1. DL manuals
  2. Occhio
  3. Spotlight
  4. Piu piano in LED
  5. Instructions Manual

Occhio Piu piano in LED Instructions Manual

Summary of Piu piano in LED

  • Page 1

    Più piano led più piano in led instructions.

  • Page 2

    2 electrical components must be fitted only by qualified personnel. The spotlight must be disconnected from the mains before any work is carried out on it. Maintain the minimum safety distance from flammable materials. Before working on the spotlight (fitting it, changing the bulb or inserts, aligni...

  • Page 3

    3 occhio più piano led and occhio più piano in led are led spotlights in safety class 2. The spotlights are optionally available with differently equipped heads. Product description contents 2 safety precaution s 3 product descriptio n 3 content s 2 fitting diagram 4 più piano mounting ring with cov...

  • Page 4

    4 fitting diagram – più piano with mounting ring and cover cut-out dia.: 144 mm ceiling thick- ness: 10-50 mm mounting ring tube piano in incl. Head installation depth: 135 mm tube piano incl. Head installation depth: 96 mm cover doppio cover b c s b c s c b b c s b c s b c s c b b c s led driver.

  • Page 5

    5 cut-out dia.: 166 mm ceiling thickness: 10-35 mm fitting diagram – più piano with plaster ring mounting ring plaster ring tube piano in incl. Head installation depth: 135 mm tube piano incl. Head installation depth: 96 mm b c s b c s c b b c s led driver.

  • Page 6

    6 fitting diagram – più piano with retaining ring for panels cut-out dia.: 132.5 mm ceiling thickness: 10-22 mm retaining ring tube piano incl. Head installation depth: 96 mm tube piano in incl. Head installation depth: 135 mm b c s b c s c b b c s led driver.

  • Page 7

    7 fitting diagram – più piano head fitting diagram – più piano tube + head head satinised glass colour filter (optional) satinised glass/ colour filter (optional) colour filter (optional) bulb (already fitted) head tube piano in tube piano lid b c s spot lens 40° lens lens.

  • Page 8

    8 1 preparing più mounting ring with cover create a circular opening with a 144 mm diameter. Ceiling thickness: 10 mm to max. 50 mm. Carry out any painting and decorating work. Dia. 144 mm 10-50 mm b c s b c s c b b c s.

  • Page 9

    9 1 preparing più mounting ring with cover tighten 3 screws. Check that the mounting ring is held in place firmly. Further installation: fitting place the mounting ring in the opening..

  • Page 10

    10 1 preparing più doppio mounting ring with cover create two circular openings each with a 144 mm diameter. Distance between the circle centres: 162 mm ceiling thickness: 10 mm to max. 50 mm. Carry out any painting and decorating work. Dia. 144 mm 162 mm 10-50 mm b c s b c s c b b c s.

  • Page 11

    11 1 preparing più doppio mounting ring with cover tighten 2 x 3 screws. Check that the mounting rings are held firmly in place. Further installation: fitting place the mounting rings in the opening..

  • Page 12

    12 1 preparing più plaster ring create a circular opening with a 166 mm diameter. Ceiling thickness: 10 mm to max. 35 mm. Dia. 166 mm 10-35 mm guide the plaster ring through the opening. Should the cavity be too shallow, unscrew the perforated plate from the plaster ring. Then pass the perforated pl...

  • Page 13

    13 1 preparing più plaster ring insert the plaster ring into the opening with the grooved edge facing downwards. Using 4 drywall screws (supplied), screw down the perforated plate of the plaster ring through the ceiling panel..

  • Page 14

    14 1 preparing più plaster ring adjust the plaster ring to the level of the plaster by screwing it in or out. To fix the position at which the plaster ring is set, screw the supplied screw into the plaster ring so that it is flush..

  • Page 15

    15 1 preparing più plaster ring insert the mounting ring into the plaster ring. Tighten 3 screws. Check that the mounting ring is held in place firmly..

  • Page 16

    16 1 preparing più plaster ring place the protective cover in the opening. Prime the ceiling and grooved areas of the mounting rings with primer. Take care to ensure that no primer is applied to the inside of the mounting ring. Allow primer to harden according to the instructions given..

  • Page 17

    17 1 preparing più plaster ring carefully remove the protective cover. To do so, pierce it in the middle if required. If necessary, remove any residual plaster from the inside of the mounting ring using fine sandpaper. Apply a thin layer of plaster. Apply a ring of wire mesh to protect against later...

  • Page 18

    18 1 preparing più retaining ring for panels lower the panel as required. Create a circular opening with a 132.5 mm diameter. Ceiling thickness: 10 mm to max. 22 mm. Carry out any painting and decorating work. Dia. 132.5 mm 10-22 mm b c s b c s c b b c s.

  • Page 19

    19 1 preparing più retaining ring for panels should it not be possible to lower the panel, fitting can also be carried out from below, through the opening (provided there is sufficient free space above). In this case, the two halves of the retaining ring are first passed through the opening, and the...

