1. DL manuals
  2. Ocean Aire
  3. Air Conditioner
  4. 20AC series
  5. Engineering, Installation And Service Manual

Ocean Aire 20AC series Engineering, Installation And Service Manual

Manual is about: Deluxe Portable Air-Cooled spot cooler

Summary of 20AC series

  • Page 1

    Engineering, installation and service manual 2oac series deluxe portable air-cooled spot cooler form eism-2oac, 110114 rev 1.

  • Page 2

    Table of conents page general description …................................. 1 product data and specifications ............ 2 unit description standard features.................................. 3 applications / operation.......................... 4 electrical...........................................

  • Page 3

    Nomenclature 2o ac 24 1 2 deluxe portable voltage air-cooled single phase nominal capacity capacity rating 12..........12,000 btu/hr 18..........18,000 btu/hr 24..........24,00 btu/hr 36..........36,000 btu/hr 60……...60,000 btu/hr general description the oceanaire 2oac is a portable air-cooled spot ...

  • Page 4

    2 specifications 2oac.

  • Page 5

    Standard features cabinet the 2oac series spot cooler has a cabinet that is constructed of 18 gauge steel with a polyester powder coated finish that will compliment any decor. The cool blue front com- pliments any surrounding space, and is insulated with sound-absorbing insulation for cool, quiet co...

  • Page 6

    4 applications cooling mode—spot cooler the 2oac can be used in an open environment to cool specific objects or "spots". Spot cooling is a convenient and economical way to provide air conditioning where cooling the entire space is impractical. Cool air is discharged from the unit and is directed whe...

  • Page 7

    5 service cord all 2oac-series units are equipped with the standard ten foot long service cord with plug configurations and receptacle requirements as shown in this chart. 2oac1211, 2oac1811, 2oac2412 and 2oac3612 units come with lcdi (leakage current detection & interruption) devices that serve as ...

  • Page 8

    6 use of extension cords caution: for model 2oac1211 an extension cord can be used provided it is rated at least 15 amps @ 115 volts with grounding-type attach- ment plug and grounding type connector (load fitting) for model 2oac1811 an extension cord can be used provided it is rated at least 20 amp...

  • Page 9

    7.

  • Page 10

    8 condensate reservoir tank for 2oac models 2oac12, 2oac18, 2oac24 and 2oac36, a 5-gallon polyethylene tank is provided to collect condensate. The tank is located in the lower, front section of the unit. A high water level cut-out switch is used to stop the compressor and condenser fan automatically...

  • Page 11: Accessories

    9 ck-12pl ck-16 ck-12 ck-16 2dda-6 2dda-10 2dda-16 2nk-1 2nk-2 2nk-3 dep-10 2dep-12 dep-16 2dcp-1 2dcp-2 dcp-5 2oac unit accessories.

  • Page 12

    2oach – 2oac accessories nozzle kit 2nk-1 (2 x 4-inch) 2oac12 2nk-2 (2 x 6-inch) 2oac18, 24 2nk-3 (2 x 8-inch) 2oac36, 60 evaporator return air plenum dep-10 (10-inch round) 2oac12 2dep-12 (12-inch round) 2oac18, 24 dep-16 (16-inch round) 2oac36, 60 discharge duct adapter 2dda-6 (6-inch round) 2oac1...

  • Page 13

    Accessories ceiling panel duct kit, ck-12, ck-16 a ceiling panel kit is available for discharging the condenser air above a drop ceiling.. The ceiling panel duct kits are furnished with a white vinyl coated flexible duct that allows for convenient installation. A 2ft x 2ft ceiling duct- panel is inc...

  • Page 14

    Accessories discharge air nozzle kit assembly (2nk) the optional discharge nozzle kits are used to direct the condi- tioned air to a specific target area. By concentrating the airflow, the nozzles increase the air velocity towards production lines to cool personnel or equipment. In server rooms, the...

  • Page 15

    Accessories condenser return air plenum, 2dcp condenser return air plenums are available for installations where it is required to duct air to the inlet of the condenser. The plenum easily attaches with one screw to the back of the unit, and is provided with flange(s) for connecting 12-inch flexible...

  • Page 16

    Plenum kit duct/flange 2oac12 2oac18 2oac24 2oac36 2oac60 filters dep-10 10 inch ü (1) 10”x20”x1” 2dep-12 12 inch ü ü (1) 15”x25”x1” dep-16 16 inch ü ü (1) 12”x30”x1” (1)15”x30”x1” maximum equivalent feet 25 50 50 50 100 est. External static pressure (.20) (.25) (.25) (.25) (.50) accessories evapora...

  • Page 17

    Accessories discharge duct adapter, 2dda discharge duct adapters are available for applications where ducted evaporator discharge is required. The adapters can be easily installed on the unit without fasteners, and be installed for either vertical or horizontal ducting. The standard discharge grille...

  • Page 18: Warranty

    Installation instructions receiving—inspection : upon receiving your 2oac unit, inspect the packaging for any damage. All units are shipped on a skid, and packaged in a triple-wall carton for added protection. In shipment, some wear may occur on the packaging. If the packaging is heavily damaged or ...

  • Page 19

    17 oceanaire deluxe electronic controller when power is connected, the controller will display “888” momentarily, and will then go blank. Press the power button, then press the temp select button until the set point is displayed. Adjust the set point to the desired temperature, and the unit will hea...

  • Page 20

    Controller programming menu 1) make sure the unit has power. 2) pushing the power button, turn the unit “off”. 3) press the following buttons in sequence “s-u-d-s”: 4) the display will begin flashing p1 and a number. If there is no display, repeat the sequence, making sure the unit has power, but is...

  • Page 21

    To check the number of hours on the unit 1) disconnect unit power, and reconnect unit power. 2) when “888” appears in display, push and release the arrow down button 3) the first set of numbers displayed reads thousands of hours: 02 = 2000, 04 = 4000 hours, 00 means less than 1000 hours. 4) the seco...

  • Page 22

    Replacement procedure for parts it is recommended that all oceanaire units be serviced by a licensed technician warning—to avoid injury, disconnect unit power prior to servicing a. Fan motors 1. Remove cabinet's left-side panel (when looking at the front of the unit). 2. Evaporator fan motor—disconn...

  • Page 23

    Troubleshooting guide the following steps and procedures are recommended for correcting the problems indicated. In the event that the problem can not be corrected, service may be required. Service should be performed by a qualified air conditioning service technician problem: unit does not power up ...

  • Page 24

    22 preventive maintenance 2oac spot coolers are designed to last a long time and to give maximum performance and reliability with minimum maintenance. To prolong the life of the unit, regular maintenance must be performed as specified below: blower motors the motors on all units have permanently lub...

  • Page 25

    2oac12 interior view 23.

  • Page 26

    24.

  • Page 27

    25.

  • Page 28

    26.

  • Page 29

    27.

  • Page 30

    28.

  • Page 31

    29.

  • Page 32

    30

  • Page 33

    31.

  • Page 34

    Manufacturer’s limited warranty the manufacturer (oceanaire, inc.) warrants to the original owner that the product will be free from defects in material or workmanship for a period not to exceed one (1) year from date of installation. If upon examination by the manufacturer the product is shown to h...

  • Page 35: Useful Information

    Useful information model: serial number: date purchased: installed by: date installed: for technical support, or to locate a distributor for service parts, contact oceanaire at (847) 583-0311 or 1-866-getaire (438-2473). Please indicate the model number and serial number of the unit to assure proper...

  • Page 36

    Form eism-2oac, 110114 rev 1.