- DL manuals
- M Box
- Amplifier
- 0E-IA1250
- Manual
M Box 0E-IA1250 Manual - Rear Panel Features
8
8. POWER ON/OFF SWITCH - One, switch. Set to ON position to turn power to the amp ON. Set to OFF
position to turn power to the amp OFF.
9. VOLTAGE SELECT SWITCH - One, switch. Select either 110V-120V or 220V-240V as appropriate for local
AC line voltage. Please confirm local voltage prior to use or making changes to the setting.
10. AC MAINS - One, three-prong socket. Use the supplied 3-pin ground power cable to connect the unit to an
external AC power supply.
11. FUSE - One, replaceable fuse. For 110V-120V/60Hz use a T10.0AL/250V fuse. For 220V-240V/50Hz use a
T5.0AL/250V fuse.
12. RS232 TERMINAL - One, DB9F terminal. Connect to an automation system or other controller for two-way
communication with and control of the 0E-IA1250.
13. REMOTE BYPASS - One, six position DIP switch. Set to OFF to allow IR/RS232 control of the selected
zone. Set to ON to block IR/RS232 control of the selected zone.
14. ZONE LINE IN - Twelve, RCA jacks. Connect to the L & R line level OUTs on an audio source that is to be
dedicated to a specific zone.
15. ZONE AUDIO LIMITER - Six, push buttons. Press to activates a -20dB input limiter, for both channels, to
help reduce the level of accidental audio peaks and clipping distortion by zone. Leave in the OUT position
to pass audio through unprocessed, press IN to activate the input limiter.
16. STEREO/BRIDGED - Six, push buttons. Sets zone amplifier output to stereo/bridge mode. This switch
works in conjunction with the zone speaker connections and 8Ω/4Ω - 70V/100V switch position.
Please see sections: Zone Speaker Terminal and 8Ω/4Ω - 70V/100V Switch, previous, for important
information.
Stereo - For stereo signals, leave switch in the OUT (Stereo) position. This applies to all connections in
the 8 Ohm/4 Ohm and 70V/100V configurations.
Bridged - ONLY press this button when using the BRIDGE 8Ω connections in a given zone.
CAUTION: In Bridged mode, the amplifier will encounter a load that is about one half of its
actual value. A 4Ω load would therefore be 2Ω to a bridged amp and if the amplifier isn’t
designed to run safely into such a low impedance (which the 0E-IA1250 is not) damage may
occur to the amplifier. DO NOT CONNECT A 70V SPEAKER CIRCUIT WHILE IN BRIDGE MODE.
The output will be 140V, well beyond spec for a 100V system. Any damage to the amplifier
caused by this configuration is not covered under warranty.
17. AUDIO BUS - One, plug-in screw terminal. Mono, unbalanced input. This input will send the Audio IN
signal to all zones switched to Bus using the Line/Bus Trigger IN. It can also send the Bus Audio IN signal
to another 0E-IA1250 via the Audio Bus OUT.
Rear Panel Features
Summary of 0E-IA1250
Page 1
Right left right left right left right left right left right left oe-ia1250 12 channel 6 zone integrated amplifier 0e-ia1250
Page 2
2 • explanation of graphical symbols the lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to per...
Page 3: Table of Contents
3 table of contents important safety instructions ............................................................................................................ 2 table of contents ............................................................................................................................
Page 4: Introduction
4 introduction congratulations and thank you for purchasing the w box technologies 0e-ia1250 12 channel amplifier. The 0e-ia1250 is, at its core, a twelve channel audio distribution amp....But it can also do so many other things. The 0e-ia1250 is a twelve channel audio distribution amp that can be c...
Page 5: Features
5 features • each zone can independently select a zone-specific stereo audio source or the global mono audio bus input (unbalanced) • each zone can be independently configured for stereo 4 ohm/8 ohm mode, high powered bridged 8 ohm mode or 70v/100v mode for total flexibility within a given installat...
