- DL manuals
- Magnetic Autocontrol
- Gate Opener
- MHTM MicroDrive
- Operating Instructions Manual
Magnetic Autocontrol MHTM MicroDrive Operating Instructions Manual
Summary of MHTM MicroDrive
Page 1
Operating instructions barrier mhtm tm microdrive doc-id: 5815,5001en version: 02.7.
Page 2
2 5815,5001en / version 02.7 translation of the original operating instructions magnetic autocontrol gmbh grienmatt 20 79650 schopfheim germany tel.: +49 (0)7622 695 5 fax.: +49 (0)7622 695 602 e-mail: info@ac-magnetic.Com internet: www.Ac-magnetic.Com.
Page 3: Contents
Barrier mhtm tm microdrive contents 5815,5001en / version 02.7 3 contents 1 general....................................................................................9 1.1 information regarding the operating instructions ...........9 1.2 pictogram explanation ..........................................
Page 4
Barrier mhtm tm microdrive contents 4 5815,5001en / version 02.7 4.2 access pro h .............................................................. 31 4.2.1 dimensions and weight ............................... 31 4.2.2 electrical connection.................................... 32 4.2.3 operating condit...
Page 5
Barrier mhtm tm microdrive contents 5815,5001en / version 02.7 5 8.4.4 installing induction loops in bitumen, asphalt, or concrete......................................60 8.4.5 installing induction loops under interlocking stone paving..............................62 8.5 unpacking .....................
Page 6
Barrier mhtm tm microdrive contents 6 5815,5001en / version 02.7 10.4 symbols in the display .............................................. 104 10.4.1 control button functions............................. 104 10.4.2 current state of the barrier ........................ 105 10.4.3 current programme m...
Page 7
Barrier mhtm tm microdrive contents 5815,5001en / version 02.7 7 10.15 menu "detector 1 (a-b)" ............................................140 10.15.1 check the working frequency of the induction loops .....................................141 10.15.2 reconciling and setting the operating frequency o...
Page 8
Barrier mhtm tm microdrive contents 8 5815,5001en / version 02.7 15 decommissioning, disassembly and disposal............... 172 16 ec-declarations of conformity ........................................ 173 16.1 barrier, pedestrian traffic impossible......................... 173 16.2 barrier, pedest...
Page 9: 1 General
Barrier mhtm tm microdrive general 5815,5001en / version 02.7 9 1 general 1.1 information regarding the operating instructions these operating instructions provide crucial information on handling of magnetic barriers mhtm tm microdrive. Pre-requisite for safe working is the observance of all specifi...
Page 10: Danger!
Barrier mhtm tm microdrive general 10 5815,5001en / version 02.7 1.2 pictogram explanation warning notes warning notes are characterised by pictograms in these operating instructions. The warning notes are followed by signal words expressing the scale of the hazard. It is absolutely essential to obs...
Page 11
Barrier mhtm tm microdrive general 5815,5001en / version 02.7 11 1.3 limitation of liability all specifications and notes in these operating instructions were compiled with consideration to the valid standards and regulations, the state of the art as well as to our long-standing knowledge and experi...
Page 12
Barrier mhtm tm microdrive general 12 5815,5001en / version 02.7 1.5 scope of delivery the scope of delivery comprises: 1 barrier housing incl. Drive unit and control 1 barrier 2 attachment profiles 2 prohibition sign stickers edge protection options if applicable supplied documentation per barrier:...
Page 13: Notice!
Barrier mhtm tm microdrive general 5815,5001en / version 02.7 13 1.9 ec-declarations of conformity ec-declarations of conformity (pursuant to ec machinery directive 2006/42/ec, annex ii) refer to page 173. 1.10 environmental protection notice! Notice! Danger for the environment by improper disposal ...
Page 14: 2 Safety
Barrier mhtm tm microdrive safety 14 5815,5001en / version 02.7 2 safety 2.1 intended use of the barriers the magnetic mhtm tm microdrive barriers are exclusively intended for controlling access to and exit of certain road vehicles in or from certain areas. The barrier is either controlled by a pers...
Page 15: Warning!
Barrier mhtm tm microdrive safety 5815,5001en / version 02.7 15 2.1.3 barrier, pedestrian traffic not impossible in vehicle barriers where personal traffic cannot be excluded and use by pedestrian traffic is intended. If persons and animals may be present, only the following barriers may be used in ...
Page 16
Barrier mhtm tm microdrive safety 16 5815,5001en / version 02.7 2.2 operator's responsibility the operator must comply with the statutory obligations regarding work safety. In addition to the work safety notes in these operating instructions, the safety, accident prevention and environmental provisi...
Page 17: Warning!
Barrier mhtm tm microdrive safety 5815,5001en / version 02.7 17 2.4 specialists and operating personnel 2.4.1 requirements warning! Warning! Risk of injury in case of inadequate qualification! Improper handling can lead to considerable bodily injuries and property damage. Therefore: – have any activ...
Page 18: Danger!
Barrier mhtm tm microdrive safety 18 5815,5001en / version 02.7 2.5 personal protective equipment it is necessary to wear personal protective equipment when dealing with the barrier so as to minimise health hazards. Before carrying out any work, properly dress in the necessary protective equipment s...
Page 19: Caution!
Barrier mhtm tm microdrive safety 5815,5001en / version 02.7 19 hot surfaces caution! Caution! Danger of burns! … indicates the presence of a hot surface. Non- observance of the safety instructions can lead to minor injuries. This pictogram is fixed on the following component: – motor in the barrier...
Page 20: Danger!
Barrier mhtm tm microdrive safety 20 5815,5001en / version 02.7 electric voltage – missing safety installations danger! Danger! Mortal danger by electric voltage! The safety installations that are required according to regional and local regulations must be provided by the customer. Usually these ar...
Page 21: Warning!
Barrier mhtm tm microdrive safety 5815,5001en / version 02.7 21 improper operation warning! Warning! Danger from improper operation of the barrier! Improper operation of the barrier can cause severe or lethal injuries! Therefore: – the barrier closes automatically in certain programme modes. Passing...
Page 22: Warning!
Barrier mhtm tm microdrive safety 22 5815,5001en / version 02.7 entering the danger area of the barrier – pedestrian traffic impossible warning! Warning! Danger from entering the danger area! The magnetic mhtm tm microdrive barriers are intended exclusively for closing off passages for motor vehicle...
Page 23: Warning!
Barrier mhtm tm microdrive safety 5815,5001en / version 02.7 23 improper transport warning! Warning! Danger from improper transport of the barrier boom and housing! The weight of the barrier boom or housing can severely injure a person! Therefore: – have them transported by specialists only. – use l...
Page 24: Warning!
