1. DL manuals
  2. NanoCam Plus
  3. Automobile Accessories
  4. NCP-MIRDVRHD2
  5. User Manual

NanoCam Plus NCP-MIRDVRHD2 User Manual

Manual is about: clip on mirror monitor with built-in dash cam dvr & rear camera

Summary of NCP-MIRDVRHD2

  • Page 1

    User manual clip on mirror monitor with built-in dash cam dvr & rear camera ncp-mirdvrhd2.

  • Page 2

    2 caution ................................................................................................................................................................................................4 battery warning ...................................................................................

  • Page 3

    3 3 photo mode ...................................................................................................................................................................................12 3.1 photo menu ...........................................................................................

  • Page 4

    4 caution • ensure you are using your mirror dvr within your countries’ road laws. Please make sure you are familiar with your local road legislation before use. • avoid leaving your mirror dvr in direct sunlight for extended periods of time in an unventilated space. • please set time and date befor...

  • Page 5

    5 1. Introduction thank you for purchasing a nanocam plus clip on mirror dvr with integrated 1080p dash cam dvr & 720p rear camera. We are certain that our product will give you trouble free operation while providing you with a safety feature that enhances your driving experience. Our products, like...

  • Page 6

    6 1.3 product overview 1. Usb/rear camera input 8. (m) button 2. Power input (12v, dc) 9. 5.0” ips lcd screen 3. Micro sd card slot 10. Heat dissipation / air flow 4. Power on/off button 11. Fastening clips 5. (up) button 12. Wide angle lens 6. (ok/rec) button 13. Speaker 7. (down) button 14. Reset ...

  • Page 7

    7 2.2.1 connecting the rear facing camera 1. Clean the inside of your rear window ensuring there is no dust on the window. 2. Remove the protective film from the rear facing camera’s 3m sticker and place the camera in the desired position on the inside of your rear window, ensuring that the rear cam...

  • Page 8

    8 2.3.2.2 power off if the mirror dvr is currently recording, please manually stop the recording by pressing the button. Press and hold the power button on the front of the mirror dvr. After powering off the device please wait for 10 seconds before powering the mirror dvr on again. 2.3.2.3 reset the...

  • Page 9

    4. Press to enter the date/time . 5. Use the and buttons to edit the selected digit and the button to confirm and progress to the next digit. 6. To save and exit the date and time menu, press the button note: 1. Menus cannot be accessed while the camera is recording. Please stop the recording before...

  • Page 10

    10 2.7 video menu when the mirror dvr is powered on the video screen will start by default. In this screen recording will automatically start and can be stopped by pressing the button. To access the menu, ensure that the mirror dvr is not recording then press and hold the button for 2 seconds. 2.7.1...

  • Page 11

    11 2.7.3 exposure exposure is used to manually control the light sensitivity settings. To change the exposure setting follow the instructions below. 1. Press the button to stop the mirror dvr from recording. 2. Press and hold the button for 2 seconds to enter the menu . 3. Use the and buttons to nav...

  • Page 12

    2.7.6 g sensor the g sensor defines the required force needed to trigger emergency recording. Once emergency recording is triggered the current recording will be saved and protected from being saved over by the normal loop recording. To set the required sensitivity please follow the instructions bel...

  • Page 13

    2. Press and hold the button for 2 seconds to enter the menu . 3. Use the and buttons to navigate the menu and highlight the image quality setting and press to select. 4. Use the and buttons to highlight your required image resolution, then press the button to confirm your selection. Note: 1. Menus ...

  • Page 14

    14 3.1.4 date stamp date stamp is used to stamp your photos with the date and time they were taken. To select your preferred date and time format follow the instructions below. 1. Press the button to stop the mirror dvr from recording. 2. Press and hold the button for 2 seconds to enter the menu . 3...

  • Page 15

    15 4. Use the and buttons to highlight your preferred language and the button to confirm your selection. Note: 1. Menus cannot be accessed while the camera is recording. Please stop the recording before attempting to access the menu. 3.2.3 format formatting the micro sd card will delete all informat...

  • Page 16

    16 3.3 playback screen this screen is used to playback photos and videos. To access the playback screen ensure that the camera is not recording and short press the button. This will send the camera to the photo screen . While in the photo screen , short press the button again which will bring you to...

  • Page 17

    17 4.0 menu options menu resolution full hd (1080p) hd (720p) image quality 1m 8m 2m 12m 5m loop recording 1 minute 5 minutes 3 minutes camera flip off on park mode off on park mode sensitivity high low medium g-sensor high low medium off volume high low medium off white balance automatic incandesce...

  • Page 19

    19 warranty terms & conditions our goods come with guarantees that cannot be excluded under the australian & new zealand consumer law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to ha...

  • Page 20

    Www.Nanocamplus.Com.Au www.Nanocamplus.Co.Nz © nanocam plus 2016.