Summary of BC 90(1+1)
Page 1
Bc 90 (1 1) + ® use and maintenance manual gb.
Page 2
Assembling instruction for motor-mower box contents weight (kg) sickle bar bar mechanism machine connect sickle bar position the handlebar tighten the 4 screew s1 s3 s2 s1 s2 46,5 ÷ 47 14 ÷ 21,5 9,8 ÷ 12,5 a b c s3.
Page 3: Motor-Mower
Motor-mower bc 90 (1+1) before using the motor-mower carefully read the instructions given in this manual.
Page 4
2 table of contents page introduction.................................................... 3 safety regulations ....................................... 3 general notices............................................. 3 starting the engine ...................................... 3 operating of the motor-...
Page 5
3 introduction • this manual provides use and maintenance in- structions, technical specifications, and safety pre- cautions for motor-mower: − model bc 90 (1+1) in the versions with gasoline engines. • for the sake of clarity and ease of identification, the different motor-mower models are identifi...
Page 6
4 starting the engine • disengage all control levers before starting the mo- tor. Keep your feet clear of the attachments fitted to the machine. • do not run the engine in a closed ambient where the exhaust gases can collect. They contain car- bon monoxide that is highly toxic. • do not interfere wi...
Page 7
5 identification data motor-mower identification the serial number is stamped on the engine side of the gear box of your motor-mower (see figure 1, item 1). Engine identification refer to the engine operation and maintenance man- ual. Ec marking the motor-mower is marked ec in compliance with the di...
Page 8
5 identification data motor-mower identification the serial number is stamped on the engine side of the gear box of your motor-mower (see figure 1, item 1). Engine identification refer to the engine operation and maintenance man- ual. Ec marking the motor-mower is marked ec in compliance with the di...
Page 9
6 technical specifications engine the motor-mower may be fitted with the following en- gines: − honda gc 160; 4 stroke benzina; 3,7 kw (5 hp); 160 cm 3 . − lombardini lga 226; 4 stroke benzina; 4 kw (5,4 hp); 220 cm 3 . Starting auto-winder device. Clutch cone type in oil bath with control lever on ...
Page 10
7 safety device the machine is fitted with an engine shut-off device to ensure maximum safety in machine operation: − engine shut-off is an electrical device which stops the engine instantly if the handlebars are released. Warning do not interfere with safety device (engine shut-off). Do not use the...
Page 11
8 motor-mower controls see fig. 3. 1. Clutch lever. 2. Engine stop lever. 3. Gear lever. 4. Pto control lever. 5. Throttle control lever. 6. Pto instant adaptor. Operating the controls clutch lever (see figure 4) − lever (1) pulled up: clutch disengaged. − lever (1) released: clutch engaged. Engine ...
Page 12
9 power take off (pto) control lever the power take off (pto) control lever engages the drive to the attachment. To engage and disengage drive, proceed as follows (see fig. 6): a. Turn throttle control lever to idle position. B. Pull up clutch lever. C. Pull pto control lever (1) and release it when...
Page 13
10 operating the motor-mower starting the engine note see the engine operating and maintenance manual for all information regarding the engine. Caution oil bath air filter (if fitted) - when delivered new, there is no oil in the air filter. Before using your mo- tor-mower, add motor oil up to the ma...
Page 14
11 mounting the 2 nd wheel (upon request) to mount the 2 nd wheel kit, follow the below steps: a. Insert there spacer (3) into the wheel hexagon (1) and fix it by the safety pin (4). B. Install the second wheel (2) and fix it by its screw (6) and washer (5). − this procedure has to be done on both w...
Page 15
12 every 300 hours change the gearbox and transmission oil following the instructions given above in the paragraph cover- ing running in. Power take off every 8 hours grease the pto (see figure 14, item 1). Also grease the pto every time you fit a new attach- ment. Checks and adjustments clutch leve...
Page 16
13 cutter bar mower warning • when you transport your machine, and when you finish work, always fit the knife guard over the cut- ter bar. • keep your hands and feet clear of the cutter bar when in motion. • do not operate the motor-mower in proximity of children and/or animals. • stop the engine be...
Page 17
14 b. Loosen lock nut (5) and turn wear plate adjuster screw (4) to obtain correct sliding movement of the knife. C. Tighten again the securing nut (5) and the screws (1) and (2). Mowing bar e.S.M. Type s note the mowing bar type e.S.M. Type s does not require any special adjustment as it is self-ad...
Page 18
15 cutter bar mowers maintenance mechanical con-rod drive lubrication after the first 5 hours of work, and subsequently af- ter every 10 hours, grease the mower mechanism at points (1) and (2) as shown in fig.5. Cam mechanism movement lubrication greasing or lubrication points are not available in t...
Page 19
Gb san martino in rio, 01.11.2001 ec certificate of conformity according to ecc 89/392 directives and successive modifications declare on their own responsibility, that the machine valpadana 42018 san martino in rio (re) italy s.P.A. S.E.P. Bc 90 (1+1) a x00000 pr en 12733 motor-mower g30 h301096 h3...
Page 20
Edizione giugno 2006 cod . 218984 m5 ® valpadana s.P.A. Società unipersonale appartenente al gruppo industriale argo s.P.A. 42018 s. Martino in rio (re) italy via don pasquino borghi, 6 tel. 0522 73.17.11 - fax 0522 73.17.31 e-mail: infosep@sep.It - http://www.Sep.It.