Barrier mhtm tm microdrive safety 24 5815,5001en / version 02.7 insufficient fixing warning! Warning! Risk of injury at insufficient fixing! Insufficient fixing of individual components such as barrier housing, barrier boom and additions permitted by the manufacturer can cause severe injury! Therefo...
Page 25: Caution!
Barrier mhtm tm microdrive safety 5815,5001en / version 02.7 25 illegible signage caution! Caution! Risk of injury by illegible symbols! Labels and signs can become dirty or unrecognisable in the course of time. Therefore: – always keep safety, warning and operating notes in a well readable conditio...
Page 26: Warning!
Barrier mhtm tm microdrive safety 26 5815,5001en / version 02.7 2.7 danger area danger of crushing and shearing, barrier boom warning! Warning! Danger of crushing and shearing if the safety distance between the barrier boom and other objects is too low! A closing or opening barrier boom can cause se...
Page 27: 3 Identification
Barrier mhtm tm microdrive identification 5815,5001en / version 02.7 27 3 identification 3.1 type plate the type plate is provided inside at the barrier housing, next to the hood attachment. 5 8 3 4 7 2 1 q s-nr. Made in germany 10 mag00281 11 magnetic autocontrol gmbh d-79650 schopfheim 6 9 12 fig....
Page 28
Barrier mhtm tm microdrive identification 28 5815,5001en / version 02.7 3.2 type code – r a 0 3 0 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 position description 1 – 12 product group: access magnetic.Acess access-l magnetic.Access long access pro magnetic.Access pro access pro-l magnetic...
Page 29: 4 Technical
Barrier mhtm tm microdrive technical data 5815,5001en / version 02.7 29 4 technical data 4.1 access 4.1.1 dimensions and weight mag00109c a b 1 varioboom 2 1 3500 / 5000 / 6000 55 360 925 915 875 675 min. 800 245 315 97 min. 500 100 min. 500 fig. 3: dimensions barrier system and barrier boom profile...
Page 30
Barrier mhtm tm microdrive technical data 30 5815,5001en / version 02.7 designation unit access access pro access select l l l lane width mm 3500 5000 3500 6000 3500 6000 barrier housing (width x depth x height) mm see page 29, fig. 3. (315 x 360 x 915) barrier housing weight kg 40 table 2: dimensio...
Page 31
Barrier mhtm tm microdrive technical data 5815,5001en / version 02.7 31 4.2 access pro h 4.2.1 dimensions and weight mag00202a a b microboom 2 1 1 360 245 315 97 55 100 3500 / 4500 / 5000 / 6000 925 111 5 875 min. 800 min. 500 min. 500 fig. 4: dimensions barrier system and barrier boom profile – "ac...
Page 32
Barrier mhtm tm microdrive technical data 32 5815,5001en / version 02.7 designation unit access pro h 3.5 m 4.5 m 5.0 m 6.0 m lane width mm 3500 4500 5000 6000 barrier housing (width x depth x height) mm see page 35, fig. 4. (315 x 360 x 1115) barrier housing weight kg 44 table 6: dimensions and wei...
Page 33
Barrier mhtm tm microdrive technical data 5815,5001en / version 02.7 33 4.3 parking 4.3.1 dimensions and weight mag00198a a b 1 varioboom 2 1 3500 55 360 925 915 875 675 min. 800 245 315 97 min. 500 100 min. 500 fig. 5: dimensions barrier system and barrier boom profile – "parking" series 1 object s...
Page 34
Barrier mhtm tm microdrive technical data 34 5815,5001en / version 02.7 designation unit parking parking pro parking select lane width mm 3500 3500 3500 barrier housing (width x depth x height) mm see page 33, fig. 5. (315 x 360 x 915) barrier housing weight kg 40 table 10: dimensions and weight – "...
Page 35
Barrier mhtm tm microdrive technical data 5815,5001en / version 02.7 35 4.4 toll 4.4.1 dimensions and weight microboom-t mag00108b 2 1 a b 1 3000 min. 800 75 min. 500 255 910 360 315 111 5 875 97 min. 500 fig. 6: dimensions barrier system and barrier boom profile – "toll" series 1 object such as wal...
Page 36
Barrier mhtm tm microdrive technical data 36 5815,5001en / version 02.7 designation unit toll toll pro lane width mm 3000 barrier housing (width x depth x height) mm see page 35, fig. 6. (315 x 360 x 1115) barrier housing weight kg 42 table 14: dimensions and weight – "toll" series 4.4.2 electrical ...
Page 37
Barrier mhtm tm microdrive technical data 5815,5001en / version 02.7 37 4.5 control unit designation unit mgc (magnetic gate controller) supply voltage v dc 24 current consumption ─ max. 1 a max. 300 ma + current consumption of the different plug-in modules power consumption ─ max 24 w. Max. 7.2 w +...
Page 38
Barrier mhtm tm microdrive technical data 38 5815,5001en / version 02.7 4.6 plug-in module "detector a–b" designation unit plug-in module "detector a–b" current consumption ma 50 number of loop detectors ─ 2 (a and b) inductance range h 70 to 500 number of induction loop sensitivity levels ─ 10 leve...
Page 39: 5 Design and Function
Barrier mhtm tm microdrive design and function 5815,5001en / version 02.7 39 5 design and function 5.1 design 5.1.1 access and parking mag00199 2 1 5 6 3 4 fig. 7: barrier system design series "access" and series "parking" 1 barrier housing 2 varioboom (barrier boom) 3 pendulum support from 3.5 m ba...
Page 40
Barrier mhtm tm microdrive design and function 40 5815,5001en / version 02.7 5.1.2 access pro h mag00203 2 1 5 6 3 4 fig. 8: design barrier series "access pro h" 1 barrier housing 2 microboom (barrier boom) 3 pendulum support from 3.5 m barrier boom length (accessory) 4 nesting post (accessory) 5 em...
Page 41
Barrier mhtm tm microdrive design and function 5815,5001en / version 02.7 41 5.1.3 toll mag00200 2 3 4 1 fig. 9: design barrier system series "toll" 1 barrier housing 2 microboom-t (barrier boom) 3 empty conduits for mains cable, control lines and induction loop 4 concrete foundation with reinforcem...
Page 42
Barrier mhtm tm microdrive design and function 42 5815,5001en / version 02.7 5.2 function the barrier consists of a barrier housing with drive system and a barrier boom. The drive system consists of an electric motor, control unit, and the lever system. The lever system locks the barrier boom in bot...
Page 43: 6 Transport and Storage
Barrier mhtm tm microdrive transport and storage 5815,5001en / version 02.7 43 6 transport and storage 6.1 safety notes for transport improper transport warning! Warning! Danger from improper transport of the barrier boom and housing! The weight of the barrier boom or housing can severely injure a p...
Page 44: Notice!