Page 6: Front Panel Features
6 2 1 1 3 1. Rack ears - two, optional rack ears. The 0e-ia1250 is 2u rack height. If rack mounting, leave one rack space above and below for air flow. The rack ears can be removed for shelf mount if desired. 2. Peak output leds - six, red leds indicate that the amplifier is within 5% of the maximum...
Page 7: Rear Panel Features
7 right left right left right left right left right left right left 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1. System 70/100 volt select - one, switch. Slide switch to select between 70v and 100v for a high- voltage audio distribution system. This setting will affect all zones in 70v/100v mode. Se...
Page 8: Rear Panel Features
8 8. Power on/off switch - one, switch. Set to on position to turn power to the amp on. Set to off position to turn power to the amp off. 9. Voltage select switch - one, switch. Select either 110v-120v or 220v-240v as appropriate for local ac line voltage. Please confirm local voltage prior to use o...
Page 9: Ir Remote Control
9 ir remote control the 0e-ia1250 ir remote control controls the individual zones on the 0e-ia1250. It can also be used to teach ir commands to a programmable, integrated ir remote, zone control system or other ir routing device. All zones are configured for the same codes, so use of a multi-zone co...
Page 10: Installation
10 installation 1u rack vent above 0e-ia1250 1u rack vent below 0e-ia1250 1. The 0e-ia1250 is convection cooled. It depends on the natural free flow of air up through the slot perforations in the bottom plate, over the internal heat dissipating fins, then out the top cover, for adequate cooling. 2. ...
Page 11: Wiring Infrastructure
11 wiring infrastructure speaker wire the 0e-ia1250 is a flexible multi-channel amplifier capable of many different applications. The application for a given system, or even different amp configurations for different zones within a single system can create different requirements for speaker wire run...
Page 12: Connections
12 connections speaker connections the 0e-ia1250 has three amplifier modes for zone speaker connections. Bridged 8 ohms, 4/8 ohms stereo and 70v/100v. Any mix of amplifier modes is allowable in different zones...As long as they are configured correctly. Never change the 70v/100v high voltage speaker...
Page 13: Connections
13 connections 70v/100v this configuration creates a stereo 70v speaker zone. (30w/channel) a 70v/100 v system utilizes speakers with special taps that set the wattage/ volume of each speaker. 70v/100v speaker system are wired using a daisy-chain configuration where the amp feeds a speaker, then tha...
Page 14: Connections
14 connections audio connections zone line in this connection is an input for a dedicated zone line-level audio source. If multiple line level audio sources are required in a zone, use an audio switch on the zone line in or use a multi-source, multi- zone controller if multiple audio sources are req...
Page 15: Control Connections
15 control connections zone ir in this connection allows ir control of the connected zone for zone power, volume, mute, line/bus, etc using the commands from the 0e-ia1250 ir remote and a connected ir control system. Ir receiver ir connecting block 12vdc power supply ir remote 0e-ia1250 zone ir inpu...
Page 16: Connections
16 zone mute this connection allows voltage control of zone mute. Applied voltage (+3 to +30vdc @1ma) will mute the zone speaker output. When the voltage is cut, zone speaker output is restored. 1. Mute/gnd - using a 2-conductor stranded, non-shielded cable, connect +dc voltage and gnd from the trig...
Page 17: Connections
17 master control in this connection allows voltage control of 0e-ia1250 on/off. Applied voltage (+3 to +30vdc @1ma) will turn the amp on. When voltage is cut, the amp will turn off. (off, not standby.) note: the power switch must be in the off position when using this feature. With this feature the...
Page 18: Settings
18 this section covers all of the settings that need to set correctly in order for the 0e-ia1250 to function properly. 70/v100v high voltage speaker output sets all zone speaker connections configured for 70v/100v to either 70 volts or 100 volts. This switch is used in conjunction with both the ac v...
Page 19: Settings
19 remote bypass the remote bypass switch allows/prevents ir and rs232 control by zone. When the switch is in the on position (bypass zone) the zone will not respond to ir or rs232 commands. When the switch is in the off position, (do not bypass zone) the zone will respond to ir and rs232 commands. ...
