1. DL manuals
  2. Pacific Living
  3. Oven
  4. PL8304SS
  5. Owner's Manual

Pacific Living PL8304SS Owner's Manual

Summary of PL8304SS

  • Page 1

    1 pacific living outdoor gas oven owner’s manual (for the followings models: pl8430ssbg070, pl8304ss, and pl8430ss) warning improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read this instruction manual thoroughly before installing or servicin...

  • Page 2: Oven Operation 1-2-3

    2 attach your receipt here serial number____________________ purchase date____________________ questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-410-0408, monday - friday, 8 a.M. - 5 p.M., pst. Oven operation 1-2-3 before cooking: st...

  • Page 3

    Table of contents 3 safety information…………………………………….………...….………….………….…………. 4 package contents…..………………..…..….……...…...................………………………………. 6 hardware contents……………………………………………………………….………………….. 7 assembly instructions………………..……………….……………………………………………..8 lp gas assembly…………………………………………………….....

  • Page 4

    Safety information 4 please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call customer service at 1-866-410-0408 monday to friday from 8 a.M. To 5 p.M. Pst. 1. The installation of this ap...

  • Page 5

    Safety information 5 15. Use only the gas pressure regulator supplied with this appliance. This regulator is set for an outlet pressure of 11.0 wc. 16. The cylinder used must include a collar to protect the cylinder valve 17. Do not store a spare lp-gas cylinder under or near the appliance 18. Never...

  • Page 6

    Package contents 6 part description quantity part description quantity a main body 1 e fat cup 1 b cooking grill 2 f smoker box 1 c pizza stone 1 g flame tamer 1 d bottom grill 1.

  • Page 7

    7 hardware contents the following list is included inside the outdoor oven carton: battery 1 pc the following list is not included inside the outdoor oven carton, but needed when the user is assembling the outdoor oven. Phillips head screwdriver 1 pc the following list is not included inside the out...

  • Page 8

    8 assembly instructions before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Assembly tip! (please lightly tighten the screws during assem...

  • Page 9

    9 3. Use screw m6*12×2 pcs to fix the left side panel onto the base panel of the stand. (note: the panel should have the “small holes at the top” to the front of the cart assembly) 4. Use screw m3*12×2 pcs and nut m3×2 pcs to attach the door magnet onto the right side panel. (note: please attach the...

  • Page 10

    10 6. Use screw m4*10×4 pcs and nut m4×4 pcs to attach the transformer assembly onto the outside of the back panel of the stand. (note: these screws can be tightened at this time) 7. Use screw m6*12×5 pcs to attach the stand base panel onto the base panel, between the two side panels..

  • Page 11

    11 8. Use screw m4*10×4 pcs to fix the stand door horizontal beam between the two side panels. (note: please fasten the upper two screws first, and then the lower two screws.) 9. Use screw m4*10×4 pcs to fix the stand top panel on the top of the two side panels and back panel. (note: these screws ca...

  • Page 12: Almost Finished!!

    12 11. First, insert the door lower axis into the hole in the base panel. Next, push down the door upper spring axis and let go of the spring when it is pointed to the hole in the horizontal beam. (note: you may need to add 1 or 2 washers 18*6.4*1 on the bottom pin so the door will close evenly) alm...

  • Page 13

    13 13. Use screw m5*10×16 pcs to attach side shelf bracket×4 pcs onto the drawer side panels. (note: arrows face up) 14. Using one of the screw m5*10 to fix the match holder onto the front bracket of right side shelf. (this step may be skipped if you do not want or need a “match holder” on your unit...

  • Page 14

    14 16. Use screw m4*8×3 pcs to fix the chimney assembly onto the top of the oven exterior. (note: these screws can be tightened at this time) 17. Use screw m5*35×4 pcs to fix the back heat shield onto the back panel of the oven. The order is: screw→back heat shield→heat insulation washer→flat washer...

  • Page 15

    15 19. Insert the fat cup into the back of the oven. 20. Insert the battery into the electronic ignition. Unscrew the button and place battery positive (+) tip facing out. Screw button back on. Your complete outdoor oven is now assembled. L.P. Gas installation gas ovens that are set to operate with ...

  • Page 16

    16 5. Make sure all burner knobs are in the off position. 6. Connect the hose and regulator assembly to the tank valve (see fig. 6). Hand-tighten the quick coupling nut clockwise to a full stop. Do not use a wrench to tighten because it could damage the quick coupling nut and result in a hazardous c...

  • Page 17

    17 warning: the type i connective coupling (see fig. 7) supplied with your oven must not be replaced with a different type of oven/tank connection system. Removal will result in loss of warranty, gas leakage, fire and severe bodily harm. Pig 7 external thread thermally sensitive nut type i valve han...