Barrier mhtm tm microdrive transport and storage 44 5815,5001en / version 02.7 improper transport notice! Notice! The barrier system can be damaged by improper transport! Substantial material damages can result from improper transport. Therefore: – have all transport work performed by trained person...
Page 45
Barrier mhtm tm microdrive transport and storage 5815,5001en / version 02.7 45 6.3 transport barrier housing and barrier boom are delivered separately. The lifting gear must be designed for the weight of the barrier housing and barrier boom. For transport barrier modules refer to the safety notes on...
Page 46
Barrier mhtm tm microdrive design notes for induction loops 46 5815,5001en / version 02.7 7 design notes for induction loops for assembly and inspection, see page 58, chapter 8.4. Please observe following points when dimensioning the induction loops: induction loops respond only to metal. The mass i...
Page 47
Barrier mhtm tm microdrive design notes for induction loops 5815,5001en / version 02.7 47 arrangement passenger car loops – passage with long opening loop mag00074 1 2 3 fig. 11: passenger car loops – passage with long opening time 1 safety loop 2 opening loop 3 barrier due to a long opening loop ve...
Page 48
Barrier mhtm tm microdrive design notes for induction loops 48 5815,5001en / version 02.7 arrangement of lorry/ passenger car loops mag00076 2 3 4 1 ca. 1.00 m ca. 1.50 m ca. 1.00 m 1.00 m ca. 1.00 m ca. 1.50 m ca. 1.00 m 1.00 m fig. 13: lorry/passenger car loops 1 safety loop lorry (inductance "l1"...
Page 49
Barrier mhtm tm microdrive design notes for induction loops 5815,5001en / version 02.7 49 arrangement of passenger car and motorcycle loops mag00077 1 2 3 6 4 5 1.00 m 1.00 m 0.50 m 2.00 m 0.50 m fig. 14: passenger car and motorcycle loops 1 safety loop passenger car 2 opening loop passenger car 3 s...
Page 50: 8 Assembly
Barrier mhtm tm microdrive assembly and installation 50 5815,5001en / version 02.7 8 assembly and installation 8.1 safety see also safety notes on page 18, chapter 2.6 "occupational safety and special dangers". General warning! Warning! Danger by inappropriate installation! Inappropriate installatio...
Page 51
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 51 personal protective equipment the following must be worn during all assembly and installation work: work clothes protective gloves safety shoes protective helmet. 8.2 required steps the following steps are to be compl...
Page 52
Barrier mhtm tm microdrive assembly and installation 52 5815,5001en / version 02.7 8.3 foundation and empty conduits 50 2 mag00227a 1 3 5 4 1 7 6 min. 800 300 min. 500 min. 800 100 600 min. 500 fig. 15: assembly boom system 1 object like wall, building, etc. Keep a safety distance of at least 500 mm...
Page 53
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 53 8.3.1 foundation and empty conduits for the barrier assembly site the assembly site must meet the following requirements: the barrier must not be put up where there is a danger of flooding. Keep a safety distance of a...
Page 54
Barrier mhtm tm microdrive assembly and installation 54 5815,5001en / version 02.7 laying the foundation, installing empty conduits 600 450 500 180 160 160 135 180 135 a a 1 2 3 4 5 mag00155 min. 800 6 7 fig. 16: foundation plan 1 foundation anchor (4 pcs.) 2 optional when using loop connection; emp...
Page 55
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 55 6. Create flat line in the base area. The following requirements must be fulfilled: level and horizontal. Surface deviation: max. 1 mm/m² 7. Let concrete cure. 8. Apply moisture protection agent to concrete surface. N...
Page 56: Caution!
Barrier mhtm tm microdrive assembly and installation 56 5815,5001en / version 02.7 8.3.2 foundation and empty conduits for nesting post or light barrier post danger of crushing caution! Caution! Crushing danger between the fork at the nesting post and the barrier boom! Fingers and hands can be crush...
Page 57
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 57 foundation the foundation must meet the following requirements: see page 52, fig. 15 and page 57, fig. 18. Have sufficient load-carrying capacity. (concrete foundations: c35/45 xd3 xf2) water cement value: 0.5 foundat...
Page 58
Barrier mhtm tm microdrive assembly and installation 58 5815,5001en / version 02.7 8.4 assembly and installation of induction loops depending on the application safety installations must be installed on site. Induction loops, light barriers, etc. Can be used as safety installations. The safety insta...
Page 59
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 59 please observe following points when installing the induction loop: loop geometry and clearances install the loop symmetrically to the barrier boom. Please make sure that the barrier boom is attached to the side of th...
Page 60
Barrier mhtm tm microdrive assembly and installation 60 5815,5001en / version 02.7 8.4.2 induction loops the induction loops are available as ready assembled cables in various lengths (type kas 1 to 5) from magnetic. Alternatively a loop can be manufactured from single wire. The following requiremen...
Page 61
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 61 2. Lay the loop carefully into the groove and push it down by means of a blunt object, such as a piece of wood. The insulation must by no means be damaged. 3. To avoid slipping of the loop, fix the loop using small wo...
Page 62
Barrier mhtm tm microdrive assembly and installation 62 5815,5001en / version 02.7 8.4.5 installing induction loops under interlocking stone paving s0105a 3 1 2 4 5 300 150 30 fig. 23: installing an induction loop under interlocking stone paving 1 barrier housing 2 paving 3 loop cable 4 sand bed 5 s...
Page 63
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 63 8.5 unpacking the individual packages are packed according to the expected transport conditions. Only environment-friendly materials have been used for the packaging. The packaging should protect the individual compon...
Page 64
Barrier mhtm tm microdrive assembly and installation 64 5815,5001en / version 02.7 8 1 2 5 6 7 4 3 9 mag00205 fig. 24: assemble housing 1 barrier housing 2 nut 3 spring washer 4 disc d8,4 5 disc d13 6 mounting profile 7 foundation anchor 8 foundation 9 silicon sealant assemble housing 1. The foundat...
Page 65
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 65 8.7 assemble nesting post or light barrier post the nesting post and the light barrier post are attached with 4 foundation anchors each. You can order a mounting set consisting of foundation anchor, washers, spring ri...
Page 66
Barrier mhtm tm microdrive assembly and installation 66 5815,5001en / version 02.7 8.8 assemble safety light barrier only magnetic safety light barriers must be used. 8.8.1 assemble transmitter a b b mag00224 a 4 3 1 2 1 c 160 17 280 292 Ø 13 Ø 6 Ø 6 15 30 100 440 ~ 160 30 17 Ø 13 280 292 15 70 Ø 6 ...
Page 67
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 67 8.8.2 assemble receiver 309 160 309 160 30 30 x x x x x mag00225 3 4 5 3 a b 1 1 2 c fig. 26: assemble the receiver's light barrier housing on the post a light barrier post b nesting post c light barrier housing 1 gap...