Page 20
20 l r in out 1 2 3 4 5 6 zone 1 ir receiver zone in ceiling speakers zone 2 zone in ceiling speakers zone 3 zone in ceiling speakers zone 4 zone in ceiling speakers zone 5 zone in ceiling speakers zone 6 zone in ceiling speakers 0e-ia1250 audio distribution amp a/v receiver or other audio source sw...
Page 21: Operation
21 how the 0e-ia1250 is controlled is dependent upon how it is being used. Three basic modes will be explained: voltage controlled, ir controlled and rs232 controlled. There are of course, variations on these three basic control modes that can utilize some options from the other modes. Look for the ...
Page 22: Operation
22 1. On/off - press the power button on the 0e-ia1250 ir remote to turn the zone on. Press again to turn the zone off. 2. Bus/line - press the bus button to select the source connected to the 0e-ia1250 audio bus in (if used). Press the line button to select the source connected to the local zone li...
Page 23: Rs232 Commands
23 0e-ia1250 rs232 commands name command remarks zone power !{z#} pr{0/1}+ to turn on zone 2: !2pr1+ to turn off zone1: !1pr0+ zone power toggle !{z#} pt+ zone volume !{z#} vo{v#}+ zone vol. Inc. !{z#} vi+ zone vol. Dec. !{z#} vd+ zone input select !{z#} is{0/1}+ to select bus: !2is0+ to select line...
Page 24: Rs232 Commands
24 0e-ia1250 rs232 commands name command remarks bass decrement !{z#} bd+ balance !{z#} ba{b#}+ balance step left !{z#} bl+ balance step right !{z#} br+ zone activity auto update ! Za{0/1}+ enable/disable auto update of the zone information when zone activity is detected. (see below for format of th...
Page 25: Rs232 Queries
25 rs232 queries 0e-ia1250 rs232 queries name query response example response explanation zone volume ?{z#}vo+ ?{z#}vo{v#}+ ?4vo49+ zone 4 is currently at volume level 49. Channel volume ?{c#}ch+ ?{c#}ch{v#}+ ?4vo49+ channel 4 is currently at volume level 49. Mute ?{z#}mu+ ?{z#}mu{0/1}+ ?8mu1+ zone ...
Page 26: Rs232 Queries
26 rs232 queries zone activity and zone status za – zone activity auto update enable command. Format - !Za{0/1}+ zs – zone status query. Format - ?(z#}zs+ zone activity auto update enable command the activity update will cause the system to send out the complete zone state whenever something in the ...
Page 27: Rs232 Settings
27 rs232 settings 0e-ia1250 volume level settings 0e-ia1250 setting attenuation level 38 0 37 -1.25 36 -2.50 35 -3.75 34 -5.00 33 -6.25 32 -7.50 31 -8.75 30 -10.00 29 -11.25 28 -12.50 27 -13.75 26 -15.00 25 -16.25 24 -17.50 23 -18.75 22 -20.00 21 -21.25 20 -22.50 19 -23.75 18 -25.00 17 -27.50 16 -30...
Page 28: Rs232 Settings
28 rs232 settings 0e-ia1250 treble/bass level settings 0e-ia1250 setting level (+/-db) 14 +14 13 +12 12 +10 11 +8 10 +6 9 +4 8 +2 7 0 6 -2 5 -4 4 -6 3 -8 2 -10 1 -12 0 -14 0e-ia1250 left/right balance settings 0e-ia1250 setting left speaker +/- ddb right speaker +/-db 0 0 mute 1 0 -37.5 2 0 -36.25 ....
Page 29: Specifications
29 specifications audio sections continuous output power ................................................. 30w per channel 8ohms at 1khz thd 0.1% 50w per channel 4ohms at 1khz thd 0.1% 100w bridged 8ohms at 1khz thd 0.1% 30w per channel 70v/100v at 1khz thd 0.1% total harmonic distortion ..............
Page 30: Limited Warranty
30 limited warranty 1. Limited warranty a. General subject to the terms and conditions of this limited warranty, from the date of sale through the period of time for product categories specified in section 1(b), adi warrants its w box technologies products to be free from defects in materials and wo...
