Summary of Show Fogger Pro
Page 1
Lemaitrefx.Com show fogger pro operations manual v05.01.05.
Page 2
Lemaitrefx.Com page 1 introduction page 2 warning page 3 technical specifications page 4 operating procedure page 5 remote handset operations page 5 remote handset led indicators page 5 remote and external control features page 6 show fogger tube change procedure page 7 maintenance page 8 recommende...
Page 3
Lemaitrefx.Com the show fogger pro is a microprocessor controlled, water base fog generating system. The microprocessor is responsible for the following control elements - monitoring the heat exchanger temperature. Driving the heater within the heat-exchanger. Driving the fluid pump unit, relating f...
Page 4
Lemaitrefx.Com 2 m.S.D.S. Available at www.Lemaitrefx.Com important safety instructions : do not touch or place hands, expose skins, within 50 cm. Of discharge nozzle. Important safety instructions : do not remove the outer case until power has been disconnected from the machine. Important safety in...
Page 5
Lemaitrefx.Com model: show fogger pro type: water base fog generating system size: height: 9 1/2” 24 cm. Width: 9 3/8 23.8 cm. Length:22 1/2 57.1 cm. Net weight: 11.3 kg. 25 lbs. Weight with fluid 15.8 kg. 35 lbs. Power rating: 110 volt a.C.50/60 hz 12 amps 240 volt a.C.50/60 hz 6 amps included: ful...
Page 6: Operating Procedure
Lemaitrefx.Com 1) the show fogger pro must only be connected to a grounded mains supply capable of sustaining at least 15 amps. The supply should be ‘clean’ and free of interference. 2) open a container of le maitre fog fluid , remove cap and break foil seal (if provided). Remove cap from show fogge...
Page 7
Lemaitrefx.Com 5 the fog output time is set using the ‘duration’ control (0 to max) and the time between successive fog outputs is set using the ‘interval control (0 to max). Continual flow can be achieved if ‘interval’ setting is at 0. The standard remote handset cable may be extended from the mach...
Page 8
Lemaitrefx.Com 6 1. Remove the six screws from the case. Four are under the lip at mid level and two are on top. Remove the bolt from the front of the fluid jug. Slide the upper cover forward and remove it from the machine. Lift the jug up and out of the way. 2. Remove the two screws from the front ...
Page 9
Lemaitrefx.Com 7 the casing of the show fogger pro is steel with a powder paint coating. To clean simply wash with mild soap and warm water. With normal use we do not recommend flushing or cleaning the heat exchanger, with the use of genuine le maitre fluids. Using high quality le maitre fluid shoul...
Page 10
Lemaitrefx.Com 8 pro beam (long lasting) fog fluid : we have had many compliments on our fog fluid but many of our customers would like it to hang longer so we introduced the “long lasting fluid”. It is still odourless but a little less white than our “director’s choice”. It hangs in the air 2 - 3 t...
Page 11
Lemaitrefx.Com warranty: all warranty is one year parts and labour unless specified and is on manufacturer defect only. Abuse or poor maintenance is not accepted. Le maitre fluids must always be used. Any trace of other fluids will automatically void all warranties. Accept no substitutions as there ...
Page 12
Lemaitrefx.Com 1. Ensure that operation of the machine is supervised by suitably trained and authorised personnel. 2. Do not modify the machine or use a machine which has been damaged in any way. 3. Allow sufficient air circulation around the machine at all times. 4. Protect the show fogger pro from...