Page 68: Warning!
Barrier mhtm tm microdrive assembly and installation 68 5815,5001en / version 02.7 8.9 assemble barrier boom type "varioboom" the barrier boom type "varioboom" is delivered in two parts install short barrier boom profile with assembled connection plates, half-shells and end-caps. Long barrier boom p...
Page 69: Caution!
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 69 the edge protection is included in the delivery loosely in 2 m pieces. If the barrier was ordered with the light strips option, the barrier boom is delivered with the mounted edge protection. The number of edge protec...
Page 70
Barrier mhtm tm microdrive assembly and installation 70 5815,5001en / version 02.7 warning! Danger of crushing between barrier boom and barrier housing! 4. Switch off power supply. Ensure that the system is powered down. Secure against reactivation. The balancing springs in the lever system are rela...
Page 71
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 71 8. Install end-cap to the barrier boom. Mag00172a fig. 30: install end-cap 9. Push barrier boom with pre-assembled flange onto the flange shaft. Mag00175 fig. 31: assemble flange with barrier boom 10. Align barrier bo...
Page 72
Barrier mhtm tm microdrive assembly and installation 72 5815,5001en / version 02.7 13. Push the barrier into the top-most position. The clamping lever must be at the stop for the "open" position. If required, push straight through the upper tool bore with a tool to press the lever arm from the dead ...
Page 73
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 73 5. Install the flange on the flange plates with the 2 hexagon socket screws 8 af. Make sure: tighten the screws evenly with a tightening torque of 60 nm. That the air gap between flange and flange plate must be consis...
Page 74
Barrier mhtm tm microdrive assembly and installation 74 5815,5001en / version 02.7 9. Push the barrier into the top-most position. The clamping lever must be at the stop for the "open" position. If required, push straight through the upper tool bore with a tool to press the lever arm from the dead p...
Page 75: Caution!
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 75 8.12 conversion "left version" – "right version" (varioboom and microboom) danger of injury caution! Caution! Danger of injury! There is a danger of injury when mounting the barrier boom. Therefore: – barrier booms as...
Page 76
Barrier mhtm tm microdrive assembly and installation 76 5815,5001en / version 02.7 7. Remove the flange with the barrier boom. Mag00175 fig. 34: disassemble flange with barrier boom 8. Remove the v-ring from the flange shaft. Mag00174 fig. 35: remove the v-ring 9. Slightly loosen the two hexagon soc...
Page 77
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 77 10. Unhook the balancing springs in the lever system. For this, press a tool straight through the upper tool bore. The lever arm is pressed from the upper dead point see page 165, chapter 13.5. 11. Remove the flange s...
Page 78: Warning!
Barrier mhtm tm microdrive assembly and installation 78 5815,5001en / version 02.7 26. Switch the "service" switch on the control unit the led lights red. The display backlighting flashes. See page 119, chapter 10.7.7 mode "service". 27. Close the barrier with the middle right button at the control ...
Page 79
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 79 mag00169 1 2 3 fig. 37: balancing springs in the lever system. 1 barrier boom 2 balancing spring 3 screw with locknuts 8.13.1 setting balancing springs check and adjust balancing springs check balancing springs with t...
Page 80
Barrier mhtm tm microdrive assembly and installation 80 5815,5001en / version 02.7 adjust balancing springs: 5. Remove the barrier housing hood. 6. Remove the rear barrier housing door. 7. Adjust springs with a wrench via the screws with locknuts. Barrier boom angle > 30°: this balancing springs are...
Page 81
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 81 8.13.2 overview table balancing springs note! The following overview tables "balancing springs" do not take into consideration any attachment parts. For barrier booms with attachment parts, the required number of spri...
Page 82
Barrier mhtm tm microdrive assembly and installation 82 5815,5001en / version 02.7 the following overview tables apply for barriers with microboom. Overview table balancing springs for barriers with microboom and without pendulum support lane width number springs weak number springs strong 1.5 to 2....
Page 83: Warning!
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 83 the following overview table applies for barriers with microboom-t. Overview table balancing springs for barriers with microboom-t and without pendulum support lane width number springs weak number springs strong 1.5…...
Page 84: Caution!
Barrier mhtm tm microdrive assembly and installation 84 5815,5001en / version 02.7 8.15 set nesting post height danger of crushing caution! Caution! Crushing danger between the fork at the nesting post and the barrier boom! Fingers and hands can be crushed when the barrier boom runs into the nesting...
Page 85
Barrier mhtm tm microdrive assembly and installation 5815,5001en / version 02.7 85 8.16 stick on prohibition signs the delivery includes two prohibition signs as stickers. Attach the prohibition signs to the barrier boom according to the following drawing. Mag05014 fig. 40: apply prohibition signs, ...
Page 86: 9 Electrical
Barrier mhtm tm microdrive electrical connection 86 5815,5001en / version 02.7 9 electrical connection 9.1 safety see also safety notes on page 18, chapter 2.6 "occupational safety and special dangers". Electric voltage danger! Danger! Mortal danger by electric voltage! Touching live parts can be le...
Page 87: Caution!
Barrier mhtm tm microdrive electrical connection 5815,5001en / version 02.7 87 hot surfaces caution! Caution! Danger of burns! The motor surface may be hot. Touching this hot surface can lead to burns. Therefore: – do not touch these hot surfaces. – after switching off the power supply wait some min...
Page 88: Danger!
Barrier mhtm tm microdrive electrical connection 88 5815,5001en / version 02.7 9.3 connecting the power cable electric voltage danger! Danger! Mortal danger by electric shock! If the mains supply is not connected to the terminal clamps correctly, loosens from the connection clamps and touches the ho...
Page 89
Barrier mhtm tm microdrive electrical connection 5815,5001en / version 02.7 89 mains supply placement 3. Connect the mains supply with the intended terminal clamps x1: l / n / pe) in the barrier housing according to the following figures also refer to page 177, chapter 17.1 "wiring diagram". Place m...
Page 90
Barrier mhtm tm microdrive electrical connection 90 5815,5001en / version 02.7 9.4 connect customer's control lines (signalling devices) the following connections are available for control and feedback on customer’s side: 8 digital inputs for controlling the barrier. 4 digital outputs to feed back i...
Page 91
Barrier mhtm tm microdrive electrical connection 5815,5001en / version 02.7 91 9.4.1 connecting safety devices as safety devices, you must connect safety loops or safety light barriers to the control unit. Safety loops must only be connected to monitor vehicles. Only magnetic safety light barriers m...
