Summary of PediJoy
Page 1
Whirlpool pedicure spa manual pedi.
Page 2
Important requirements requires that you contact your local, licensed plumber and licensed electrician to install your new spa. Installation must be in compliance with all local and state building codes. Your pedicure spa can not operate efficiently or safely unless it is provided with adequate elec...
Page 3
53 ” 29 ” whirlpool pedicure spa salontech llc 57 seaview blvd. Port washington, ny 11050 tel: 516-484-4937 fax: 516-484-4938 www.Salontech.Com info@salontech.Com serial number: order number: installed by: installation date: chair serial number important information pedi.
Page 4
Important considerations electrical service a 110v, 60 hz, 15 amp gfci protected grounded circuit must be used to supply power to each individual pedicure spa. Water supply all plumbing connections must conform to local codes. Water supply to the spa should be provided with adequate water pressure a...
Page 5: Caution
Caution warranty will be null and void. Please do not lift or move the spa with faucet handle.
Page 6
Components due to continuous improvements on all our products, specification, characteristics, packing, color, designs re subject to change without notice identifying components 1 - auto slider remote control (automatic slider) 2 - clean pipeless jet / clean jet cover 3 - shower sprayer 4- shower st...
Page 7
Dual clean pipeless system with adjustable air control system for powerful whirlpool action dimension & weight capacity of tub switch whirlpool power source plumbing source warranty pedi-joy (base unit) pedi-joy (chair) stool clean jet air control motor discharge pump (optional) massage system hot w...
Page 8
Salontech,llc pedi-joy salontech,llc top / rear view pedi wall 2-3/4” 3” 10” 2” plumbing fitting 15” 42” 38” 29” 27” 26” plumbing connection area d ra in p ip e ex te n si o n c en te r o f d ra in t o e n d o f d ra in p ip e r eq u ir ed s p ac e fo r in st al la ti o n 54”.
Page 9
Installation specifications summary warning: failure to comply with federal, state or local codes and ordinances will result in warranty being null and void. As stated, the pedicure spa installation must comply with all plumbing and electrical codes. A licensed plumber and licensed electrician must ...
Page 10
Note: the requirement for the vacuum breaker varies from state to state and province to province, please consult with the licensed plumber. Pedi w a ll d r a in f lo o r d r a in p o w e r d r a in m a n u fa c tu r e r in st a ll a ti o n r e c o m m e n d e d note: plumber must utilize hot & cold ...
Page 11
15” back flow preventive device located in front of the hot / cold water inlet 2” above the water level of the tub. Model # v00275 class 6811 61 - plumbing fitting and accessories - fitting - certified to ansi/nsf - 61 breaded flex hose ½”brass nipples plastic faucet lock nut back flow preventive de...
Page 12
Position partial: press kneading or compression and then partial to have a partial stroke up/down 3. Massage system important safety instructions to reduce risk of burns, fire, electric shock or injury read all instructions before using ; burns will result from improper use, never remove cover other...
Page 13
R e a r r e a r chair assembly bottom view (chair) align rear of the hole onto the swivel and tighten one at a time. Swivel pre-install swivel to the base. Base (body) base with spacer for reinforcement and support swivel as well as chair. Tool required 13 mm rachet vise grip plier.
Page 14
Maintenance suction it is important to keep the suction screen from any blockage or obstructions at all times, due to they may reduce the whirlpool action and may cause damage to the pump. To clean: take off suction screen by removing two screws and clean with soft brush while immersed in disinfecta...
Page 15
Clean jet system - clean jet system users to open 1. Hold the jet cover as shown left. 2. Gently rotate to left to open. 3. Pull gently outward. 4. Clean jet component, remove all debris from jet cover and locking mechanism. 5. Clean all debris inner side of the jet as shown below left. 6. All jet c...
Page 16
Chair maintenance note: always clear passage of the up/down movement. 1- as shown, lubrication is must be applied quarterly. 2- check loose wire on limited switch. 3- do not lubricated excessively. 4- no debris on moving track or the main shaft. Outside cover open zipper to either side under the hea...
Page 17: Warning
Cautions to reduce the potential risk of fire, electrical shock or injury : 1. All electrical wiring (both installation and repair) must be done by a licensed electrician and in accordance with local and state ordinances. 2. No modifications, addition or deletions should be made to the pump without ...
Page 18
Installation instruction operation instruction please! Do not run dry 1. Turn to open drain plug. 2. Press on/off switch to activate timer. 3. At any time, water drain completely from the basin. Press on/off switch to stop or built in two minute timer. On/off switch fastner 1-3/8” hole for on/off sw...
Page 19: Warranty Form
Return address: salontech llc 57 seaview blvd. Port washington ny 11050 t: 516.484.4937 f: 516.484.4938 e-mail: info@salontech.Com web : www.Salontech.Com salon name: telephone#: alt. Tel: contact name: address : are you interest in purchasing additional equipments in near future? If so, how many? C...
Page 20: Salontech Limited Warranty
No distributor or other person has any authority to bind to change or add this warranty or its products. Is not responsible for such warranties or representations. If receives defective product notice during the applicable warranty period, shall either repair or replace the defective parts at salont...