User manual valid for attaxx models: 2.5 rgb - 3.1. Rgb - 3.7 rgb - 4.9 rgb - 5 rgb - 6+ rgb - 8 rgb - 10 rgb - 12 rgb - 14 rgb - 15 rgb - 18 rgb abstract the new attaxx multicolor projector series is a highly professional, state of the art laser show device, which eliminates the need of water cooli...
2 as the first company in the world, medialas announced an rgb whitelight projector late 2002, and presented the design early 2003 on frankfurt´s pro light & sound trade show. In the meantime, medialas sold and manufactured a large number of multicolor systems and earned lots of experience in design...
3 preparations remove the screws of the front lid. Lift the lid and unplug the earth connector on the left power supply section of the attaxx. Be sure to work in a dust-free ambient, so the optical section is not contaminated. Now safely store the top cover and avoid touching the output window. Duri...
4 cleaning the optical surfaces some of the optical surfaces in your attaxx system are made for very high reflectivity, such as mirror surfaces etc. Reflectivity of more than 98% is obtained only, if the mirror surface is free of dirt or fingerprints. Also, lenses and filters depend on a clean surfa...
5 db25 male connector: 1: x input + 2: y input + 5: red + 6: green + 7: blue + 14: x input - 15: y input - 18: red – 19: green – 20: blue - 25: ground all signals are available also on the db25 female connector, for wiring the control signals to a second projector. Adjusting projection size just nex...
6 we hereby confirm that the following devices attaxx full color laser systems comply with the essential safety requirements, laid down in the regulations of the committee to assimilate the provisions of law of all participating eu states on the electromagnetic compatibility (2004/108/eg). The devic...
7 highspeed-galvo-driver microamp tuning and adjustment introduction the microamp is currently the smallest and fastest scanamp for cti´s 6800 or 6210s on the world market. It´s new technology allows to scan up to 60k with selected galvanometers, at a reduced scanangle of 4° optical. But even at lar...
8 the ilda standard driver is set too fast or output speed of computer is too slow. The inner circle is larger than the green square. Driver and output speed matches together. Driver is too slow or output speed of computer is too high. Readjust driver or slow down computer. Adjustments standard conf...
9 inverting of axis by using the jumpers at the inputs, each driver can be inverted easily. This can be done during scanning also. Just pull out the jumpers and put them in at 90° rotated. Heatsinking the microamps are relatively insensitive to heat, since the power stage contains a overheat shutdow...
10 important hints do not remove the driver board from its mounting bracket. This additional metal plate is needed for ground and increases stability of the driver. The bracket is isolated from ground. Do not use cheap and unshielded cable. We recommend to use the microamps only with medialas cables...
11 information netport lan option netport enhances any laser projector to full lan connectivity. Drive your laser projector from standard lan line, by using cat5 cable. No more analog ilda signal cables are required. Additionally, netport offers internal memory for storing lasershow or laser animati...
12 dmx-player function netport comes with a standalone player for ilda files. The player allows playback of show sequences stored on internal sd-card by control via dmx or directly from the webinterface. Shows or sequences must be stored in ilda-format (format 0, 1, 2, 4 or 5). Configuration of the ...
13 frame repeat the number of repetitions of each frame of the sequence during playback. By using this parameter, the speed of the animation can be controlled. Frame repeat can also be controlled via dmx. Displaymode this is the playback mode of each sequence. A sequence can be run in loop mode or i...
14 dmx settings select 'dmx settings' in the 'player' menu. You will see the actual dmx channel settings. To control the player via dmx signals, the function of the various dmx channels must be set. Dmx base address this is the base address of dmx where all used channels of netport are staring from....
15 size (x) und size (y) size control for both projection axes x and y individual. The difference to 'size' is that 255 is the maximum, 115-140 is minimum (10%) and values below 115 are inverting the display of the axis. This can be used to invert orientation of the projected image. Offset (x) und o...