Page 92
Barrier mhtm tm microdrive electrical connection 92 5815,5001en / version 02.7 9.4.3 connecting safety loop the safety loop is connected to the plug-in module "detector1 (a-b)", clamps a or clamps b. See page 177, chapter 17.1 "wiring diagrams". The clamp function parameters can be set in the menu "...
Page 93
Barrier mhtm tm microdrive electrical connection 5815,5001en / version 02.7 93 9.4.4 connect and test the safety light barriers connecting safety light barrier connect the transmitter and receiver connection lines of the safety light barriers to clamps x11 and x20. By default, magnetic installs a ju...
Page 94: Warning!
Barrier mhtm tm microdrive electrical connection 94 5815,5001en / version 02.7 check safety light barrier function perform function test by holding an object into the light path between the transmitter and receiver. The following items must be met: the yellow led at the receiver must go out. The bar...
Page 95
Barrier mhtm tm microdrive electrical connection 5815,5001en / version 02.7 95 factory setting clamp description function in1 input 1 open low priority in2 input 2 open low priority in3 input 3 opening with vend count in4 input 4 open high priority in5 input 5 external opening loop exit in6 input 6 ...
Page 96
Barrier mhtm tm microdrive electrical connection 96 5815,5001en / version 02.7 function description external opening loop exit 1) the barrier opens when +24 v dc are applied to this input. Connect external opening loops to this input. External impact detection you can install external impact detecti...
Page 97
Barrier mhtm tm microdrive electrical connection 5815,5001en / version 02.7 97 factory setting clamp description function do1 digital output 1 boom locking do2 digital output 2 pulse after passage do3 digital output 3 signal light a do4 digital output 4 signal light b no1 relay 1 open no2 relay 2 cl...
Page 98
Barrier mhtm tm microdrive electrical connection 98 5815,5001en / version 02.7 function description parallel operation this output can be used to operate two barriers synchronously. This output function must be activated via the menu "master/slave". See page 133, chapter 10.10.11. For information on...
Page 99
Barrier mhtm tm microdrive electrical connection 5815,5001en / version 02.7 99 function description direction 1 pls b => a 1) the vehicle drives from direction b to a. When the vehicle leaves loop b in the direction of loop a, this output emits a counter impulse of 300 ms. A b do no/nc t = 300 ms ma...
Page 100
Barrier mhtm tm microdrive electrical connection 100 5815,5001en / version 02.7 function description direction 1 a => b 1) the vehicle drives from direction a to b. When the vehicle leaves loop a, this output starts emitting a permanent signal. When the vehicle leaves loop b, this output stops the p...
Page 101
Barrier mhtm tm microdrive electrical connection 5815,5001en / version 02.7 101 function description direction 2 b => a 1) the vehicle drives from direction b to a. When the vehicle enters loop a, this output starts emitting a continuous signal. When the vehicle leaves loop a, this output stops the ...
Page 102: Warning!
Barrier mhtm tm microdrive parameterising control unit 102 5815,5001en / version 02.7 10 parameterising control unit 10.1 safety see also safety notes on page 18, chapter 2.6 "occupational safety and special dangers". Improper parameterisation warning! Warning! Risk of injury by improper parameteris...
Page 103
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 103 10.3 displays on the control unit example "operational view" mag00126a a b d c access select 4 4 5 6 1 2 3 fig. 48: example "operational view" 1 programme mode, here programme mode 4 2 barrier type, here type "acce...
Page 104
Barrier mhtm tm microdrive parameterising control unit 104 5815,5001en / version 02.7 10.4 symbols in the display 10.4.1 control button functions the control unit is equipped with 4 control buttons. The function of the control buttons change depending on the current view in the display. The current ...
Page 105
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 105 10.4.2 current state of the barrier the barrier can have the following states: symbols description barrier boom closed. Barrier boom open. Barrier boom opens. Closing signal was recognised. Traffic lights active. B...
Page 106
Barrier mhtm tm microdrive parameterising control unit 106 5815,5001en / version 02.7 10.4.3 current programme mode symbols description current programme mode, here programme mode 4 for description of programme modes, refer to page 109, chapter 10.7. Programme mode "service" for description of progr...
Page 107
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 107 10.5 parameterising options menu setup, refer to page 185. Programme modes overview, refer to page 109. Example: select programme mode 1. The operating view is displayed. See page 103, fig. 48. 2. Press right contr...
Page 108
Barrier mhtm tm microdrive parameterising control unit 108 5815,5001en / version 02.7 10.6 parameterising values example: change hold-open time 1. The operating view is displayed. See page 103, fig. 48. 2. Press right control button . 3. The "main menu" menu is displayed. 4. Select the menu "setup" ...
Page 109
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 109 10.7 select programme mode 8 programme modes and the service mode are available for the mhtm tm microdrive barriers. Programme modes 1 to 4 are manual modes. In the manual modes, the barrier must be closed manually...
Page 110
Barrier mhtm tm microdrive parameterising control unit 110 5815,5001en / version 02.7 10.7.1 mode 1: maintained contact typical application this mode is suitable, e.G. For parallel operation of two barriers. See page 133, chapter 10.10.11 "master/slave". Function the barrier is controlled only by on...
Page 111
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 111 10.7.2 mode 2: deadman typical application this mode is suitable for barriers on parking places, factory premises, etc. The barrier must be operated by a person. Function the barrier is operated by two buttons. For...
Page 112
Barrier mhtm tm microdrive parameterising control unit 112 5815,5001en / version 02.7 10.7.3 mode 3: pulse control (bistable) typical application this mode is suitable for barriers on factory premises, etc. That are little frequented by vehicles. The signal generator may be, e.G. A wireless button. ...
Page 113
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 113 10.7.4 mode 4: two-pulse control typical application this mode is suitable for barriers on factory premises, etc. That are often frequented by vehicles. The barrier must be operated by a person. Function the barrie...
Page 114
Barrier mhtm tm microdrive parameterising control unit 114 5815,5001en / version 02.7 10.7.5 automatic modes 5 to 8: drive direction 1 – overview and differences the automatic modes differ in their functions in drive direction 1 "safety loop opening loop". In drive direction 2 "opening loop safety l...
Page 115
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 115 mode 5: automatic (5) typical application this mode is suitable for the automatic operation of a barrier, e.G. With card readers, remote control, coin acceptors and induction loops or light barriers. Passage of the...
Page 116
Barrier mhtm tm microdrive parameterising control unit 116 5815,5001en / version 02.7 the barrier closes in the following cases: if the vehicle drives over both loops in direction 1 "safety loop opening loop", the barrier closes as soon as the vehicle leaves the safety loop. The opening loop here do...
Page 117
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 117 function from direction 1 "safety loop opening loop", the barrier is opened by an opening signal at one of the digital opening inputs. Hold-open time is not active in this mode. The barrier closes in the following ...
Page 118: Warning!
