NOVAK NITRO SERVO REGULATOR Manual

Allows usage of higher voltage receiver battery packs

 (6-8 

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs)

 and regulates output 

voltage to the radio system, to provide strong/consistent 

servo performance throughout the duration of your run. 

TO INSTALL SERVO BOOSTER:

1.  Connect the Servo Booster’s

RED 20 gauge silicone wire

 (larger 

wire  with  no  connectors)

to

Positive  (+)  of  the  receiver  battery

pack.

2. Connect the Servo Booster’s

BLACK 20 gauge silicone wire to

Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the

battery slot (or other unused channel) of the receiver.

The Servo Booster’s receiver harness is wired for new style receivers. If you have 

older style KO or older black cased Airtronics receivers, you may need to change 

the wiring sequence of the harness to avoid possible receiver damage.

4. Mount  the  Servo  Booster’s  main  module  to  the  vehicle’s

chassis using the included double-sided mounting tape.

5.  Mount the Servo Booster’s ON/OFF switch in a convenient place

in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power 

switch you will need to turn the radio system on and off.  

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from 

defects in materials or workmanship for a period of 120 days from the original date of 

purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed 

www.teamnovak.

#5460 Nitro Servo  

Regulator

 (w/B.E.C. Regulator)

IN-5460-1 • 10/2004

Allows usage of higher voltage receiver battery packs

 (6-8 

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs)

 and regulates output 

voltage to the radio system, to provide strong/consistent 

servo performance throughout the duration of your run. 

TO INSTALL SERVO BOOSTER:

1.  Connect the Servo Booster’s

RED 20 gauge silicone wire

 (larger 

wire  with  no  connectors)

to

Positive  (+)  of  the  receiver  battery

pack.

2. Connect the Servo Booster’s

BLACK 20 gauge silicone wire to

Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the

battery slot (or other unused channel) of the receiver.

The Servo Booster’s receiver harness is wired for new style receivers. If you have 

older style KO or older black cased Airtronics receivers, you may need to change 

the wiring sequence of the harness to avoid possible receiver damage.

4. Mount  the  Servo  Booster’s  main  module  to  the  vehicle’s

chassis using the included double-sided mounting tape.

5.  Mount the Servo Booster’s ON/OFF switch in a convenient place

in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power 

switch you will need to turn the radio system on and off.  

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from 

defects in materials or workmanship for a period of 120 days from the original date of 

purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed 

www.teamnovak.

#5460 Nitro Servo  

Regulator

 (w/B.E.C. Regulator)

IN-5460-1 • 10/2004

Allows usage of higher voltage receiver battery packs

 (6-8 

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs)

 and regulates output 

voltage to the radio system, to provide strong/consistent 

servo performance throughout the duration of your run. 

TO INSTALL SERVO BOOSTER:

1.  Connect the Servo Booster’s

RED 20 gauge silicone wire

 (larger 

wire  with  no  connectors)

to

Positive  (+)  of  the  receiver  battery

pack.

2. Connect the Servo Booster’s

BLACK 20 gauge silicone wire to

Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the

battery slot (or other unused channel) of the receiver.

The Servo Booster’s receiver harness is wired for new style receivers. If you have 

older style KO or older black cased Airtronics receivers, you may need to change 

the wiring sequence of the harness to avoid possible receiver damage.

4. Mount  the  Servo  Booster’s  main  module  to  the  vehicle’s

chassis using the included double-sided mounting tape.

5.  Mount the Servo Booster’s ON/OFF switch in a convenient place

in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power 

switch you will need to turn the radio system on and off.  

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from 

defects in materials or workmanship for a period of 120 days from the original date of 

purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed 

www.teamnovak.

#5460 Nitro Servo  

Regulator

 (w/B.E.C. Regulator)

IN-5460-1 • 10/2004

Allows usage of higher voltage receiver battery packs

 (6-8 

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs)

 and regulates output 

voltage to the radio system, to provide strong/consistent 

servo performance throughout the duration of your run. 