Page 31: Limited Warranty
31 limited warranty b connectors limited lifetime bus terminals limited lifetime extension cords limited lifetime hdmi cables limited lifetime jacks, cords and intrusion communication accessories limited lifetime patch cables limited lifetime raceway conduit limited lifetime wire ties limited lifeti...
Page 32: Limited Warranty
32 4. Returns subject to the terms and conditions listed below, during the applicable warranty period, adi will replace product or provide a credit at purchase at its sole option free of charge any defective products returned prepaid. Any obligations of adi to replace limited lifetime warranty produ...
Page 33: Notes
33 notes.
Page 34
34 • explication des symboles graphiques le symbole représentant un éclair se terminant par une flèche, dans un triangle équilatéral, a pour objectif de signaler la présence d’une source de « tension dangereuse » non isolée dans le boîtier du produit et suffisamment puissante pour entraîner des risq...
Page 35: Table Des Matières
35 table des matières consignes de sécurité importantes................................................................................................ 34 table des matières ........................................................................................................................... 35...
Page 36: Introduction
36 introduction félicitations et merci d’avoir acheté l’amplificateur à 12 canaux 0e-ia1250 de w box technologies! L’0e-ia1250 est essentiellement un ampli de distribution audio à douze canaux....Mais il a un tas d’autres fonctions. L’0e-ia1250 est un ampli de distribution audio à douze canaux confi...
Page 37: Caractéristiques
37 caractéristiques • chaque zone peut sélectionner indépendamment une source audio stéréo spécifique ou l’entrée de bus audio mono globale (non équilibrée) • chaque zone peut être configurée indépendamment pour le mode stéréo 4 ohms//8 ohms,le mode haute intensité avec passerelle de 8 ohms ou le mo...
Page 38: Éléments Du Panneau Avant
38 2 1 1 3 1. Oreilles de montage - deux oreilles de montage en option. L’0e-ia1250 est une hauteur de baies 2u. Si vous installez l’appareil sur baie, laissez un espace au-dessus et en dessous de la baie pour laisser passer l’air. Si vous le souhaitez, vous pouvez enlever les oreilles de montage po...
Page 39
39 right left right left right left right left right left right left 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1. SÉlection de tension 70/100 v du systÈme - un interrupteur. Sélecteur permettant de choisir entre 70 v et 100 v pour un système de distribution audio haute tension. Ce réglage affectera ...
Page 40
40 7. Sortie de contrÔleur central - une mini-prise jack de 3,5 mm. Branchez sur n’importe quel appareil à régulation de tension, qui sera réglé sur on/off (marche/arrêt) en fonction de l’état on/off (marche/arrêt) de l’appareil 0e-ia1250. Lorsqu’une zone de l’0e-ia1250 est activée, la sortie du con...
Page 41: Télécommande Ir
41 télécommande ir la télécommande ir 0e-ia1250 commande les zones individuelles de l’0e-ia1250. Vous pouvez aussi vous en servir pour apprendre les commandes ir à une télécommande ir intégrée et programmable, à un système de contrôle de zone ou à un autre appareil d’acheminement ir. Toutes les zone...
Page 42: Installation
42 installation 1u rack vent above 0e-ia1250 1u rack vent below 0e-ia1250 1. L’0e-ia1250 est refroidi par convection. Ceci dépend du débit d’air libre naturel qui passe par les perforations de la plaque inférieure, par les ailettes de dissipation thermique interne, puis par le panneau supérieur pour...
Page 43: Infrastructure De Câblage
43 infrastructure de câblage câble pour haut-parleur l’0e-ia1250 est un amplificateur multi-canaux flexible présentant de nombreuses applications différentes. L’application d’un système donné, voire différentes configurations d’amplis pour différentes zones sur un système simple, peu(ven)t générer d...
Page 44: Raccordements
44 raccordements raccordement des haut-parleurs l’0e-ia1250 a trois modes d’amplificateurs pour les raccordements de haut-parleurs d’une zone. Avec passerelle 8 ohms, 4/8 ohms, 4/8 stéréo et 70 v/100 v. N’importe quelle combinaison de modes d’amplificateurs est autorisée dans les différentes zones.....