Barrier mhtm tm microdrive parameterising control unit 118 5815,5001en / version 02.7 10.7.6 automatic modes 5 to 8: drive direction 2 in drive direction 2 "opening loop safety loop", the automatic modes are identical. Closing barrier boom – maximum distance of the induction loops warning! Warning! ...
Page 119
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 119 10.7.7 mode "service" in the "service" mode, all opening and closing signals are ignored. The functions of safety devices like the safety loop or safety light barrier remain active for security reasons. This means ...
Page 120
Barrier mhtm tm microdrive parameterising control unit 120 5815,5001en / version 02.7 10.8 menu "information" ( ) call and navigate 1. The operating view is displayed. See page 103, fig. 48. 2. Press left control button . 3. Use the left control button to scroll within the menu. 4. The "information"...
Page 121
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 121 10.10 menu "setup" 10.10.1 barrier speed operating view main menu settings barrier speed parameters description closing select the closing speed for the barrier boom. The closing speed can be changed for all barrie...
Page 122
Barrier mhtm tm microdrive parameterising control unit 122 5815,5001en / version 02.7 operating view main menu setup delays parameters description close delay the barrier only closes if the set time for the closing delay is over. The timer for closing delay is started with the closing signal. With t...
Page 123
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 123 10.10.3 cut off angle operating view main menu setup cut off angle parameters description safety loop close this parameter serves to ensure that a closed barrier can not be opened without authorisation. Where the b...
Page 124
Barrier mhtm tm microdrive parameterising control unit 124 5815,5001en / version 02.7 10.10.6 vend count operating view main menu setup vend count parameters description reset behaviour use this parameter to set vend count reset behaviour. The function "vend count" is available for programme modes 4...
Page 125
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 125 drive direction 1: "safety loop opening loop" mag00096 1 2 3 4 5 fig. 53: programme mode 5 with vend count, passage in direction 1 1 remote control, card reader, coin acceptor, etc. 2 barrier 3 opening loop exit 4 ...
Page 126
Barrier mhtm tm microdrive parameterising control unit 126 5815,5001en / version 02.7 drive direction 2: "opening loop safety loop" mag00097 1 2 3 4 5 fig. 54: programme mode 5 with impulse storage, passage in direction 2 1 remote control, card reader, coin acceptor, etc. 2 barrier 3 opening loop ex...
Page 127
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 127 10.10.7 impact settings operating view main menu setup impact settings parameters description impact response select the barrier boom's impact reaction if the control unit detects an impact. Also see page 123, chap...
Page 128
Barrier mhtm tm microdrive parameterising control unit 128 5815,5001en / version 02.7 10.10.8 start-up behaviour use this menu to select the start-up behaviour of the barrier according to the following events: after switching on voltage supply after return of voltage after reset you can select betwe...
Page 129
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 129 operating view main menu settings start-up behaviour option description 2 reference run in this option, the barrier initially performs a reference run. This means that the barrier opens completely at low speed. Rel...
Page 130
Barrier mhtm tm microdrive parameterising control unit 130 5815,5001en / version 02.7 operating view main menu settings start-up behaviour option description 4 reference run in this option, the barrier boom stops initially. The barrier will only carry out a reference run after a release signal. Rele...
Page 131
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 131 operating view main menu settings start-up behaviour option description 6 reference run in this option, the barrier boom stops initially. Release signal the barrier carries out a reference run after the left operat...
Page 132
Barrier mhtm tm microdrive parameterising control unit 132 5815,5001en / version 02.7 10.10.9 power failure operating view main menu settings power failure parameters description power failure this parameter sets whether the barrier boom opens at power outage or opens or closes depending on the barr...
Page 133
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 133 10.10.10 closure by light barrier operating view main menu settings closure by light barrier parameters description closure by light barrier use this parameter to select the closing behaviour for barriers with only...
Page 134
Barrier mhtm tm microdrive parameterising control unit 134 5815,5001en / version 02.7 10.10.12 menu "language" operating view main menu setup language parameters description language select menu language options german english french spanish italian portuguese table 52: menu "language" 10.11 menu "a...
Page 135
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 135 operating view main menu attachments signal light parameters description signal mode a (continued) warning signal (connection of a visual or acoustic signal/ permanent signal before and during closing of the barrie...
Page 136
Barrier mhtm tm microdrive parameterising control unit 136 5815,5001en / version 02.7 operating view main menu attachments signal light parameters description signal mode c select function for output "signal light c". Options traffic light (permanent signal for red/green signal lights): barrier clos...
Page 137
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 137 10.11.2 boom contact settings the barrier can optionally be equipped with a boom contact in the flange. In the "toll" series, the boom contact is integrated by default and performed as a "swing away" or "auto swing...
Page 138
Barrier mhtm tm microdrive parameterising control unit 138 5815,5001en / version 02.7 operating view main menu attachments boom contact settings parameters description closing delay the parameters are only relevant in the following cases: the barrier is a "swing away" or "auto swing away" design. In...
Page 139
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 139 10.12 menu "service" this menu is only intended for magnetic's service and only accessible with a password. 10.13 menu "information" operating view main menu information parameters description serial no. Displays t...
Page 140
Barrier mhtm tm microdrive parameterising control unit 140 5815,5001en / version 02.7 10.15 menu "detector 1 (a-b)" this menu is used to reference the induction loops a and b. Operating view main menu detector 1 (a-b) parameters description recalibration start reference of the induction loops (activ...
Page 141
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 141 operating view main menu detector 1 (a-b) frequency settings parameters description freq. A displays the currently measured frequency for induction loop a freq. B displays the currently measured frequency for induc...
Page 142
Barrier mhtm tm microdrive parameterising control unit 142 5815,5001en / version 02.7 10.15.2 reconciling and setting the operating frequency of the induction loop operating frequency requirements the operating frequency must fulfil following requirements: when driving over the induction loop with a...
Page 143
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 143 frequency value of the un- assigned induction loop unstable if the frequency value of an induction loop is unstable, this induction loop is influenced by an induction loop of another barrier or an external detector...
Page 144
Barrier mhtm tm microdrive parameterising control unit 144 5815,5001en / version 02.7 10.16 menu "detector 2 (c-d)" this menu is displayed if a second plug-in module with the function "detector" was plugged into the control unit. This menu is used to reference the induction loops c and d. The menu "...
Page 145
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 145 set hand transmitter code the hand transmitter code is set via dip switches in the hand transmitter. We recommend changing the dip switches' standard settings. 1. Open hand transmitter housing. For this, press the ...
Page 146
Barrier mhtm tm microdrive parameterising control unit 146 5815,5001en / version 02.7 delete remote control 1. The operating view is displayed. See page 103, fig. 48. 2. Press right operating button . 3. The "main menu" menu is displayed. 4. Select the menu "radio control" with the two middle button...
