- DL manuals
- Q-See
- Baby Monitor
- QSW8209
- User Manual
Q-See QSW8209 User Manual
Summary of QSW8209
Page 1
Qsw8209 lcd baby monitor wireless camera visit us on the web at http://www.Q-see.Com rev 092507.
Page 2
Contents contents contents contents 1 packing list 2 diagram 3 structure 4 installation 5 specifications 6 fcc and eu.
Page 3
1. Packing list 1) 2.4ghz wireless camera ╳ 1 2) 2.4ghz wireless receiver ╳ 1 3) av cable ╳ 1 4) power adapter for camera ╳ 1 5) power adapter for receiver ╳ 1 note: aa batteries are not included 2. Diagram.
Page 4
3. Structure 3-1. Layout of camera 3-2. Layout of receiver.
Page 5
4. Installation 4-1. Setting up the camera 1. Setup the camera in the desired location 2. Connect the camera to the adapter and then slide the power switch to the on position note: --this camera can also use dry batteries as a power source by loading 4 aa batteries into the battery compartment on th...
Page 6
Camera is not going to be used for a long period of time, please unplug the adapter and remove the batteries. * the camera can run off of batteries for up to 5 hours (ir off) 3. Rotate the rounded head of the camera to the desired angle for surveillance. 4-1-1. Camera channel setup 1. On the right s...
Page 7
2. Press the channel button on the receiver to select the same channel as the camera. When the channels match the picture will be displayed on the screen. 4-1-3. Camera alarm setup 1. The camera provides motion detection and sound detection. For each mode you can select 3 sensitivity levels: low, mi...
Page 8
You press the eliminate alarm button. Within 1 minute the motion alarm starts the next alarm circle. Sound alarm setup: this alarm will detect sound. If you slide the alarm setting switch to the sound position, and select the sensitivity level, the system enters sound alarm mode. When sound is detec...
Page 9
Note: --this receiver can also use dry batteries as a power source by loading 4 aa batteries into the battery compartment at the back of the camera with their polarities in the correct position. --the ac adapter will work instead of batteries after it is plugged in. If the camera is not going to be ...
Page 10
3. Set the channel of the receiver to the same channel as the camera by pressing the channel button continuously, the pictures will display on the screen when the channels match. Note ： ： ： ： for clearer pictures you can connect the receiver to a monitor/tv with the included av cable (yellow for vid...
Page 11
Slide “volume switch” to adjust the volume of the receiver. 2. Channel selection press “ch button” to select the desired channel. 3. Channel looping hold the “ch button” for three seconds to enter the loop mode. All the available channels will be displayed one by one (default interval is 5 seconds)....
Page 12
Camera imaging sensor type cmos picture total pixels pal:720×480 pixels; ntsc: 720×576 pixels horizontal resolution 380 tv lines view angle pal:55°; ntsc:55° minimum illumination 0lux bandwidth 18m night vision range 5m battery working time 5 hours (ir off) motion detection distance 5m (16ft) sound ...
Page 13
* actual transmission range may vary according to weather, location, interference and building construction. * all the specifications are subject to minor change without prior notice. 6. Fcc information this device complies with part 15 of the fcc rules. Operation is subject to the following two con...
Page 14
Eu environmental protection electrical waste products (discharged batteries) should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice. Trademarks all brand names and products are registered trademarks of t...
Page 15
Legal disclaimer warning: your security camera is a quality digital product. You have to take utmost care while handling this product in order to ensure its reliability & durability. Digital peripheral solutions inc. 8015 e crystal drive. Anaheim, ca 92807, 1-877-998-3440. Q-see tech support in u.S....