Roadmaster 12" Subwoofer VSW120 Instruction Manual

Download

Print this page

Bookmark us

• Nail Set/Center Punch

• Marker/Pen

• Safety Glasses

• Electrical Tape

• Phillips Screwdriver

• Hammer

• Wire Cutter

• Electric Drill

with 1/16" bit

GIVE US A CALL, WE'LL HELP YOU INSTALL.

1-800-445-1797

PLEASE DO NOT RETURN PRODUCT TO STORE.

Visit us on the WEB

www.vr-3.com

For Information and Technical Assistance,

Call Toll-Free in U.S.A. and Canada.

Subwoofer Terminals

Wires from Amplifier

VSW120

12” Subwoofer

Dear Customer,

CONGRATULATIONS. The VSW120 Subwoofer, when used as described, will give you years

of dependable service in your car, truck, RV or mini-van. We have taken numerous measures

in quality control to ensure that your product arrives in top condition, and will perform to your

satisfaction. In the rare event that your VSW120 Subwoofer contains a damaged or missing

item, does not perform as specifi ed, requires warranty service or you have an installation

problem,

DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR TOLL

FREE NUMBER FROM THE U.S.A. AND CANADA (800-445-1797)

and ask to speak with

a member of our technical service team, or submit your questions by e-mail our web site

vr-3.com, and a member of our technical service team will respond by e-mail to your ques-

tions. Our in-house technical service team will expedite delivery of your part, advise you on

installation, or help troubleshoot a problem with you. If your product needs warranty service,

our technical service team representative will help you obtain the fastest remedy possible

under the warranty.

Before You Install

Tools Needed to Install

• 12” Embossed Polypropylene Cone

• 26.5 oz. Magnet Weight ±10%

• Black Rubber Surround

• 400 Watts Maximum Peak Power

• 40 watts RMS per Voice Coil

• 35 to 2000 Hz Frequency Response

• 2” ASV, Dual Voice Coil

• Impedance 4 Ohms +/- 15%

• Sensitivity 89db 1W/1M Minimum

• Quick Connect Terminals (Spade Lug Type)

Automotive audio equipment installations can be troublesome at times, even to the

most experienced of installation technicians. If you are not confi dent working with

electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or

other components of your vehicle, please call our toll free help line (800) 445-1797

and our in-house technical service team will answer your installation questions.

Most car stereos do not have enough power to drive separate subwoofers, if your

mobile auto audio system does not have a separate amplifi er installed, you will most

likely need to install one.

Before permanently installing the VSW120 speakers in your car, connect the wires

to the speakers according to your audio systems installation manual, in the approxi-

mate location you will install them. If you are satisfi ed with the location proceed with

the permanent installation.

If you are building your own sealed

box enclosure, it should have a vol-

ume of 1.5 to 2.0 cubic feet, and

made with a minimum of 5/8” thick

particle board or M.D.F.. Make

sure that you screw and glue it to-

gether for a proper seal, caulk all

seams, and joints with silicone rub-

ber caulking. The inner walls of the

enclosure should be covered with a

sound absorbing material. Maintain

polarity of the amplifi er and speak-

er for proper phase alignment. This

insures the VSW120 operates at

maximum effi ciency.

Seal the hole with silicone

caulking where the wire

passes through the side of

the speaker box.

Cover all inside walls of the enclosure

with a sound deadening material such

as Dacron batting.

5/8” thick

particle board

or M.D.F.

Give Us A Call, We’ll Help You Install

Speaker wire of 18 Gauge to 12 Gauge may be used with the VSW120C. You can

purchase speaker wire with spade lug type female disconnects pre-installed on one end.

Installation

To attach speaker wires (not

included) with female quick

connects (spade lug type) to

the speaker terminals.

Push the female quick

connects (spade lug type) onto

the terminals. Maintain proper

polarity by attaching the Posi-

tive Wire (+) to Positive Termi-

nal (+) and the Negative Wire (-)

to Negative Terminal (-).

If the female quick connects

can be easily pulled off, they

can be tightened a little bit by

lightly squeezing them with

a pair of pliers. Do not fl atten

them completely.

Wiring

Installing in a Enclosure

The VSW120 is designed to give you optimum bass performance when installed in a

sealed speaker enclosure.

Specifi cations

Read First!

Limited Warranty

VIRTUAL REALITY VIDEO LABS

products are designed and manufactured to provide a high level of trouble-free per-

formance. VIRTUAL REALITY VIDEO LABS

warrants, to the original purchaser, that its products are free from defects

in material and workmanship for 30 days from the date of original purchase, as part of our commitment to product

excellence. VIRTUAL REALITY VIDEO LABS

and/or its affi liates routinely improves the designs, materials or produc-

tion methods of its existing products. Because it is impractical to publicize all changes in every product, we reserve the

right to make such changes without notice.