  • Page 18

    18 l.P. Tank information never use a dented or rusted l.P. Tank or cylinder with a damaged valve. L.P. Cylinders are equipped with an o.P.D. (overfilling prevention device). The device shuts off the flow of gas to a cylinder after 80% capacity is reached. This limits the potential for release of gas...

  • Page 19

    19 pre-operation leak testing although all gas connections on the oven are leak tested prior to shipment, a complete gas tightness check must be performed at the installation site due to possible shifting during shipment, installation or excessive pressure unknowingly being applied to the unit. Peri...

  • Page 20

    20 warning do not use the oven in garages, breezeways, sheds or any enclosed area. Never operate the oven in enclosed areas as this could lead to a carbon monoxide buildup, which could result in injury or death. Place the oven on a level surface. Avoid moving the oven while it is in operation. Prepa...

  • Page 21

    21 warning: place the oven on a flat, level surface. Before the conversion, make sure all control knobs are in the off position, lp tank valve is closed, and tank is disconnected from regulator and removed from oven. Ng conversion instruction: before the conversion, make sure all control knobs are i...

  • Page 22

    22 use a screwdriver to loosen the screw that is used to fasten the burner cover. Turn the burner cover until the hole marked “ng” overlaps with the fixing hole on the burner. Put the screw back into the holes and tighten again. Use orifice removal tool to remove theφ1.2 lp orifice from the pizza ov...

  • Page 23

    23 put the burner back into the oven and insert the ignition wire into the original position. Use the 10x12 mm spanner to fix the thermocouple back into the oven again. Finally, fasten the burner with the original screws. Put back the two cooking grills, smoker box, pizza stone and base grill into t...

  • Page 24

    24 use the screw driver to put the conversion screw into the knob. When converting to natural gas, please be aware that the low heat setting of the main burners and searing burner is “ng low,” as shown on the control panel. “lp low” setting is not applied when converting to natural gas. Warning: ple...

  • Page 25

    25 important: after your outdoor kitchen is converted to natural gas, the working pressure for natural gas is 7-inche water column (wc). Gas pressure is affected by gas line size and the length of gas line run from house. Follow the recommendations in the chart below. From house to oven distance tub...

  • Page 26

    26 never attach an unregulated gas line to the appliance. Connection to an unregulated gas line can cause excessive heat or fire. Verify the type of gas supply to be used, either natural gas (n.G.) or liquid propane (l.P.), and make sure the serial plate agrees with that of the supply. Conversion ki...

  • Page 27

    27 . Clearance to combustible construction: a minimum of 61 cm (24 inches) from the sides and back must be maintained from the gas oven above and below the cooking surface to adjacent vertical combustible construction. Clearance to non-combustible construction: a minimum of 61 cm (24 inches) clearan...

  • Page 28: Present!!

    28 warning heat and smoke exhaust out of the chimney and the ventilation holes on the bottom of two oven side panels (see fig. 8). Make sure to keep anything that could be damaged by heat or smoke away from the heat and smoke exhaust holes. General rules do not leave the oven unattended while cookin...

  • Page 29

    29 operating instructions oven burner lighting warning: do not lean over oven when lighting. Turn off lp supply at cylinder when appliance is not in use. Main burner lighting illustration: 1. Check that the control knobs are in the off position. 2. Open valve at tank fully by turning counterclockwis...

  • Page 30

    30 using the oven light light operation instruction 1. Make sure the light’s power switch on the control panel is in the “off” position. 2. Connect power plug to properly grounded outlet. 3. Turn the light’s power switch to “on.” warning keep any electrical supply cord away from any heated surface. ...

  • Page 31

    31 care & maintenance general maintenance - keep outdoor cooking gas appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids. - do not obstruct the flow of combustion and ventilation air. - keep the ventilation openings of the cylinder enclosure free...

  • Page 32

    32 the drip tray should be cleaned periodically according to the using situation. Note: allow the drip tray to cool before attempting to clean. Oven racks the oven racks can be cleaned immediately after cooking is completed and after turning off the oven. Wear a barbecue mitt and scrub the oven rack...

  • Page 33

    33 definitions: (+) guard – guard is a portion of portable luminaries unit that prevents inadvertent contact with the bulb. It may be integrated with the uv filter or lamp containment barrier or as part of an enclosure or shade. (+) lamp containment barrier – lamp containment barrier is a portion of...

  • Page 34

    34 3. Use screw driver to loosen the screw that fix the light assy. 4. Use one hand to hold the metal back part of the light and one handle to hold the front glass cover and then take them apart. Then you can replace the bulb. 5. After replacement, use one hand to hold the metal back part of the lig...