Page 45: Raccordements
45 raccordements 70 v/100 v cette configuration crée une zone de haut-parleur stéréo de 70 v. (30 w/canal) un système de 70 v/100 v utilise des haut-parleurs munis de prises spéciales, qui règlent le volume/la puissance électrique de chaque haut-parleur. Les systèmes de haut-parleurs de 70 v/100 v s...
Page 46: Raccordements
46 raccordements branchements audio zone line in (entrÉe de ligne de zone) ces branchements sont l’entrée d’une source audio au niveau de la ligne pour une zone dédiée. Si plusieurs sources audio au niveau de la ligne sont nécessaires dans une seule zone, utilisez un interrupteur audio sur l’entrÉe ...
Page 47: Connexions Du Contrôleur
47 connexions du contrôleur zone ir in (entrÉe ir de zone) ce raccordement permet la commande ir de la zone connectée pour l’alimentation, le volume, le mode muet, le bus/la ligne, etc. De la zone via les commandes de la télécommande ir 0e-ia1250 et un système de commande ir connecté. Ir receiver ir...
Page 48: Raccordements
48 zone mute (mode muet de la zone) ce raccordement permet la régulation de tension du mode muet de la zone. La tension appliquée (+3 à +30 vcc à 1 ma) mettra la sortie du haut-parleur de zone en mode muet. Lorsque la tension est coupée, la sortie du haut-parleur de zone est rétablie. 1. Mute/gnd (m...
Page 49: Raccordements
49 master control in (entrÉe du contrÔleur central) ce raccordement permet la régulation de tension des fonctions on/off (marche/arrêt) de 0e-ia1250. La tension appliquée (+3 à +30 vcc à 1 ma) met l’ampli sous tension. Lorsque la tension est coupée, l’ampli se met hors tension. (À l’arrêt, pas en ve...
Page 50: Réglages
50 cette section couvre l’ensemble des réglages à effectuer pour assurer le bon fonctionnement de l’appareil 0e- ia1250. Sortie de haut-parleur puissant de 70 v/100 v définit l’ensemble des raccordements de haut-parleurs de zones configurés sur 70 v ou 100 v. Cet interrupteur est utilisé conjointeme...
Page 51: Réglages
51 remote bypass (contournement À distance) le commutateur remote bypass (contournement à distance) permet/empêche la commande ir et rs232 par zone. Lorsque le commutateur est sur on (marche) (contourner la zone), la zone ne répond pas aux commandes ir ou rs232. Lorsque le commutateur est sur off (a...
Page 52
52 l r in out 1 2 3 4 5 6 zone 1 ir receiver zone in ceiling speakers zone 2 zone in ceiling speakers zone 3 zone in ceiling speakers zone 4 zone in ceiling speakers zone 5 zone in ceiling speakers zone 6 zone in ceiling speakers 0e-ia1250 audio distribution amp a/v receiver or other audio source sw...
Page 53: Fonctionnement
53 le mode de contrôle de 0e-ia1250 dépend de son mode d’utilisation. Trois modes de base sont expliqués : régulation de tension, ir contrôlé et rs232 contrôlé. Il existe bien sûr des variations de ces trois modes de commande de base, qui peuvent utiliser certaines options des autres modes. Consulte...
Page 54: Fonctionnement
54 1. On/off (marche/arrÊt) - appuyez sur le bouton power (alimentation) de la télécommande ir 0e-ia1250 pour activer la zone. Appuyez de nouveau sur ce bouton pour désactiver la zone. 2. Bus/line (bus/ligne) - appuyez sur le bouton bus pour sélectionner la source connectée à l’entrée de bus audio 0...
Page 55: Commandes Rs232
55 commandes 0e-ia1250 rs232 nom commande remarques zone power (alimentation de la zone) !{z#} pr{0/1}+ activation zone 2 : !2pr1+ désactivation zone 1 : !1pr0+ zone power toggle (activation/désactivation de l’alimentation de la zone) !{z#} pt+ zone volume (volume de la zone) !{z#} vo{v#}+ zone vol....