  • Page 20

    20 1 preparing più retaining ring for panels place the centring sleeve in the opening. Screwing in from above (e.G. For panel fitting): screw on the retaining ring using 4 screws of suitable length. Remove the centring sleeve. Further installation: fitting.

  • Page 21

    21 1 preparing più retaining ring for panels remove the retaining ring and centring aid. At the marks, drill 4 holes, each 5-6 mm in diameter screw on the retaining ring from below using the m6 screws provided. Remove the centring sleeve. Screwing in from below (e.G. For dry walling): fit the retain...

  • Page 22

    22 2 fitting – mounting the spot when delivered, the led bulb is already installed in the head. Do not touch the surface of the led (yellow surface). Push the black catch located between the cooling fins outwards and hold. Place the spot lens in the recess..

  • Page 23

    23 2 fitting – mounting the spot release the black toggle. The spot lens is locked in place by a spring mechanism. Check that the spot lens is held firmly in place..

  • Page 24

    24 2 fitting – mounting the spot insert the narrow end of the occhio tool (supplied) into the groove of the release pin. Turn the occhio tool until the release pin pops up. Insert the edge of the lens/opt. Colour fil- ter into the two springs and press against the springs. If a combination of two gl...

  • Page 25

    25 2 fitting – mounting the spot holding it in this position, clip the edge of the lens/opt. Colour filter into the notch on the release pin. Press the release pin in until it is flush. It clicks into its end position. The head is now fully prepared and ready to insert into the tube. Further install...

  • Page 26

    26 2 fitting - mounting the glass inserts/lens insert the edge of the glass insert(s)/lens into the two springs and press against the springs. If a combination of two glass inserts is used, the frosted glass is fitted on the inside. When delivered, the led bulb is already installed in the head. Do n...

  • Page 27

    27 2 fitting - mounting the glass inserts/lens holding it in this position, clip the edge of the glass insert(s)/lens into the notch on the release pin. Press the release pin in until it is flush. It clicks into its end position. The head is now fully prepared and ready to insert into the tube. Furt...

  • Page 28

    28 2 fitting – preparing the tube place the tube on a soft surface, with the lid facing upwards. If the tube is sealed, insert the wide end of the occhio tool (supplied) into the cut- out between the lid and tube. Turn the occhio tool, release the lid from the tube and take it off..

  • Page 29

    29 2 fitting – preparing the tube insert the fully assembled head into the tube. Caution insert the head and lens carefully, because on the più piano the lens protrudes at the bottom. Make sure you place the head on a soft surface. Guide the head cable through the opening on the lid..

  • Page 30

    30 fitting – preparing the tube remove the plug from the lamp cable supplied. Socket plug click the lid into place in the tube. To do this, raise the tube slightly. Ensure that the lid is fully closed..

  • Page 31

    31 fitting – preparing the tube connect the cables to the plug as shown in the diagram. Correct polarity must be observed. The spotlight is now fully assembled. Push the plug onto the pins on the lid. Further installation: fitting – electrification.

  • Page 32

    32 3 installation – electrification caution before fitting, disconnect all current- carrying lines from the mains supply. $ length of the supplied lamp cable: 0.5m maximum length of lamp cable: 10m più led spotlights are powered by a standard 700 ma led current source (driver). The current source ha...

  • Page 33

    33 3 installation – electrification occhio piú lamps are dimmable. The degree of dimming depends exclu- sively on the led driver used. Standard led drivers are not dimmable. The osram led drivers we offer permit infinitely variable dimming via 1-10v technology. Pri sec control port led 230 v control...

  • Page 34

    34 both assembled spotlights (piano/piano in) are inserted in the same way, regard- less of installation variant. Check inside the mounting ring for debris and residual plaster, and remove it using fine sandpaper. 3 installation – inserting the spotlight 1. Insert the spotlight into its mounting rin...

  • Page 35

    35 3 installation – putting the cover in place (for fitting with mounting ring only) place the matching cover over the moun- ting ring(s), ensuring that it is properly centred. The cover is held in place by magnets. If the spotlight has to be removed, to re- place the bulb for example, the cover mus...

  • Page 36

    36 3 adjusting the tube tip the più piano head to one side to reach the inner surface of the tube. By turning the tube, the spotlight can be adjusted to the level of the ceiling. On the version with the cover, a gap between the tube and cover can be closed in this way..

  • Page 37

    37 3 adjusting the head caution, risk of burning. Always let the spotlight cool before touching it. $ the più piano head can be moved up to 30° right round its circumference. The più piano in head can be moved up to 20° right round its circumference. 20° 30° 20° 30°.

  • Page 38

    38 4 removing the spotlight caution before fitting, disconnect all current- carrying lines from the mains supply. Caution, risk of burning. Always let the spotlight head cool before touching it. $ tip the più piano head to one side to reach the inner surface of the tube. On the version with the cove...