  • Page 35

    35 6. Use m4*10 screw to fix the light assy. On to the back panel of the oven. 7. Use screw m5*35×4 pcs to fix the back heat shield onto the back panel of the oven. The order is: screw→back heat shield→heat insulation washer→flat washer→ oven back panel..

  • Page 36

    36 8. Finally, put back the two cooking grills, smoker box, pizza stone, base grill and flame tamer into the oven. Now you have finished replacing the bulb. Cleaning method follow steps below for glass cover removal. Use a damp towel to clean the surface of glass cover. Make sure the glass cover is ...

  • Page 37

    37 replacing battery for electrical igniter: 1. Remove the igniter cap by turning clockwise; 2. Replace the battery; 3. When installing new battery, ensure it is installed with the proper polarity; 4. Put on the igniter cap back by turning counterclockwise. Warning: 1. To protect against electric sh...

  • Page 38

    38 2. Loosen the m4*10 screw * 7 pcs that fix the door exterior and interior, and then loosen the m4*10 screw * 4 pcs that fix the door hinge. Then loosen the shoulder screw that attaches the door handle. 3. Use spanner 19# to loosen the nut that fix the temperature gauge. And then you can completel...

  • Page 39

    39 5. Use spanner or hand directly to tighten the nut that fix the temperature gauge on the glass. You can set the torque of the spanner at 4.0kgf*cm. 6. Use m4*10 screw * 4 pcs to fix the door onto the oven. Now you have finished cleaning the oven door..

  • Page 40

    Troubleshooting 40 many solutions given here can make your cooking experience safer and more enjoyable. You can also call the customer service department at 1-866-410-0408, 8 a.M. – 5 p.M., pst, monday to friday. Problem possible cause corrective action oven will not light. 1. The ignition wire came...

  • Page 41

    Troubleshooting 41 burner orifice size main burner Φ1.8 mm 2. Clear ports of any obstructions. 3. Refill the lp tank. Low heat, lp gas. The propane regulator assembly incorporates an excess flow device designed to supply the oven with sufficient gas flow. Rapid changes in pressure can trigger the ex...

  • Page 42

    Warranty 42 pacific living inc. Outdoor oven limited one (1) year warranty pacific living outdoor ovens are covered under manufacturer warranty for one full year from the date of purchase. The warranty is for parts and labor and at the discretion of pacific living the unit will be repaired or replac...

  • Page 43

    Exploded diagram 43 for replacement parts, call our customer service department at 1-866-410-0408, 8 a.M. – 5 p.M., pst, monday to friday. 74 69 70 71 72 73 68 63 57 62 59 58 61 60 44 40 39 53 52 51 49 50 48 47 38 37 45 46 15 7 31 20 30 29 19 18 17 32 33 34 35 36 16 14 13 12 11 10 9 8 67 56 65 66 64...

  • Page 44

    Exploded diagram 44 no. Part name qty no. Part name qty 1 heat spacer 4 38 grease tray left bracket 1 2 back heat-shield 1 39 oven back support 1 3 light assy. 1 40 grease tray right bracket 1 4 light bracket 1 41 oven right supporting assy. 1 5 handle latch 1 42 light transformer 1 6 gas pipe 1 43 ...

  • Page 45

    Replacement parts list 45 1 、 bg070-01 oven exterior * 1 pc 2. Bg070-02-00b oven interior * 1 pc 3. Bg070-24 burner bracket beam * 1 pc 4. Bg070b-03-01 oven back panel * 1 pc 5. Bg070-03a oven back heat shield * 1 pc 6. Bg070-10-00b burner assy. * 1 pc 7. Bg070-18 cooking grate * 2 pcs 8. Bg070-17b ...

  • Page 46

    Replacement parts list 46 25. Bg070b-38 oven door glass * 2 pc 26. Bg070-30 temp. Gauge * 1 pc 27. Bg070-12-00 oven door handle assy. * 1 pc 28. Bg070-76-00 sideshelf * 2 pcs 29. Bg070b-30-01 left sideshelf bracket * 2 pcs 30. Bg070b-30-02 right sideshelf bracket * 2 pcs 31. Bg070b-57-00 oven left h...

  • Page 47

    Replacement parts list 47 49. Bg070b-53 trolley top panel * 1 pc 50. Bg070b-54 trolley door horizontal beam * 1 pc 51. Bg070b-50-00 trolley left sidepanel assy. * 1 pc 52. Bg070b-51-00 trolley right sidepanel assy. * 1 pc 53. Bg070b-52 trolley back panel assy. * 1 pc 54. Bg070b-55 trolley door exter...