P-Tronic 100 Instruction Manual - page 17

Summary of 100

  • Page 1

    Instruction manual gb p-tronic 40p - p-tronic 70 - p-tronic 100 this manual is completed by the “ce operating and service maual” edition rev.20130304 p-tronic 40p - 70 - 100

  • Page 3

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 index chap. Description page introduction 1. Conformity declaration 1 1.1 raee norm 2 1.2 safety precautions 2 1.3 thermal limits (en 60974-1) 2 2. Safety device 3 2.1 safety device signal 3 3 explanation of technical specification 3 3.1 techn...

  • Page 4

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 warning important: before starting the equipment, read the contents of this manual, which must be stored in a place familiar to all users for the entire operative life-span of the machine.This equipment must be used solely for cutting operatio...

  • Page 5

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 1. Conformity declaration ter srl – 36030 caldogno (vi) – italy declares that the machines descripted in this manual must be use solely for professional purposes in an industrial environment and they are manufactured in compliance with the ins...

  • Page 6

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 1.1 raee norm the symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the ap- plicable collection point for the recycling of electrical and electronic ...

  • Page 7

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 led p-tronic 70 - 100 2. Safety devices this system comes equipped with the following safety devices: (see table 1 ) overload cut out: to avoid overload while cutting. Pneumatic: located on the torch inlet to prevent low air pressure. Electric...

  • Page 8

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 3.1 technical specifications table technical data p-tronic 40p p-tronic 70 ptronic 100 code v0042aa voo82aa v0059aa main supply (-10%/+15%) vac 1ph x 230v 3ph x 400v 3ph x 400v frequency hz 50/60 50/60 50/60 main power (60%) kva 6 / ed50% 11 1...

  • Page 9

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 5. General description this apparatus is a constant direct current (dc) generator, designed to cut electro conductive materials (metals and alloys) by a plasma arc process. The plasma gas is generated by using compressed air. 5.1 front panel d...

  • Page 10

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 step 4: the reducer has an “in” nipple that has to be connected to the compressed air net and an “out” nipple: provide an 8x6 teflon tube of about 30 cm to link the out- put nipple “out” with the machine air in- put nipple positioned on the ba...

  • Page 11

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 p-tronic 70 7. Plasma p-tronic 70 general description this apparatus is a constant direct current (dc) generator, designed to cut electro conductive materials (metals and alloys) by a plasma arc process. The plasma gas is generated by using co...

  • Page 12

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 in certain applications the contact cutting may be required even with currents over the 40a (ex. High cutting speed on thin metal sheet or on high ticks where a high cutting precision is required). In those applications , use the spare parts d...

  • Page 13

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 - 9 - 9. Use of the equipement: a) connect the earth clamp cable to the work piece b) connect the machine to the power supply net and turn on the power switch (8). The green led on/off light on the yellow led lights up if the torch safety circ...

  • Page 14

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 warning: the generator is equipped with a ter pt-100 plasma torch, cod z0042aa 6 mt long. This torch has to be considered as integral part of the generator and its functioning and safety are guaranteed only with the origi- nal torch. For any s...

  • Page 15

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 11.1 standard stand off in solid cutting this is the typical and most commun cutting type; you can adjust the current from a minimum of 20a to a maximum of 100a. Once the cutting is terminated the arc strikes off and it can be reactivated pres...

  • Page 16

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 11.3 grating in grating cut position, the minimum current stays at 20a and the maximum at 40a. When the arc moves from the solid to the grating open area, the generator returns automatically in pilot arc condition and the cutting arc starts ag...

  • Page 17

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 12. Use of the equipement: a) connect the earth clamp cable to the work piece b) connect the machine to the power supply net and turn on the power switch (8). The green led on/off light on the yellow led lights up if the torch safety circuit i...

  • Page 18

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 - 14 - pos. Description code 1 ter - 80 torch body z0043aa 2 ter - 80 electrode z0048aa 3 ter - 80 diffusor z0049aa 4 ter - 80 tip cutting 1,0 z0051aa 5 ter - 80 retaining cup z0055aa 6 ter - 80 spacer 2 points z0056aa 7 ter - 80 handle kit z0...

  • Page 19

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 - 15 - 14. Ter - 80 (for p-tronic 70) complete torch cod. Z0133aa pos. Description code 1 ter - 80 torch body z0043aa 2 ter - 80 electrode z0048aa 3 ter - 80 diffusor z0049aa 4 ter - 80 tip cutting 1,2 z0053aa 5 ter - 80 retaining cup z0055aa ...

  • Page 20

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 pos. Description code 1 ter - 100 torch body z0057aa 2 ter - 100 electrode z0060aa 3 ter - 100 diffusor z0062aa 4 ter - 100 tip cutting 1,5 z0068aa 5 ter - 100 outer nozzle z0071aa 6 ter - 100 double pointed spacer z0072aa 8 ter - 100 handle k...

  • Page 21

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 - 17 - 1,5 pos. Description code 1 ter - 100m torch body z0141aa 2 ter - 100 electrode z0060aa 3 ter - 100 diffusor z0062aa 4 ter - 100 tip cutting 1,5 z0068aa 5 ter - 100 outer nozzle z0071aa 7 ter - 100 fiber glass positioning tube z0142aa 8...

  • Page 22

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 11 14 10 9 12 13 15 16 18 19 17 pos. Description code - 18 - 5 6 4 7 3 2 1 8 17. Spare parts p-tronic 40 p spare parts p-tronic 40 p single-phase p-tronic 40p p-tronic 40p p-tronic 40p 1 knob r-37-231220-06-00 2 200a switch r-07-020000-13-00 s...

  • Page 23

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 18. Electric wiring diagram - 19 - p-tronic 40p.

  • Page 24

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 11 25 22 10 23 19 19. Spare parts p-tronic 70 spare parts p-tronic 70 8 3 4 9 2 1 5 7 6 p-tronic 70 p-tronic 70 p-tronic 70 - 20 - spare parts p-tronic 70 p-tronic 70 26 20 17 27 14 24 18 29 28 15 21 13 n° description code 1 potenziometro plas...

  • Page 25

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 20. Electric wiring diagram p-tronic 70 - 21 -.

  • Page 26

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 21. Spare parts p-tronic 100 - 22 - spare parts p-tronic 100 p-tronic 100 4 5 7 6 3 9 2 1 8 n° description code 1 potentiometer knob plasma 70/100 r-37-231410-05-01 1 potenziometro plasma 40/70/100 r-01-040105-01-00 p1 2 0÷10 bar manometer pla...

  • Page 27

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 20 10 11 12 13 14 15 16 17 18 19 21 22 23 24 25 26 27 21. Spare parts p-tronic 100 p-tronic 100 spare parts p-tronic 100 n° description code 10 emc board r-51-ph02-085-b-rl pcb1 11 auxiliar transformer r-03-010500-16-00 t2 12 logic control boa...

  • Page 28

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 22. Electric wiring diagram p-tronic 100 - 23 -.

  • Page 30

    Gb en gl is h instruction manual p-tronic 40p - 70 - 100 ter srl via giacomo leopardi, 13 - 36030 caldogno (vi) italy • ph: +39 0444 586440 - fax: +39 0444 905764 • e-mail: info@terwelding.Com.