TO INSTALL SERVO BOOSTER:

1.  Connect the Servo Booster’s

RED 20 gauge silicone wire

 (larger 

wire  with  no  connectors)

to

Positive  (+)  of  the  receiver  battery

pack.

2. Connect the Servo Booster’s

BLACK 20 gauge silicone wire to

Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the

battery slot (or other unused channel) of the receiver.

The Servo Booster’s receiver harness is wired for new style receivers. If you have 

older style KO or older black cased Airtronics receivers, you may need to change 

the wiring sequence of the harness to avoid possible receiver damage.

4. Mount  the  Servo  Booster’s  main  module  to  the  vehicle’s

chassis using the included double-sided mounting tape.

5.  Mount the Servo Booster’s ON/OFF switch in a convenient place

in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power 

switch you will need to turn the radio system on and off.  

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from 

defects in materials or workmanship for a period of 120 days from the original date of 

purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed 

www.teamnovak.

#5460 Nitro Servo  

Regulator

 (w/B.E.C. Regulator)

IN-5460-1 • 10/2004

Allows usage of higher voltage receiver battery packs

 (6-8 

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs)

 and regulates output 

voltage to the radio system, to provide strong/consistent 

servo performance throughout the duration of your run. 

TO INSTALL SERVO BOOSTER:

1.  Connect the Servo Booster’s

RED 20 gauge silicone wire

 (larger 

wire  with  no  connectors)

to

Positive  (+)  of  the  receiver  battery

pack.

2. Connect the Servo Booster’s

BLACK 20 gauge silicone wire to

Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the

battery slot (or other unused channel) of the receiver.

The Servo Booster’s receiver harness is wired for new style receivers. If you have 

older style KO or older black cased Airtronics receivers, you may need to change 

the wiring sequence of the harness to avoid possible receiver damage.

4. Mount  the  Servo  Booster’s  main  module  to  the  vehicle’s

chassis using the included double-sided mounting tape.

5.  Mount the Servo Booster’s ON/OFF switch in a convenient place

in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power 

switch you will need to turn the radio system on and off.  

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from 

defects in materials or workmanship for a period of 120 days from the original date of 

purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed 

www.teamnovak.

#5460 Nitro Servo  

Regulator

 (w/B.E.C. Regulator)

IN-5460-1 • 10/2004

Allows usage of higher voltage receiver battery packs

 (6-8 

cell Ni-Cd or Ni-MH, or 2 cell Li-Po packs)

 and regulates output 

voltage to the radio system, to provide strong/consistent 

servo performance throughout the duration of your run. 

TO INSTALL SERVO BOOSTER:

1.  Connect the Servo Booster’s

RED 20 gauge silicone wire

 (larger 

wire  with  no  connectors)

to

Positive  (+)  of  the  receiver  battery

pack.

2. Connect the Servo Booster’s

BLACK 20 gauge silicone wire to

Negative (–) of the receiver battery pack.

3. Plug the Servo Booster’s black 3-pin receiver harness into the

battery slot (or other unused channel) of the receiver.

The Servo Booster’s receiver harness is wired for new style receivers. If you have 

older style KO or older black cased Airtronics receivers, you may need to change 

the wiring sequence of the harness to avoid possible receiver damage.

4. Mount  the  Servo  Booster’s  main  module  to  the  vehicle’s

chassis using the included double-sided mounting tape.

5.  Mount the Servo Booster’s ON/OFF switch in a convenient place

in the car using a screw or the included double-sided tape.

NOTE: The Servo Booster’s ON/OFF switch will be the only power 

switch you will need to turn the radio system on and off.  

PRODUCT WARRANTY: Novak Electronics, Inc. guarantees all products to be free from 

defects in materials or workmanship for a period of 120 days from the original date of 

purchase (verified by dated, itemized sales receipt). In no case shall our liability exceed 

www.teamnovak.

#5460 Nitro Servo  

Regulator

 (w/B.E.C. Regulator)

IN-5460-1 • 10/2004