Page 147
Barrier mhtm tm microdrive parameterising control unit 5815,5001en / version 02.7 147 10.18 factory settings reset parameters this menu can be used to reset the parameters to factory settings. 1. The operating view is displayed. See page 103, fig. 48 2. Press right operating button . 3. The "main me...
Page 148: 11 Start-Up and Operation
Barrier mhtm tm microdrive start-up and operation 148 5815,5001en / version 02.7 11 start-up and operation 11.1 safety see also safety notes on page 18, chapter 2.6 "occupational safety and special dangers". General warning! Warning! Danger by inappropriate start-up and operation! Inappropriate star...
Page 149: Notice!
Barrier mhtm tm microdrive start-up and operation 5815,5001en / version 02.7 149 11.2 commissioning check before to initial start-up the following inspections must be performed prior to initial start-up: check electrical connections. Check barrier boom position. Check balancing springs in the lever ...
Page 150: Warning!
Barrier mhtm tm microdrive start-up and operation 150 5815,5001en / version 02.7 switching on 1. Remove the barrier housing hood. 2. Remove the barrier housing door. 3. Switch on the barrier via the 2-pole mains switch. 4. Depending on the settings in the "start-up behaviour" menu, the barrier boom ...
Page 151
Barrier mhtm tm microdrive start-up and operation 5815,5001en / version 02.7 151 if the barrier is put out of operation for a longer period, proceed as follows: 1. Switch off barrier. See page 149, chapter 11.3. 2. Remove the barrier boom if necessary. See page 167, chapter 14.3. 3. Protect the barr...
Page 152: 12 Maintenance
Barrier mhtm tm microdrive maintenance 152 5815,5001en / version 02.7 12 maintenance 12.1 safety see also safety notes on page 18, chapter 2.6 "occupational safety and special dangers". General warning! Warning! Danger by inappropriate maintenance! Inappropriate maintenance can cause severe or letha...
Page 153: Notice!
Barrier mhtm tm microdrive maintenance 5815,5001en / version 02.7 153 12.2 cleaning the cleaning interval essentially depends on the environmental conditions and the climate. Aggressive cleaning aids and substances notice! Notice! Unit damage possible! Aggressive detergents and consumables may damag...
Page 154
Barrier mhtm tm microdrive maintenance 154 5815,5001en / version 02.7 12.3 maintenance schedule the following describes the maintenance work that is necessary for optimal, trouble-free operation. Maintenance intervals must be observed. If increased wear of individual components or functional groups ...
Page 155
Barrier mhtm tm microdrive maintenance 5815,5001en / version 02.7 155 interval maintenance work to be carried out by check the barrier's mechanics. Check the spring setting of the lever system. Check barrier boom position. Visual inspection of the induction loops and the carriageway for damage. Chec...
Page 156: 13 Malfunctions
Barrier mhtm tm microdrive malfunctions 156 5815,5001en / version 02.7 13 malfunctions this chapter describes possible causes of malfunctions and trouble shooting tasks. Contact your dealer in case of malfunctions that cannot be repaired by means of the following information. Procure spare parts fro...
Page 157: Warning!
Barrier mhtm tm microdrive malfunctions 5815,5001en / version 02.7 157 danger of injury after lightning strike warning! Warning! Danger of injury from total outage or barrier malfunction after lightning has hit the barrier! If the barrier is struck by lightning, this may lead to total outage or malf...
Page 158
Barrier mhtm tm microdrive malfunctions 158 5815,5001en / version 02.7 malfunction possible cause corrective action to be carried out by barrier does not open completely. Spring tension in the balancing springs of the lever system set too weakly for the barrier boom weight. Adjust balancing springs....
Page 159
Barrier mhtm tm microdrive malfunctions 5815,5001en / version 02.7 159 malfunction possible cause corrective action to be carried out by barrier does not close. The message "waiting for authorization" appears on the display. The message appears after the voltage supply is switched on, after voltage ...
Page 160
Barrier mhtm tm microdrive malfunctions 160 5815,5001en / version 02.7 13.3 warning and interference messages on the display the control unit display indicates the corresponding warning or error message in case of an error. Warning messages warning messages serve as notice. The barrier continues to ...
Page 161
Barrier mhtm tm microdrive malfunctions 5815,5001en / version 02.7 161 number designation possible cause corrective action ff05 warning book contact / swing-sway active at the "boom contact" input, boom ejection was detected. Barrier with swingaway and automatic return: wait for delay. Barrier with ...
Page 162
Barrier mhtm tm microdrive malfunctions 162 5815,5001en / version 02.7 number designation possible cause corrective action 8130 warning heartbeat error communication with a plug module was interrupted. Check if all plugged modules are listed in the main menu. Perform reset. See page 164, chapter 13....
Page 163
Barrier mhtm tm microdrive malfunctions 5815,5001en / version 02.7 163 number designation possible cause corrective action ff30 warning impact detection impact was recognised. Check safety devices. Adjust menu "cut off angle". See page 123, chapter 10.10.3. If there was no impact on an obstacle/vehi...
Page 164: Notice!
Barrier mhtm tm microdrive malfunctions 164 5815,5001en / version 02.7 13.3.4 warning and interference messages – all modules number designation possible cause corrective action 6010 warning watchdog reset sw error contact service if required. 8110 warning bus fault warning contact service if requir...
Page 165
Barrier mhtm tm microdrive malfunctions 5815,5001en / version 02.7 165 13.5 closing or opening the barrier boom in case of power failure in case of power failure, the barrier boom may be in the lower or upper dead point. I.E. The barrier boom can no longer be easily moved manually. In this case, pro...
Page 166: 14 Repair
Barrier mhtm tm microdrive repair 166 5815,5001en / version 02.7 14 repair 14.1 safety see also safety notes on page 18, chapter 2.6 "occupational safety and special dangers". General warning! Warning! Danger by inappropriate repair! Inappropriate repair can cause severe or lethal injuries. Therefor...
Page 167: Warning!
Barrier mhtm tm microdrive repair 5815,5001en / version 02.7 167 14.2 spare parts warning! Warning! Risk of injury by incorrect spare parts! Incorrect or defective spare parts can result in damage, malfunctions or total failure and also impair safety. Therefore: – use only the manufacturer's origina...
Page 168
Barrier mhtm tm microdrive repair 168 5815,5001en / version 02.7 1. Secure barrier danger area e.G. With barrier tape. 2. Remove the barrier housing hood. 3. Remove the barrier housing door. Warning! Danger of crushing between barrier boom and barrier housing! 4. Switch off power supply. Ensure that...
