2

B

30

a

00

   Signal Dwell 

   Time

EXT. AV input mode

30 Sec. interval mode

60 sec. interval mode

Standard scanning mode

8 seconds

4 seconds

2 seconds

L (Low/-20dBm)

ML (Medium Low

/-30 dBm)

H (High/-60dBm)

MH (Medium High

/-50dBm)

M (Medium/-40dBm)

UH (Ultra High

 / -75dBm)

Alert on/Vibrate Off

Alert on/Vibrate On

Alert Off/Vibrate Off

Alert Off/Vibrate On

Scanning 

Mode

Receiver 

Sensitivity

   Audio & Vibration

   Alert Setting

00

DD9004