N-Com B3 User Instructions And Safety - page 4

Summary of B3

  • Page 1

    En b3 b3 - 18/01/2016 14:21:00 user instructions and safety congratulations on your purchase of an n-com product. N-com b3 was made using the most advanced technologies and the best materials. Long-running tests and thorough system development have allowed the highest audio quality to be achieved. F...

  • Page 3

    Contents 1. Warnings and safety .................................................................................................4 1.1.Road safety ............................................................................................................................................................

  • Page 4

    En 4 1. Warnings and safety read this user manual carefully, as well as the user manuals for other n-com kits that you will be using with the n-com b3. Read the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. Caution: the product cannot be used in offi...

  • Page 5

    B3 5 1.4. Appropriate use use the device only in the normal position, as described in the product documentation. Do not attempt to disassemble, tamper with or modify any part of the n-com system. Caution: adjust the volume of the n-com system (where provided) and of the audio sources connected to it...

  • Page 6

    En 6 1.7. Disposal refer to this user manual and to manuals related to other parts of the n-com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: the presence of a crossed-out wheelie bin indicates...

  • Page 7

    B3 7 3. Installation you can download the installation video from www.N-com.It n-com / download section. Fig. 1 fig. 2 fig. 3  remove the “n-com” protection plate located on the helmet shell (fig. 1) and open the helmet chin guard (flip up helmets).  remove the right and left cheek pads from the h...

  • Page 8

    En 8 fig. 7 only for full-face helmets  remove the chin guard by pulling on the special red tab. Fig. 8  remove the right and left polystyrene cheek pads by gently pulling them out of the helmet. The helmet shell can be opened slightly to facilitate the removal of the cheek pad. Caution: in case t...

  • Page 9

    B3 9 3.1. Installing the microphone jet helmets or flip-up helmets fig. 9 fig. 10 fig. 11 fig. 12  prepare the microphone by inserting the microphone clamp, being careful to position it properly (fig. 9) note: the flat part of the clamp must be facing upward when the microphone is positioned as sho...

  • Page 10

    En 10 3.2. Installing the system on the helmet fig. 15  position the system inside the helmet as shown in figure 15, next to the n-com housing in the shell. Fig. 16  looking at the helmet from the outside, slide the rear positioning tab into groove a as shown in the figure;  press in the area mar...

  • Page 11

    B3 11  insert the microphone connector in the micro usb electronic plate.  before you place the speaker in its housing, apply the velcro pad to the polystyrene cheek pad (fig. 19). Fig. 18 fig. 19 fig. 20  position the loudspeaker in the special housing obtained in the polystyrene cheek pad (fig....

  • Page 12

    En 12 fig. 22 only for jet helmets or flip-up helmets  secure the battery-holder support to the right side of the helmet, lining up the holes with the pins on the shell (fig. 22) fig. 23 only for full face helmets  position the battery in the right polystyrene cheek pad housing (fig. 23). Before y...

  • Page 13

    B3 13 fig. 25 fig. 26  position the comfort padding in its housing (see specific instructions provided in the helmet user manual), hooking the neck roll (fig. 25).  position both the comfort cheek pads in their housing (see specific instructions provided in the helmet user manual) making sure that...

  • Page 14

    En 14 5. Basic functions all n-com system functions are available through the operation of three pushbuttons: “ ”, “on” and “ ”. Every time the system is given a command, a special acoustic signal can be heard, which varies depending on the function being requested, or on the vocal command given. ...

  • Page 15

    B3 15 5.2. N-com wizard “n-com wizard” is the pc application that can be used to manage and configure the b3 system. The programme can be downloaded from the internet site www.N-com.It, in the “download” section. In order to use it, a helmet equipped with b3 must be connected to the pc, using the us...

  • Page 16

    En 16 note: the affiliation is stored in the helmet and in the cell phone and it is not lost when the two devices are turned off. As a result it needs to be carried out only once. Note: if a bluetooth device (mobile phone or gps) equipped with music player with bluetooth a2dp player has already been...

  • Page 17

    B3 17 8. Gps satellite navigator functions b3 is compatible with the most common satellite navigators for motorcycles. By connecting the n- com system to the gps, all instructions will be transferred to the helmet. Every time the navigator communicates instructions, the intercom via bluetooth with t...

  • Page 18

    En 18 10. Music via bluetooth you can listen to high quality music by connecting the n-com system to a device equipped with bluetooth a2dp (advanced audio distribution profile) protocol. The n-com system is also equipped with bluetooth avrcp (audio video remote control profile) protocol, which allow...

  • Page 19

    B3 19 12. N-com rider-passenger intercom mode in order for two n-com systems to communicate with one another, they have to be paired up first. 12.1. Intercom affiliation 1. Make sure both n-com bluetooth systems are turned off; 2. Set both n-com bluetooth systems in pairing up mode by pressing “on” ...

  • Page 20

    En 20 4. After a few seconds, the helmets “recognize” one another: a confirmation beep is given in helmet 2 that indicates the memory setting where helmet 1 is stored and intercom communication is established; n.B.: if all the memory settings are free, helmet 2 will store helmet 1 in position a (see...

  • Page 21

    B3 21 14. “universal intercom” the n-com b3 system can be connected via bluetooth to intercom systems of other brands, thanks to the universal intercom function. 14.1. Pairing up the universal intercom to pair up an n-com system and an intercom of another brand (from now on called intercom b), the f...

  • Page 22

    En 22 15. Battery before using the n-com device for the first time, recharge the battery completely for at least 10 hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times. Afterwards, you can recharge the battery for shorter peri...

  • Page 23

    B3 23 16. Summary table of controls button on on pressure brief long brief long brief long brief long turning on x (2s) turning off x (4s) increase volume x decrease volume x b a si c f u n c tio n s scroll menu (base, radio, bike to bike) x (2s) answer phone call x x x voice call x (4s) hang up/rej...

  • Page 24

    En 24 button on on pressure brief long brief long brief long brief long automatic search for new station x (2s) change station (pre-set stations) x (2s) r a d io m e n u pre-set station x (4s) answer call bike-to- bike x x x intercom swap (from bike-to-bike to rider-pillion passenger)* x x connectio...

  • Page 25

    B3 25 17. Limited warranty with this limited warranty certificate, nolangroup warrants this product to be free from defects in material and workmanship at the time of its original purchase by the buyer. We invite you to: - read the cautions pertaining to safety and proper use. - read the warranty te...

  • Page 26

    En 26 nolangroup shall not be responsible in case the product presents limited capabilities due to the operating mode of cell phones or of other accessories or equipment not supplied by nolangroup. Tampering with the internal electronic card or with other parts of the n-com system shall invalidate t...

  • Page 27

    B3 27 nolangroup reserves itself the right to modify, at any time and without advance notice, the product characteristics, functions, compatibility and software. Some countries do not allow the exclusion or limitation of incidental or consequential damages, or the limitation of the duration of impli...

  • Page 28

    18. Warranty registration form product name: b3 identification code buyer’s information name last name address phone e-mail dealer’s stamp date of purchase.