NAC Image Technology MEMRECAM GX-1 584032-2 Quick Reference Manual

Summary of MEMRECAM GX-1 584032-2

  • Page 1

    1 quick reference manual memrecam gx-1 october 5, 2007 nac image technology inc..

  • Page 2: Contents

    2 contents 1. Configuration overview ・ standard system ・ basic options ・ other options 2. I/o connectors 3. Led status indicators 4. Connections ・ single camera operation ・ multi-camera operation 5. Operations ・ basic operation schematics ・ gx link operations ・ j-pad 3 operations 6. Specifications a...

  • Page 3: 1. Configuration Overview

    3 1. Configuration overview 1.1 standard system memrecam gx-1, 2gb, color (584032-2) memrecam gx-1, 2gb, monochrome (584032-4) ・ 1 x digital high speed camera memrecam gx-1 ・ 1 x control software gx link ・ 1 x j1 i/o cable (for power input, trigger input, etc.) ・ 1 x j2 i/o cable (for viewfinder, j-...

  • Page 4

    4 1.3 other options multi-camera network options ・ gx hub (584030--) ・ remote cable 3m (h12061-3) ・ remote cable 7.5m (h12061-5) ・ remote cable 15m (h12061-7) ・ remote cable 25m (h12061-8) ・ remote cable 50m (h12061x0) ・ remote cable 75m (h12061x1) ・ remote cable 100m (h12061x2) gx hub hi-g options ...

  • Page 5: 2. I/o Connectors

    5 2. I/o connectors memrecam gx-1 has three i/o connectors at the back of the camera. Followings show locations and major usages of each i/o. Please refer to appendix b for details. J1: power ・ power input ・ trigger input (contact, ttl) ・ status signal outputs j2: vf j-pad ・ viewfinder ・ j-pad 3 ・ u...

  • Page 6: 3. Led Status Indicator

    6 3. Led status indicator memrecam gx-1 indicates its status using five led’s at the back of the camera. This section will explain features and functions of the led status indicators. Location and layout status 1) ub: usb led status green an usb device is connected. Off no connection or power off. 2...

  • Page 7

    7 3) cm: camera mode led status blue stop/ready mode: status just after boot up or completion of recording, or stop/still in playback. White view mode: the imager is outputting image signal while the last recording image data is kept in the memory. Magenta arm mode: the imager is outputting image si...

  • Page 8: 4. Connections

    8 4. Connections single camera operation host pc 1000base-t switching hub m em recam cat5e or cat6 cable max.100m gx1 ac adapter * you can connect the gx1 to a laptop pc directly using a cat5e/cat6 cable. Local single camera operation (w/o pc) m em recam gx1 viewfinder usb memory / usb card reader a...

  • Page 9

    9 multi-camera operation m em recam host pc 1000base-t switching hub gx-hub gx1 remote cable up to 100m up to 100m m em recam gx remote cable(copper) max.100m cat5e or cat6 cable max.100m gx1 m em recam gx-hub gx1 up to 100m m em recam gx1 gx-hub.

  • Page 10: 5. Operations

    10 5. Operations 5.1 basic operation procedures power on boot up ready view arm triggered recording done download playback auto view mode power off memory backup.

  • Page 11

    11 5.2 gx link (control s/w) operations refer to gx link manual for operations in detail. Click a camera button attach a camera (s) ready view arm triggered recording done download playback auto view mode boot up gx link gx link identifies all applicable cameras network settings at pc * ip address s...

  • Page 12

    12 5.3 j-pad 3 operations 1) general j-pad 3 is an optional remote controller useable for the memrecam gx series. It allows you to operate most of the functions of the camera without a control pc (gx link). Important: settings in gx link (control software) are prior to settings in the camera. Theref...

  • Page 13

    13 lock switch ・ settings can be locked by a slide switch at side of the j-pad to prevent mis-operation. 5) lcd spec: 128 x 64 dots, monochrome, backlight contents of display ・ status: mode, frame rate, frame size, shutter, trigger mode, id, scene, frame counter, time, payback range tool bar ・ recor...

  • Page 14

    14 6) appearance.

  • Page 15

    15 7) functions of keys a) setup keys menu enters menu for: ・ general setup ・ recording setup ・ system setup ends menu set sets the parameter up moves a cursor to upward down moves a cursor to downward left moves a cursor to left right moves a cursor to right b) mode keys stop stops playback. Stops ...

  • Page 16

    16 c) direct setting keys following keys allow you to set essential parameters and functions directly as regards recording, playback and data download. Frm rate set key: sets frame rate. Shutter set key: sets shutter speed. Trig set key: sets trigger position. S.Set set key: sets a start frame in pl...

  • Page 17

    17 d) combination key operations + jumps to the start frame in stop status. + jumps to the end frame in stop status. + + enters a maintenance menu setting for; ・ ntsc/pal ・ ip address ・ reset to default settings e) jog dial cw for upward, ccw for downward, push for set. Set cw ccw push.

  • Page 18

    18 6. Specifications • sensor: 12-bit, 1.3m-pixel cmos sensor • frame rate: 50-200,000pps • resolution: 1,280 x 1,024pixels up to 2,000pps 640 x 480pixels up to 6,000pps 512 x 384pixels at 10,000pps * see appendix a for more details • electronic shutter: open to 3µ sec. * see appendix a for more det...

  • Page 19

    19 -appendix a- frame rate, resolution, sensing area & exposure time frame rate (pps) resolution in largest or square format (pixels) sensing area (mm) max. Exposure (µ sec) min. Exposure (µ sec) setting step (µ sec) 100 1,280 x 1,024 27.78 x 22.22 9,996 6 1 or 2 250 1,280 x 1,024 27.78 x 22.22 3,99...

  • Page 20

    20 -appendix b- j1 1 dc 24v in 2 dc return 3 est in 4 est gnd 5 trigger signal in (make contact/ttl) 6 trigger signal gnd 7 arm status out 8 arm status gnd 9 fault status out 10 fault status gnd j2 1 arm command in 2 gnd (arm command return) 3 usb vbus 4 usb d+ 5 usb d- 6 usb gnd 7 nc 8 nc 9 dc 24v ...

  • Page 21

    21 j3 1 ethernet signal mdi 0+ 2 ethernet signal mdi 0- 3 ethernet signal mdi 1+ 4 ethernet signal mdi 1+ 5 ethernet signal mdi 2+ 6 ethernet signal mdi 2- 7 ethernet signal mdi 3+ 8 ethernet signal mdi 3- 9 est in 10 est gnd 11 irig signal in 12 irig signal gnd 13 trigger signal in a (photo coupler...

  • Page 22

    22 -appendix c- dimensional drawing.

  • Page 23

    23 mounting plate 6×φ6.4 172 2×3/8-16UNC φ4.3 36 50 38 1 0 0 7 8 8 80 80 1 0.