Page 56: Commandes Rs232
56 commandes 0e-ia1250 rs232 nom commande remarques treble decrement (décrément d’aigus) !{z#} td+ bass (graves) !{z#} bs{bt#}+ bass increment (incrément de graves) !{z#} bi+ bass decrement (décrément de graves) !{z#} bd+ balance !{z#} ba{b#}+ balance step left (blalance gauche) !{z#} bl+ balance le...
Page 57: Requêtes Rs232
57 requêtes rs232 requÊtes 0e-ia1250 rs232 nom requÊte rÉponse exemple rÉponse explication zone volume (volume de la zone) ?{z#}vo+ ?{z#}vo{v#}+ ?4vo49+ la zone 4 est actuellement réglée sur un volume sonore de 49. Channel volume (volume de canal) ?{c#}ch+ ?{c#}ch{v#}+ ?4vo49+ le canal 4 est actuell...
Page 58: Requêtes Rs232
58 requêtes rs232 zone activity (activité de zone) et zone status (État de zone) za – commande d’activation de mise à jour auto de l’activité de zone. Format - !Za{0/1}+ zs – requête d’état de la zone. Format - ?(z#}zs+ commande d’activation de mise à jour auto de l’activité de zone la mise à jour d...
Page 59: Réglages Rs232
59 réglages rs232 rÉglage du volume sonore 0e-ia1250 rÉglage 0e-ia1250 niveau d’attÉnuation 38 0 37 -1,25 36 -2,50 35 -3,75 34 -5,00 33 -6,25 32 -7,50 31 -8,75 30 -10,00 29 -11,25 28 -12,50 27 -13,75 26 -15,00 25 -16,25 24 -17,50 23 -18,75 22 -20,00 21 -21,25 20 -22,50 19 -23,75 18 -25,00 17 -27,50 ...
Page 60: Réglages Rs232
60 réglages rs232 rÉglages du niveau de graves/aigus 0e-ia1250 rÉglage 0e-ia1250 niveau (+/-db) 14 +14 13 +12 12 +10 11 +8 10 +6 9 +4 8 +2 7 0 6 -2 5 -4 4 -6 3 -8 2 -10 1 -12 0 -14 rÉglages de la balance gauche/droite 0e-ia1250 rÉglage 0e-ia1250 haut- parleur de gauche +/- ddb haut-parleur de droite...
Page 61: Spécifications
61 spécifications sections audio alimentation de sortie continue ................................................ 30 w par canal, 8 ohms à 1 khz thd 0,1 % 50 w par canal, 4 ohms à 1 khz thd 0,1 % 100 w avec passerelle, 8 ohms à 1 khz thd 0,1 % 30 w par canal, 70 v/100 v à 1 khz thd 0,1 % distorsion ...
Page 62: Garantie Limitée
62 1. Garantie limitée a. Généralités sous réserve des modalités de la présente garantie limitée, à compter de la date de vente et pendant la période de garantie applicable aux catégories de produits précisée au paragraphe 1b), adi garantit que ses produits w box technologies sont libres de tout vic...
Page 63: Garantie Limitée
63 détecteurs de mouvement infrarouge 84 mois attaches pour câbles À vie limitée câbles analogiques À vie limitée câbles de raccordement À vie limitée bornes de bus À vie limitée connecteurs b À vie limitée cordes d’extension À vie limitée contacts magnétiques À vie limitée bloc modulaire, câbles et...
Page 64: Garantie Limitée
64 3. Limitation de la responsabilité envers les clients de l’acheteur. L’acheteur s’engage à limiter la responsabilité envers ses clients dans la pleine mesure permise par la loi. L’acheteur reconnaît qu’adi ne sera réputée avoir fourni aux consommateurs de ses produits que les garanties qui sont e...
Page 65: Remarques
65 remarques.
Page 66: Remarques
66 remarques.
Page 67: Remarques
67 remarques.
Page 68
0e-ia1250