Raisecom RC953-8FE16E1 User Manual

Manual is about: Inverse Multiplexing Ethernet Gateway

Summary of RC953-8FE16E1

  • Page 1

    Rc953-8fe16e1 inverse multiplexing ethernet gateway user manual raisecom technology co., ltd (06/2006).

  • Page 2: Contents

    Contents 1. Cautions.............................................................................................................. 1 2. Overview............................................................................................................. 2 2.1. Main features ............................

  • Page 3: 1. Cautions

    Raisecom technology co., ltd 1 1. Cautions please read the following notices carefully before installing and using the device, raisecom does not respond to any loss that caused by violating safety notice. This series product is integrated device that has precise elements, please avoid violent shakes...

  • Page 4: 2. Overview

    Raisecom technology co., ltd 2 2. Overview rc953-8fe16e1 is an inverse multiplexing ethernet gateway that delivers ethernet services over existing tdm transportation network. It can be deployed in central site for aggregating subscribers or in customer premises enabling inverse multiplexing for enla...

  • Page 5

    Raisecom technology co., ltd 3 z e1 loop back and bert function z complete e1 line indicators on front panel z e1 interface type: 2 db37 for both balanced and unbalanced interfaces z snmp, console and telnet management (any of the 8 fast ethernet can be snmp network management interface) and support...

  • Page 6: 3. Parameters

    Raisecom technology co., ltd 4 3. Parameters 3.1. Basic configuration z main circuit: 8 fast ethernet ports, 16 e1 ports. Z power supply: two power supply modules, 90-264v/ac or -36v- -72v/dc. Z management interface: console, snmp network management interface (utilize any of the 8 fast ethernet port...

  • Page 7

    Raisecom technology co., ltd 5 and is configurable z there are three status indicators for each e1 circuit: los: loss of signal (local) lal: local e1 general alarm, including ais(alarm indication signal), lof( loss of frame), crc(cyclic redundancy check) ral: remote e1 alarm, including los, ais, lof...

  • Page 8: 4. How To Use

    Raisecom technology co., ltd 6 4. How to use 4.1. Front panel explanation 1 2 3 4 5 6 7 8 9 rc953-8fe16e1 figure 4-1 front table 4-1 explanation of rc953-8fe16e1 front panel n o. Explanati on indicator color description 1 grounding 2 sys and pwr indicator green sys, flashing indicates cpu work norma...

  • Page 9

    Raisecom technology co., ltd 7 off off on the first power supply works abnormally, the second works normally but the main circuit works abnormally. Off off off not powered on or neither of the power supply module works normally. 4 consol e local management port which connects to management pc 5 ethe...

  • Page 10

    Raisecom technology co., ltd 8 table 4-2: explanation of rc953-8fe16e1 rear panel numb er explanation description 1 power supply switch for the device on/off. 2 power supply connector two types, ac and dc..

  • Page 11: 5. Typical Application

    Raisecom technology co., ltd 9 5. Typical application figure 5-1 point-to-point topology figure 5-2 point-to-multi point topology.

  • Page 12

    Raisecom technology co., ltd 10 6. Installation & preparation 6.1. Preparation before installation please check if the models and part numbers are in consistence first, and also check if the equipments are damaged. There must be drying process if the equipment is damped. Please follow the following ...

  • Page 13

    Raisecom technology co., ltd 11 6.2.2. Connect the fast ethernet port connect one end of the cat. 5 utp cable with ethernet router/switch and one end of the cable with the fast ethernet port of rc953-8fe16e1. The lnk/act indicator will be on after correct connection. 6.2.3. Connect the snmp network ...

  • Page 14

    Raisecom technology co., ltd 12 connect “-48v” end with the lower electric level cable, “0v” end with higher electric level cable. Make sure no reverse connection, or no short circuited, and then turn on power. When power supply is turned on, the pwr indicator should be on. 6.2.6. Service configurat...

  • Page 15: 7.  Q & A

    Raisecom technology co., ltd 13 7. Q & a if there are any problems during installation and using, try the following proposals. If the problems still can not be solved, please contact distributors/agents for help. ● if pwr, pwr1 and pwr2 are all off please check if power supply cable is connected and...

  • Page 16

    Raisecom technology co., ltd 14 8. Appendix a: how to make console cable pin definitions: rj45 pins function ds9 pins 1 nc - 2 dsr# 6 3 rxd 3 4 gnd 5 5 gnd 5 6 txd 2 7 dtr# 4 8 nc - “-” indicates the relative rj45 pin is not connected (nc). Db9 pins which are not in the list are not connected (nc)..

  • Page 17

    Raisecom technology co., ltd 15 9. Appendix b: abbreviations eopdh ethernet over pdh pdh pseudo-synchronous digital hierarchy..

  • Page 18

    Raisecom technology co., ltd 16 @2006 raisecom technology co., ltd. All trademarks are the property of their respective owners. Technical information may be subject to change without prior notification..