Page 1 tested & listed by omni-test laboratories, inc report no.: 215-s-31-4 portland oregon, usa us c models dv8 (n,l) dv14 (n,l) dv21 (n,l) need help ? Do not return this product to the store where you purchased it. If you have questions about assembling or operating this appliance or if it seems ...
Page 2 heater .............................
Dv14 dv8 dv21 page 3 610 m 610 m dv8 dv8 dv8 dv8 dv14 dv14 dv14 dv14 dv21 dv21 dv21 dv21 the efficiency rating of the appliance is a product thermal efficiency rating determined under continuous operating conditions and was determined independently of any installed system. Or /ng /ng propane/ /ng /n...
Page 4 dv8 dv14 dv21 12 15/64” 19 39/64” 25 19/32” 5 1/32” (mdv8-mdv14) 7 1/32” (mdv21) 24 5/64” do not use this appliance if any part has been under water. Immediately call a qualified technician to inspect the appliance and to replace any part of the control system and any gas control which has be...
Page 5 * this installation information applies in the usa, for canadian installation refer to page 7 of this manual * (for u.S. Vent terminal installations).
Page 6 4..
Clearance above grade, veranda, porch, deck, or balcony 12 inches (30cm) clearance to window or door that may be opened 6 inches (15 cm) for appliances 10,000 btuh (3 kw), 9 inches (23 cm) for appliances > 10,000 btuh (3 kw) and (30 cm) for appliances > 50,000 btuh (15 kw). Clearance to permanently ...
Page 8 a vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves both dwellings. Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor..
Page 9 dv8 dv14 dv21 do not connect this appliance to a chimney flue serving a separate solid fuel appliance..
Page 10 7 1/4” 5/8” 6 1 . /2” 1 3/8” 3 7/8” 3 1 . /2” dv8 dv14 dv21 heater 8 1 . /2” 1 3/8” 4 7/8”.
Page 11 pilot hole wall bracket template 3-1/2” floor line marking for flue outlet hole marking for wall bracket mounting holes - 4 qty. Marking for gas inlet hole 3-1/2” floor line 9 3-1/2”.
Page 12 holes.
10 page 13 10 10
Page 14 10 gases outlet cap attach the gases outlet cap making sure that the threaded rod comes through the center hole in the cap. Secure the gases outlet cap by attaching the washers and the brass blind nut to the threaded rod using a screwdriver, tightening to stabilize the vent kit..
Page 15 electrode wires front of unit back of cabinet heater.
Page 16.
Page 17.
Page 18 call our customer service at 1 800 750 2723..
Page 19 call our customer service..
Page 20
Page 21 thermocouple pilot ignitor control knob ignition button.
Description glass viewer viewer frame viewer gaskets ignitor ignitor lock ignitor wire pushbutton control knob thermocouple pilot sparker pilot sparker wire pilot unit pilot gasket pilot injector ng pilot injector lpg burner injector ng burner injector lpg thermostatic valve ng thermostatic valve lp...
Page 23.
Page 24 faults to be prevented if for any reason this appliance is removed from the wall for maintenance or repair then re-installed, the venting must be properly reassembled and resealed to prevent any venting leaks. Refer to the “vent kit installation” section of this manual..
Page 25 pilot thermocouple ignitor correct pilot flame pattern pilot thermocouple ignitor incorrect pattern (no flame) pilot thermocouple ignitor incorrect pilot flame pattern yellow tips blue flame correct pilot flame pattern at high position incorrect pilot flame pattern at high position.
The company reserves the right of introducing any modifcation deemed convenient in order to improve the products, or due to any man- ufacture or commercial requirements, without previous notice, provided those modifcations are in accordance with the local gas code. This manual will help you obtain e...
Page 27.
Manufactured for: united states stove company 227 industrial park road, p.O.Box 151, south pittsburg, tn 37380 ph: (423) 837-2100 homcomfort is a registered trademark of united states stove company..
