Raisecom RCMS2101-30-FV35 User Manual

Manual is about: Standalone, Fiber Optic Ethernet Multiplexer

Summary of RCMS2101-30-FV35

  • Page 1

    Rcms2101-30-fv35 rcms2301-30-fv35 rcms2501-30-fv35 standalone, fiber optic ethernet multiplexer user manual raisecom technology co., ltd. (10/2005).

  • Page 2: 1. Cautions

    Raisecom technology co., ltd 1 1. Cautions please read the following notices carefully before installing and using the device, raisecom does not respond to any loss that caused by violating safety notice. Rcms2x01-30-fv35 provides two types of power supply: ac and dc. When using dc power supply, ple...

  • Page 3: Contents

    Raisecom technology co., ltd 2 contents 1. Cautions ............................................................................................................................................1 2. Overview .................................................................................................

  • Page 4: 2. Overview

    Raisecom technology co., ltd 3 2. Overview 2.1. Introduction rcms2101-30-fv35, rcms2301-30-fv35, and rcms2501-30-fv35 series ethernet multiplexers are ideal optical fiber transmission devices for point-to-point networks, medium-sized and small capacity networks, such as wireless communication base s...

  • Page 5

    Raisecom technology co., ltd 4 2.4. Equipment structure compact desktop design with dimension: 142mm (w) * 38mm * (h)* 178mm (d).

  • Page 6: 3. Parameters

    Raisecom technology co., ltd 5 3. Parameters 3.1. V.35 interface specification physical characteristic: compliant to v.35 interface specification type of interface: iso2593 female connector (34-pin female) working mode: dce bit rate: n*64kbps (n=1~31) at framed e1 mode 2048kbps at unframed e1 mode 3...

  • Page 7

    Raisecom technology co., ltd 6 ts[1] …… …… ts[31] v.35 banwidth ts[n+1] …… ts[0] ts[16] 3.5. Power supply power supply voltage: dc -48v, tolerance range -36v ~ -72v ac 220v, tolerance range 165v ~ 265v power consumption: ≤ 5w when full loaded 3.6. Ambience working temperature: 0 ~ 45℃ relative humid...

  • Page 8: 4. How To Use

    Raisecom technology co., ltd 7 4. How to use 4.1. Description of the front panel v35al pwr los lof err raisecom rcms2101-30-fv35 series tx rx 100m fdx act lnk eth l r sketch of the front panel for rcms2x01-30-fv35 series 4.1.1. Power indicator power indicator (green): if power is in good condition, ...

  • Page 9

    Raisecom technology co., ltd 8 connector type is dsc/pc. Tx stands for optical output, rx for optical input. Z for single strand fiber model, rcms2301-30-fv35 and rcms2501-30-fv35, the tx wavelength of rcms2301-30-fv35 is 1310nm, and the tx wavelength of rcms2501-30-fv35 is 1550nm. The fiber connect...

  • Page 10

    Raisecom technology co., ltd 9 terminal timing (a) — scte(a) i u terminal timing (b) — scte(b) i w request to send — rts i c clear to send — cts o d data set ready — dsr o e data carrier detect — dcd o f data terminal ready — dtr i h i—input; o—output 4.3. Bottom dip-switch there are 3 dip-switches ...

  • Page 11

    Raisecom technology co., ltd 10 0 1 1 1 1 15×64k=960k 1 0 0 0 0 16×64k=1024k 1 0 0 0 1 17×64k=1088k 1 0 0 1 0 18×64k=1152k 1 0 0 1 1 19×64k=1216k 1 0 1 0 0 20×64k=1280k 1 0 1 0 1 21×64k=1344k 1 0 1 1 0 22×64k=1408k 1 0 1 1 1 23×64k=1472k 1 1 0 0 0 24×64k=1536k 1 1 0 0 1 25×64k=1600k 1 1 0 1 0 26×64k...

  • Page 12

    Raisecom technology co., ltd 11 z the 7 th and 8 th bits: clock mode option 7 th bit 8 th bit timing resource option off off master clock (internal) off on v.35 terminal clock on off vacant on on slave clock (follow the link clock) users are advised to select the most suitable timing resource. When ...

  • Page 13

    Raisecom technology co., ltd 12 4.3.3. The setup for sw3: factory default setting all off z the 1 st bit: ethernet auto-negotiation capability enable/disable when this bit is switched to off, auto-negotiation capability is enabled. When this bit is switched to on, auto-negotiation capability is disa...

  • Page 14

    Raisecom technology co., ltd 13 of sw3 is switched to on. If the optical fiber is connected properly, the loop-back status can be viewed at the port of local router. Z the 8 th bit: local loop-back function local loop-back is performed at local v.35 interface and used for test and diagnosis the v.35...

  • Page 15: 5.  Installation and Test

    Raisecom technology co., ltd 14 5. Installation and test 5.1. Inspect after opening please first check if the models and part numbers are in consistence, and also check if the equipments are damaged. 5.2. Preparation before installation z carefully read this manual z prepare all kinds of the cable. ...

  • Page 16: 6. Troubleshooting

    Raisecom technology co., ltd 15 6. Troubleshooting if you have any problems during installation and usage, try to solve them by the following proposals. If the problem persists, please contact distributors for technical support. These following explanations and solutions of alarm for optical port an...

  • Page 17

    Raisecom technology co., ltd 16 7. Appendix a introduction of cable making a.1 v.35 cable making v.35 interface is compliant to v.35/iso2593: dce connector face – 34-pin female connector. It can be connected with standard dte cable. Please refer to part 3.2.2 for wire sequence. A.2 ethernet cable ma...

  • Page 18

    Raisecom technology co., ltd 17 @2005 raisecom technology co., ltd. All trademarks are the property of their respective owners. Technical information may be subject to change without prior notification..