CONDITIONS OF WARRANTY:

If during the 30 day warranty period your new product is found to be defective, VIRTUAL REALITY VIDEO LABS

will

repair such defect, or replace the product, without charge for parts or labor subject to the following conditions:

1. All repairs must be performed by VIRTUAL REALITY VIDEO LABS

and/or its affi liates in Eatontown, New Jersey.

2. The equipment must not have been altered or been damaged through negligence, accident, or improper operation.

3. The replacement of parts are exempted from this warranty when replacement is necessary due to normal wear and tear.

4. All warranty claims must be accompanied by a copy of the sales receipt or bill of sale.

5. Repair or replacement parts supplied by VIRTUAL REALITY VIDEO LABS

under this warranty are protected only for

the unexpired portion of the original warranty.

6. In the case of car stereos, this warranty does not extend to the elimination of car static or motor noise; correction of

antenna problems; costs incurred for the removal or reinstallation of the product; damage to tapes, speakers, acces-

sories or car electrical systems.

7. VIRTUAL REALITY VIDEO LABS

will not be responsible for any charge incurred for installation.

OWNER’S RESPONSIBILITIES:

VIRTUAL REALITY VIDEO LABS

will make every effort to provide warranty service within a reasonable period of

time.

SHOULD YOU HAVE ANY QUESTIONS ABOUT SERVICE RECEIVED, OR IF YOU WOULD LIKE ASSISTANCE IN OB-

TAINING SERVICE, PLEASE CALL TOLL FREE 1-800-445-1797, 8:30am - 4:30pm EST.

In order to provide you with the proper warranty service, we request that you adhere to the following procedure:

1. Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service.

2. If it is necessary to return your product for service, please return it securely packed, preferably in the original shipping

carton, and freight and insurance prepaid to the following address: VIRTUAL REALITY VIDEO LABS, Service Depart-

ment, 41 James Way, Eatontown, New Jersey 07724.

3. Please include a detailed explanation of the problem you are having.

4. If your product is found by VIRTUAL REALITY VIDEO LABS

to have a defect in material or workmanship, within

the warranty period, it will be repaired or replaced at no charge and returned to you prepaid. Where permitted by Iaw

VIRTUAL REALITY VIDEO LABS

liability shall be limited to that set forth in this warranty. This warranty shall be the

exclusive remedy of the purchaser.

Notes

Frequently Asked Questions

What if there is no sound?

1. Your stereo may have a blown fuse.

Replace fuse with the same amperage and style.

2. You may have improper wiring.

Refer to the wiring guide that came with your stereo/amplifi er. Check all wires for a secure

connection.

What if the sound volume is low?

Your stereo may not have enough power, you may have to install an amplifi er to drive a

subwoofer.

Why do I have a whining noise coming from the subwoofer?

You may have poor fi ltering of your alternator. If that is the case, then you may need to add

an alternator fi lter to the power lead.

Why do I have odd sounding noises coming from the subwoofer?

You may have corroded battery terminals and/or a weak battery. If the terminals on the

battery are corroded, clean them; then check the sound. If the sound system is still making

noises check battery strength. If it is low recharge or replace the battery.

Location Of Subwoofers

Virtual Reality Sound Labs

makes no other warranty of any kind, expressed or implied; and all implied warranties, are

hereby disclaimed by Virtual Reality Sound Labs

and excluded from this warranty, Virtual Reality Sound Labs

, the

manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or consequential, arising

out of the use or intended use of the product

and/or its affi lantes. US and Foreign Patents Pending. 071608 Printed in China 00000

Recommendations for Positioning the VSW120 in Your Vehicle:

Cars: Hatch Back or Trunk

SUVs: & Mini Vans: Cargo Area

Pick-up Trucks: Behind Front Seat

All auto audio components must be securely mounted. Driving styles and

road conditions such as sudden stops, sharp curves, and bumpy roads may

cause unsecured items to move about the vehicle, causing physical injuries

to vehicle occupants and/or vehicle damage.

Before installing in an enclosure use the VSW120 as a guide to mark the enclosure

for pilot holes. When you have marked the pilot hole positions drill them with a bit

that is smaller than the screws you will use to secure the speaker to the enclosure.

Attach the positive (+)

and negative (-) wires

found inside the

enclosure box to the

VSW120 terminals. At-

tach Positive (+) to posi-

tive (+), and negative (-)

to negative (-).

Place the subwoofer

into the opening of the

enclosure. Then align

the screw holes of the

subwoofer with the pilot

holes that you drilled.

Tighten the screws.

Place a subwoofer grill

(optional) over the sub-

woofer, then fasten the

subwoofer grill in place.

Attach wires from audio

source to the terminals

on back of the enclo-

sure.