QCI LS5T-37 Owner's Manual

Summary of LS5T-37

  • Page 1

    For your safety read and understand the entire manual before operating machine modle number : □ ls5t-37 □ ls5t-52 serial number : both model number and serial number may be found on the main label. You should record both of them in a safe place for future use. Save this manual for future reference 5...

  • Page 2

    1 table of contents contents page safety warnings & cautions 2-4 application conditions 4 specifications 5 electrical requirements 5 contents of shipping container 5 set up and preparation for operation 6, 7 wiring diagram 7 plumbing diagram 7 log splitter operation 8, 9 freeing a jammed log 9 repla...

  • Page 3

    2 safety warnings & cautions symbol affixed to the machine safety warnings & instructions understand your log splitter read and understand the owner’s manual and labels affixed to the log splitter. Learn its application and limitations as well as the specific potential hazards peculiar to it. Inspec...

  • Page 4

    3 resistant lenses. They are not safety glasses. Do not put the log splitter on the ground for operations. This is awkward operating position that the operator has to bring his face close to the machine, and thus risks being struck by wood chips or debris extension cords improper use of extension co...

  • Page 5

    4 protective hair covering to contain long hair, preventing it from get caught in machinery. Don’t overreach floor must not be slippery. Keep proper footing and balance at all times. Never stand on log splitter. Serious injury could occur if the tool is tipped or if the cutting tools is unintentiona...

  • Page 6

    5 maintain your log splitter with care keep the log splitter clean for best and safest performance. Make the workshop childproof lock the shop. Disconnect master switches. Store the log splitter away from children and others not qualified to use it..

  • Page 7

    6 application conditions this log splitter is a home use model. It is designed for operating under ambient temperatures between +5 o c and 40 o c and for installation at altitudes no more than 1000m above m.S.L. The surrounding humidity should less than 50% at 40 o c. It can be stored or transported...

  • Page 8

    7 connect the main leads to a standard 230v+10% (50hz+1hz) electrical supply which has protection devices of under-voltage, over-voltage, over-current as well as a residual current device (rcd) which maximum residual current rated at 0.03a. Contents of the shipping container a. Log splitter b. Suppo...

  • Page 9

    8 1. Oil tank 2. Log pusher 3. Work table 4. Wedge 5. Lift handle 6. Support leg 7. Work table extension w/ log retaining plates 8. Switch 9. Motor 10. Pushbutton box 11. Wheels for minor moving only. 12. Lift handle 13. Hydraulic control lever 14. Control lever guard 15. Bleed screw 16. Oil drain b...

  • Page 10

    9 cause permant damage to the log splitter. 17. Max pressure limiting screw do not adjust the max pressure limiting screw ! Max pressure was set before the log splitter ex work and the max pressure limiting screw is sealed with glue to ensure the log splitter works under pressure no more than 5 tons...

  • Page 11

    10 log splitter operation.

  • Page 12

    11 this log splitter is equipped with “zhb” control system that requires to be operated by both hands of the user – left hand controls the hydraulic control lever while right hand controls the pushbutton switch. The log splitter will freeze upon absence of either hand. Only after both hands release ...

  • Page 13

    12 on it to split excessively hard wood. After this time interval, the oil under pressure will be overheated and the machine could be damaged. For such extremely hard log, rotate it by 90 o to see whether it can be split in a different direction. In any case, if you are not able to split the log, th...

  • Page 14

    13 release both controls. After the log pusher moves back and completely stops at its starting position, insert a wedge wood under the jammed log. Start the log splitter to push the wedge wood to go completely under the jammed one. Repeat above procedure with sharper slope wedge woods until the log ...

  • Page 15

    14 replace the hydraulic oil in the log splitter after every 150 hours of use. Take following steps to replace it. Make sure all moving parts stops and the log splitter is unplugged. Unscrew oil drain bolt with dipstick to remove it. Turn the log splitter on the support leg side over an 4 liters cap...

  • Page 16

    15 • aral vitam gf 22 • bp energol hlp-hm 22 sharpening wedge after using the log splitters for some time, sharpen the wedge of the log splitter using a fine-toothed file and smooth any burrs or crushed area along the cutting edge. Trouble shooting problem probable cause remedy suggested log is impr...

  • Page 17

    16 unfamiliar noise or vibrating a lot air sealed in hydraulic system while operating. Loosen bleed screw by 3 ~ 4 rotations before operating the log splitter bleed screw is not tightened before moving the log splitter. Tighten the bleed screw up before moving the log splitter. Oil drain bolt with d...

  • Page 18

    17 parts schematic (1).

  • Page 19

    18 parts schematic (2).