Summary of Big Button
Page 1
Qt big button.
Page 2
1 introduction thank you for purchasing our product which adopts excellent workmanship and exceptional reliability. Your telephone is designed to give you flexibility in use and high quality performance. To get the most from your new telephone, we suggest that you take a few minutes to read through ...
Page 3
2 are inserted or a power supply connected). ¾ do not disturb function ¾ transfer function between parallel phones (using 2 similar models) ¾ pre-dial and edit function ¾ redial function ¾ 5 sets of alarm clock ¾ adjustable lcd contrast ¾ set pabx code ¾ pulse/tone dialing mode compatible ¾ adjustab...
Page 4
Location description 3.
Page 5
4 getting started 1. Insert one end of the line cord into the line jack marked “line” at the base of the phone and the other end to the wall outlet from the telephone exchange or pabx. 2. Connect one end of the curly cord to the handset jack and the other end to the jack on the side of the base of t...
Page 6
Making a call ¾ from the handset 1. Lift the handset 2. When you hear dial tone, dial the desired number. 3. The telephone will start to time the conversation after 6 seconds. 4. To end the call, return the handset to the base. ¾ pre-dialing function 1. When the handset is on the base (in on hook co...
Page 7
6 ¾ deleting 1. In on-hook state, press the out key to scroll to the desired stored outgoing number. 2. Press the del key and the number is deleted 3. Or press and hold the del key for 3 seconds, all stored outgoing numbers will be deleted. New incoming call and ringer indicator new incoming call in...
Page 8
7 ¾ adjusting lcd contrast 1. In on-hook state, press the menu key and press ▲ key three times, the lcd displays set 4 lcd, press the menu key again, lcd displays lcd 5 2. Press ▲ or ▼ key to adjust the lcd contrast, a total of 8 levels can be selected. 3. Press the menu key to confirm and exit. ¾ s...
Page 9
8 ¾ voice announcement of caller’s number 1. In on-hook state, press and hold the talking set button located at the bottom of the telephone base for 3 seconds, the lcd displays talk 1 on(off) and “1” flashes. 2. Press ▲or ▼ key to select the number of repetitions of the announcement. Choose between ...
Page 10
9 operation should be done within 30 seconds from answering the call). The call can not be transferred if more than 30 seconds elapsed from when the call was answered, the other telephone will ring, pick up the handset to answer the incoming call. Note: use the same make of telephone for the above f...
Page 11
Music on hold ¾ hold music selection there are 6 selectable melodies. 1. In off-hook state, press the hold/ring key 2. Press the out key to select the desired music on hold melody. The music is played at the same time. 3. Press ▲ or ▼ key to adjust the volume of the melody. 4. Press the hold/ring ke...
Page 12
Under the selected number on the keypad. ¾ make a call from two-touch memory in on-hook state, press the memory key followed by the numeric key (0-9), the lcd displays the stored number, press or the rd key or pick up the handset to dial the number directly, or press the rd key twice to dial the num...
Page 13
12 the signal sent from the telephone exchange. The telephone will automatically return to standby mode and will allow the phone to ring upon receipt of the next incoming call. To answer the call the handset has to be placed back on the cradle and then can be picked up to answer the call. Low power ...
Page 14
13 area, usually 5). * check if the ringing volume is set to db0 last number redial and/ * when you first make a call try pressing the pause button for a or memory dialing don’t pause between the outside line access digit (eg:9 or 0) and the work on a pabx telephone number, you should later be able ...