1. DL manuals
  2. Raisecom
  3. Media Converter
  4. RC513
  5. User Manual

Raisecom RC513 User Manual

Manual is about: 10/100M Auto-negotiation Copper-to-Fiber Media Converter

Summary of RC513

  • Page 1

    Rc513/514-fe (rev. A) 10/100m auto-negotiation copper-to-fiber media converter user manual raisecom technology co., ltd. Dec, 2005.

  • Page 2

    Beijing raisecom science & technology co., ltd. Content 1. Safety notice ................................................................................................................. 2 2. Overview ......................................................................................................

  • Page 3: 1. Safety Notice

    Beijing raisecom science & technology co., ltd. 1. Safety notice please read the following notice carefully before installing and using the device, raisecom shall not be responsible for any loss that caused by violating safety notice. Rc513/514-fe (rev. A) has high sensitivity optical interface, so ...

  • Page 4: 2. Overview

    Beijing raisecom science & technology co., ltd. 2. Overview 2.1. Introduction rc513/514 series remote-end managed, bandwidth adjustable ethernet media converters are new generation media converters developed by raisecom. The remote-end management means that the network administrators can manage both...

  • Page 5

    Beijing raisecom science & technology co., ltd. 2.2. Model description part number description rc513-fe-s1 standalone, remote managed, 10/100mbps auto-sensing, single mode, single strand, dual wavelengths, 0-25km, rj45/sc rc514-fe-s1 module, remote managed, 10/100mbps auto-sensing, single mode, sing...

  • Page 6: 3. Technical Specification

    Beijing raisecom science & technology co., ltd. 3. Technical specification 3.1. Optical parameters p art n umber interface wavelength (nm) launch power (dbmw) receiving sensitivity (dbmw) typical range (km) attenuation (db/km) rc513-fe-s1 sc/pc-rj45 1310 -12 ~ -3 0 ~ 25 0.5 rc513-fe-s2 sc/pc-rj45 13...

  • Page 7

    Beijing raisecom science & technology co., ltd. 4. Construction & indicator 4.1. Front view and indicators 4.1.1. The indicators on the front panel rlk fdx col pwr tlk act lnk act rmd 100m optical rx link optical data tx/rx action eth data tx/rx action optical tx link bit rate duplex mode /collision...

  • Page 8

    Beijing raisecom science & technology co., ltd. Power supply power pwr on: power supply works in good condition; off: power supply disconnected. 4.1.3. 16-slot chassis (for rc514) front panel sketch pwr ps1 ps2 5v 12v 5v 12v raisecom the working conditions indicated by each indicator are as follows:...

  • Page 9: 5.  Function & Application

    Beijing raisecom science & technology co., ltd. 5. Function & application 5.1. Interconnecting media converters when connecting with other media converters, it is required to comply with the specific connecting requirements according to the following table. Otherwise, link faults or abnormal data tr...

  • Page 10

    Beijing raisecom science & technology co., ltd. 5.3. Full duplex configuration (rj45 port) 5.3.1. Rc513/514-fe series rj45 interface auto-negotiation the copper port/rj45 of other network equipment must be configured to “auto-negotiation” to ensure normal data transmission. 5.3.2. Rc513/514-fe serie...

  • Page 11

    Beijing raisecom science & technology co., ltd. 6. Installation & inspection 6.1. Matching fiber-optic cable with media converter rc513/514-fe-s1 series shall adopt single strand single-mode fiber. The connector of fiber shall be sc/pc. 6.2. Types of fiber-optic cable fiber-optic cable for multi-mod...

  • Page 12

    Beijing raisecom science & technology co., ltd. 6.5. Installation of dc power supply (for rc514) dc power supply provides three connectors: –48v, ground and 0v. These three connectors are connected respectively with –48v power cable, ground protection and 0v power cable. -48v 地 0v 6.6. Ambience work...

  • Page 13: 7. Dip-Switch Configuration

    Beijing raisecom science & technology co., ltd. 7. Dip-switch configuration 7.1. Explanation for sw20 setup sw20 switch has 8 bits and the functions for each bit are as follows in sequence: auto-negotiation enable/disable, rate 100m/10m, full duplex/half duplex, reserved (vacant), frame length 1916 ...

  • Page 14: 8. Network Management

    Beijing raisecom science & technology co., ltd. 8. Network management 8.1. Card/module information review with network management software, the status of rc513/rc514 series can be reviewed at the host site, and controlled/configured. The status information on “show module info” is as follows: no. St...

  • Page 15

    Beijing raisecom science & technology co., ltd. Command “show module info. Loop-back”. The results of test can be shown through show module info. 8.4. Show module info reset the host or remote-end modules can be reset through “host module reset”. The frame length after the reset is 1,916bytes, and t...

  • Page 16

    Beijing raisecom science & technology co., ltd. @2005 raisecom technology co., ltd. All trademarks are the property of their respective owners. Technical information may be subject to change without prior notification. － v36 15.