  • Page 39

    39 4 removing the spotlight the two spotlights (piano/ piano in) are removed in the same way, regardless of installation variant. 1. Holding the tube, turn the spotlight clock- wise as far as it will turn. 2. Press the spot- light upwards until it is flush. 3. The spotlight can now be removed. Some ...

  • Page 40

    40 4 removing/replacing the inserts remove the spotlight (see “removing the spotlight”). Disconnect the cable plug and socket. Caution before fitting, disconnect all current- carrying lines from the mains supply. Caution, risk of burning. Always let the spotlight cool before touching it. $.

  • Page 41

    41 4 removing/replacing the inserts using the wide end of the occhio tool or a wide screwdriver, open the lid of the tube. Insert the tool into one of the side grooves and turn to release the lid from the tube. Place the tube on a soft surface..

  • Page 42

    42 insert the narrow end of the occhio tool (supplied) into the groove of the release pin. Turn the occhio tool until the release pin pops up. Remove the spotlight head from the tube and place it on a soft surface, with the bulb facing upwards. 4 removing/replacing the inserts.

  • Page 43

    43 4 removing/replacing the inserts fitting inserts: fitting - mounting the glass inserts/lens press the glass insert/lens against the springs and remove from the groove on the release pin..

  • Page 44

    44 push the black catch located between the cooling fins outwards and hold. Before removing the spot lens: remove the lens and if necessary the colour filter. 4 removing the spot lens removing/replacing the inserts caution before fitting, disconnect all current- carrying lines from the mains supply....

  • Page 45

    45 remove the spot lens from the led holder. Do not touch the surface of the led (yellow surface). 4 removing the spot lens to fit the inserts/lens: fitting - mounting the glass inserts/lens to fit the inserts/lens: fitting – mounting the spot.

  • Page 46

    46 4 replacing the bulb $ caution before fitting, disconnect all current- carrying lines from the mains supply. Caution, risk of burning. Always let the spotlight cool before touching it. Before removing the led chip remove all the lenses/inserts. See: removing/replacing the inserts see: removing th...

  • Page 47

    47 4 replacing the bulb remove the black led holder from the heat sink. Rotate the led holder. Remove the led chip..

  • Page 48

    48 4 replacing the bulb attach the led chip to the pins of the led holder. To align the terminals of the led chip correctly: positive terminal of the led chip must point towards the positive marking of the led holder. Incorrect polarity can damage the led..

  • Page 49

    49 4 replacing the bulb rotate the led holder incl. Led chip and insert in the opening in the heat sink. The large cut-out in the led holder must point towards the black catch between the cooling fins (black arrow). Slightly tighten the allen screws using hex key no. 2. To fit the inserts/lens: fitt...

  • Page 50

    50 we recommend using a glass cleaner to clean both the metal and glass parts of the lamp. Always allow the lamp to cool down before cleaning. Care instructions your occhio specialist retailer will gladly answer any other questions www.Occhio.De info@occhio.De information & contact.

  • Page 51

    51 product description occhio più piano led occhio più piano in led rating p 13w current i 700 ma voltage u ≥ 20v lifespan t ≥ 20,000 h colour temperature t 3,000 k efficiency class eei a high colour led luminous flux f 680 lm colour rendering index cri ra 95 efficiency factor n 52 lm/w recommended ...

  • Page 52

    52 più piano led più piano nv b più piano nv c più piano nv s 40 chrome matt chrome bianco nero chrome matt chrome bianco nero chrome matt chrome bianco nero 1p 12 69 mm_ 1p 12 69 cc_ 1p 12 69 cb_ 1p 12 69 cn_ 1p 12 68 mm_ 1p 12 68 cc_ 1p 12 68 cb_ 1p 12 68 cn_ 1p 12 64 mm_ 1p 12 64 cc_ 1p 12 64 cb_...

  • Page 53

    53 più piano in led più piano in nv b più piano in nv s 40 più piano in nv c chrome matt chrome bianco nero chrome matt chrome bianco nero chrome matt chrome bianco nero 1p 22 69 mm_ 1p 22 69 cc_ 1p 22 69 cb_ 1p 22 69 cn_ 1p 22 64 mm_ 1p 22 64 cc_ 1p 22 64 cb_ 1p 22 64 cn_ 1p 22 68 mm_ 1p 22 68 cc_ ...

  • Page 54

    54 mounting bulb led driver mounting ring with cover doppio mounting ring with cover plaster ring retaining ring for panels high flux cri 85 / 900 lm / 700 ma high colour cri 95 / 680 lm / 700 ma led driver 700 ma chrome matt chrome bianco nero chrome matt chrome bianco nero 13 w 13 w 18 w 1m 11 00 ...

  • Page 55

    55 ma_90971_piu_piano_piu_piano_in_led_en.

  • Page 56

    Axelmeiselicht i axelmeiselicht gmbh wiener platz 7 rgb. D 81667 münchen fon + 49-89-44 77 86 30 fax +49-89-44 77 86 39 info@occhio.De www.Occhio.Com.