Page 169
Barrier mhtm tm microdrive repair 5815,5001en / version 02.7 169 10. Remove end-cap from the barrier boom. Mag00170 fig. 61: disassemble end-cap. 11. Slide a slot nut into the groove at the underside of the barrier boom. Place a slot nut on the upper side of the barrier boom. Mag00171 fig. 62: assem...
Page 170
Barrier mhtm tm microdrive repair 170 5815,5001en / version 02.7 13. Install end-cap to the barrier boom. Mag00172a fig. 64: install end-cap 14. Push barrier boom with pre-assembled flange onto the flange shaft. 15. Align barrier boom vertically. 16. Install the flange on the flange shaft using the ...
Page 171
Barrier mhtm tm microdrive repair 5815,5001en / version 02.7 171 14.3.2 barrier boom type "microboom-t" 1. Secure barrier danger area e.G. With barrier tape. 2. Remove the barrier housing hood. 3. Remove the barrier housing door. Warning! Danger of crushing between barrier boom and barrier housing! ...
Page 172
Barrier mhtm tm microdrive decommissioning, disassembly and disposal 172 5815,5001en / version 02.7 11. Switch on power supply. 12. Switch the "service" switch on the control unit the led lights red. The display backlighting flashes. See page 119, chapter 10.7.7 mode "service". 13. Close the barrier...
Page 173
Barrier mhtm tm microdrive ec-declarations of conformity 5815,5001en / version 02.7 173 16 ec-declarations of conformity 16.1 barrier, pedestrian traffic impossible find the ec compliance statement for barriers where pedestrian traffic can be excluded, in the following. See also page 14, chapter 2.1...
Page 174: Ec-Declaration of Conformity
Barrier mhtm tm microdrive ec-declarations of conformity 174 5815,5001en / version 02.7 ec-declaration of conformity der hersteller/ manufacturer magnetic autocontrol gmbh grienmatt 20 – 28 telefon +49 (0) 7622 / 695-5 d-79650 schopfheim telefax +49 (0) 7622 / 695-602 dokumentationsbevollmächtigter/...
Page 175
Barrier mhtm tm microdrive ec-declarations of conformity 5815,5001en / version 02.7 175 16.2 barrier, pedestrian traffic not impossible find the ec compliance statement for barriers where pedestrian traffic cannot be excluded, in the following. See also page 15, chapter 2.1.3..
Page 176: Ec-Declaration of Conformity
Barrier mhtm tm microdrive ec-declarations of conformity 176 5815,5001en / version 02.7 ec-declaration of conformity der hersteller/ manufacturer magnetic autocontrol gmbh grienmatt 20 – 28 telefon +49 (0) 7622 / 695-5 d-79650 schopfheim telefax +49 (0) 7622 / 695-602 dokumentationsbevollmächtigter/...
Page 177: 17 Appendix
Barrier mhtm tm microdrive appendix 5815,5001en / version 02.7 177 17 appendix 17.1 wiring diagram following wiring diagrams apply to standard barriers. Observe the customer specific wire diagrams for customer specific barriers if applicable..
Page 178
Barrier mhtm tm microdrive appendix 178 5815,5001en / version 02.7.
Page 179
P a g e of m ic ro d ri v e 5 5 2 6 ,0 0 1 0 mhtm 0 2 5 k 1 0 5 6 5 + 4 2 = 1 2 3 4 5 6 7 8 9 3 m a in s co n n e ct io n p o w e r su p p ly u n it 0 1 0 6 0 8 .1 1 .1 1 5 k 1 1 5 6 0 g p 0 2 .1 2 .2 0 1 0 fmeier d a te n a m e m o d if ic a ti o n p ro je ct version 8 5 - 2 6 4 v a c 5 0 /6 0 h z ...
Page 181
P a g e of m ic ro d ri v e 5 5 2 6 ,0 0 1 0 mhtm 0 2 5 k 1 0 5 6 5 + 4 3 = 1 2 3 4 5 6 7 8 9 4 b a rr ie r co n tr o lle r m g c in p u t/ o u tp u t 0 2 0 6 0 8 .1 1 .1 1 5 k 1 1 5 6 0 g p 0 2 .1 2 .2 0 1 0 fmeier d a te n a m e m o d if ic a ti o n p ro je ct version gn pk wh br gr ye r e r e v o...
Page 183
P a g e of m ic ro d ri v e 5 5 2 6 ,0 0 1 0 mhtm 0 2 5 k 1 0 5 6 5 + 4 4 = 1 2 3 4 5 6 7 8 9 sa fe ty -l ig h t b a rr ie rs o p ti o n 0 3 0 6 0 8 .1 1 .1 1 5 k 1 1 5 6 0 g p 0 2 .1 2 .2 0 1 0 fmeier d a te n a m e m o d if ic a ti o n p ro je ct version bn bl w h (n .C .) bk transmitter bk n.C. B...
Page 185
Barrier mhtm tm microdrive appendix 5815,5001en / version 02.7 185 17.2 menu setup mag00256a a b d c access select 4 1) service information motor gw detector 1 (a-b) radio control main menu prog. Mode setup attachments ethernet factory settings detector 2 (c-d) 2) 3) warnings inputs detector 1 (a-b)...
Page 186
Barrier mhtm tm microdrive appendix 186 5815,5001en / version 02.7 mag00130f master/slave 2) service information motor gw detector 1 (a-b) detector (c-d) cut off angle inputs outputs vend count impact settings main menu prog. Mode attachments barrier speed delays open close hold-open time closing de...
Page 187
Barrier mhtm tm microdrive appendix 5815,5001en / version 02.7 187 mag00131d 2) software # service information motor gw detector 1 (a-b) factory settings prog. Mode setup temperature hardware version software version serial no. Signal light signal mode a signal mode b lead time start event boom rele...
Page 188
Barrier mhtm tm microdrive appendix 188 5815,5001en / version 02.7 mag0021 1b 2) radio control delete remote control teach in remote control information number of transmitter with remote control without remote control freq. A freq. B freq. Shift ref. A ref. B sensitivity b frequency settings informa...
Page 189: Index
Barrier mhtm tm microdrive index 5815,5001en / version 02.7 189 index a assemble housing ..............................................63 assembly housing...........................................................63 safety light barrier...........................................66 assembly and insta...
Page 190
Barrier mhtm tm microdrive index 190 5815,5001en / version 02.7 m maintained contact........................................... 110 maintenance .................................................... 152 maintenance schedule..................................... 154 malfunction table.......................
Page 191
Barrier mhtm tm microdrive 5815,5001en / version 02.7 191.
Page 192
F05471553 magnetic autocontrol gmbh grienmatt 20 79650 schopfheim germany tel.: +49 (0)76 22 695 5 fax: +49 (0)76 22 695 602 e-mail: info@ac-magnetic.Com internet: www.Ac-magnetic.Com address sales partner:.